CAMSHAFT > REMOVAL |
| 1. REMOVE TIMING BELT |
| 2. REMOVE IGNITION COIL ASSEMBLY |
Disconnect the 4 ignition coil connectors.
Remove the 4 bolts and 4 ignition coils.
| 3. REMOVE CYLINDER HEAD COVER (for RH Side) |
![]() |
Remove the 9 bolts, 9 seal washers, cylinder head cover and gasket.
| 4. REMOVE CYLINDER HEAD COVER (for LH Side) |
![]() |
Remove the 9 bolts, 9 seal washers, cylinder head cover and gasket. Remove the cylinder head cover.
| 5. REMOVE CAMSHAFT TIMING PULLEY SUB-ASSEMBLY RH |
![]() |
Hold the camshaft with a wrench, and remove the 4 bolts and timing pulley.
| 6. REMOVE CAMSHAFT TIMING PULLEY SUB-ASSEMBLY LH |
![]() |
Hold the camshaft with a wrench, and remove the 4 bolts and timing pulley.
| 7. REMOVE CAMSHAFT POSITION SENSOR |
Remove the bolt, stud bolt and camshaft position sensor.
| 8. REMOVE CAMSHAFT (for RH Side) |
![]() |
![]() |
Bring the service bolt hole of the sub-gear upward by turning the hexagonal portion of the exhaust camshaft with a wrench.
Secure the sub-gear to the main gear with a service bolt.
| Thread diameter | 6 mm |
| Thread pitch | 1.0 mm |
| Bolt length | 16 to 20 mm |
![]() |
Set the timing mark (1-dot mark) of the camshaft main gear at approx. 10° angle by turning the hexagonal portion of the exhaust camshaft with a wrench.
![]() |
Uniformly loosen and remove the 22 bearing cap bolts in several steps, in the order shown in the illustration.
Remove the oil feed pipe, 9 bearing caps, camshaft housing plug, oil control valve filter, and camshafts.
![]() |
Mount the hexagonal portion of the camshaft in a vise.
Remove the screw plug and seal washer.
![]() |
Using a 10 mm hexagon wrench, remove the bolt.
Pull out the timing tube and drive gear from the camshaft.
![]() |
Using SST and a 5 mm hexagon wrench, remove the 4 bolts, drive gear and oil seal.
| 9. REMOVE CAMSHAFT (for LH Side) |
![]() |
Bring the service bolt hole of the sub-gear upward by turning the hexagonal portion of the exhaust camshaft with a wrench.
Secure the sub-gear to the main gear with a service bolt.
| Thread diameter | 6 mm |
| Thread pitch | 1.0 mm |
| Bolt length | 16 to 20 mm |
![]() |
Align the timing marks (2-dot marks) of the camshaft drive and driven gears by turning the hexagonal portion of the exhaust camshaft with a wrench.
![]() |
Uniformly loosen and remove the 22 bearing cap bolts in several steps, in the order shown in the illustration.
Remove the oil feed pipe, 9 bearing caps, camshaft housing plug, oil control valve filter, and camshafts.
![]() |
Mount the hexagonal portion of the camshaft in a vise.
Remove the screw plug and seal washer.
![]() |
Using a 10 mm hexagon wrench, remove the bolt.
Pull out the timing tube and drive gear assembly from the camshaft.
![]() |
Using SST and a 5 mm hexagon wrench, remove the 4 bolts, drive gear and oil seal.
| 10. REMOVE SEMICIRCULAR PLUG |
| 11. REMOVE CAMSHAFT SUB GEAR |
![]() |
Mount the hexagonal portion of the camshaft in a vise.
![]() |
Using SST, turn the sub gear clockwise and remove the service bolt.
![]() |
Using snap ring pliers, remove the snap ring.
Remove the wave washer, sub gear and gear spring.
![]() |
Using a vernier caliper, measure the gap distance of the gear spring.
| 12. REMOVE CAMSHAFT HOUSING PLUG |