CAMSHAFT > INSTALLATION |
| 1. INSTALL CAMSHAFT |
![]() |
Align the mark link (yellow) with the timing mark (1-dot mark) of the camshaft timing gear as shown in the illustration.
Apply new engine oil to the thrust portions and journals of the camshafts.
![]() |
Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.
![]() |
Align the knock pin hole of the camshaft timing gear with the knock pin of the No. 1 camshaft, and insert the No. 1 camshaft into the camshaft timing gear.
Temporarily install the camshaft timing gear set bolt.
![]() |
Set the No. 1 camshaft onto the RH cylinder head with the cam lobes of the No. 1 cylinder facing downward as shown in the illustration.
![]() |
Install the 4 bearing caps in their proper locations.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Using several steps, install and tighten the 8 bearing cap bolts uniformly in the sequence as shown in the illustration.
![]() |
Rotate the No. 1 camshaft clockwise using a wrench so that the timing mark of the camshaft timing gear is aligned with the timing mark of the camshaft bearing cap.
![]() |
Align the paint mark of the No. 1 chain with the timing mark of the camshaft timing gear.
![]() |
Hold the hexagonal portion of the No. 1 camshaft with a wrench, and tighten the camshaft timing gear set bolt.
| 2. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
While pushing in the tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it.
![]() |
Temporarily install the camshaft timing gear and No. 2 chain tensioner and align the mark links (yellow) with the timing marks (1-dot mark) of the camshaft timing gears.
Tighten the No. 2 chain tensioner bolt.
| 3. INSTALL NO. 2 CAMSHAFT |
![]() |
Set the No. 2 camshaft onto the RH cylinder head with the cam lobes of the No. 1 cylinder facing upward as shown in the illustration.
![]() |
Install the 4 bearing caps in their proper locations.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Using several steps, install and tighten the 8 bearing cap bolts uniformly in the sequence as shown in the illustration.
![]() |
Rotate the No. 2 camshaft clockwise using a wrench so that the knock pin of the No. 2 camshaft is aligned with the knock pin hole of the camshaft timing gear.
![]() |
Hold the hexagonal portion of the No. 2 camshaft with a wrench, and install the camshaft timing gear set bolt.
Remove the pin from the No. 2 chain tensioner.
| 4. INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY |
![]() |
Align the mark link (yellow) with the timing mark (2-dot mark) of the camshaft timing gear as shown in the illustration.
Apply new engine oil to the thrust portions and journals of the camshafts.
![]() |
Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.
![]() |
Align the knock pin hole of the camshaft timing gear with the knock pin of the No. 3 camshaft, and insert the No. 3 camshaft into the camshaft timing gear.
Temporarily install the camshaft timing gear set bolt.
![]() |
Set the No. 3 camshaft onto the LH cylinder head with the cam lobes of the No. 2 cylinder facing downward as shown in the illustration.
![]() |
Install the 4 bearing caps in their proper locations.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Using several steps, install and tighten the 8 bearing cap bolts uniformly in the sequence as shown in the illustration.
![]() |
Set the paint mark of the No. 1 chain between the timing marks of the camshaft timing gear.
![]() |
Hold the hexagonal portion of the No. 3 camshaft with a wrench, and tighten the camshaft timing gear set bolt.
| 5. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
While pushing in the tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it.
![]() |
Temporarily install the camshaft timing gear and No. 3 chain tensioner and align the mark links (yellow) with the timing marks (1-dot mark and 2-dot mark) of the camshaft timing gears.
Tighten the chain tensioner No. 3 bolt.
| 6. INSTALL NO. 4 CAMSHAFT SUB-ASSEMBLY |
![]() |
Align the knock pin hole of the camshaft timing gear with the knock pin of the No. 4 camshaft, and insert the No. 4 camshaft into the camshaft timing gear.
Temporarily install the camshaft timing gear set bolt.
![]() |
Install the 4 bearing caps in their proper locations.
Apply a light coat of engine oil to the threads of the bearing cap bolts.
![]() |
Using several steps, install and tighten the 8 bearing cap bolts uniformly in the sequence as shown in the illustration.
![]() |
Hold the hexagonal portion of the No. 4 camshaft with a wrench, and tighten the camshaft timing gear set bolt.
Remove the pin from the No. 3. chain tensioner
![]() |
Release the chain tension between the camshaft timing gear (RH bank) and crankshaft timing gear by turning the crankshaft pulley clockwise slightly.
| 7. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.
While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate.
Install the chain tensioner with the 2 bolts.
Remove the bar from the chain tensioner.
Install a new gasket and the timing chain cover plate with the 4 bolts.
![]() |
Turn the crankshaft pulley 2 complete revolutions slowly, and align the notch with the timing mark "0" of the timing chain cover.
![]() |
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
| 8. SET NO. 1 CYLINDER TO TDC / COMPRESSION |
![]() |
Turn the crankshaft pulley, and align the notch with the timing mark "0" of the timing chain cover.
![]() |
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.
| 9. INSPECT VALVE CLEARANCE |
![]() |
Check the valves indicated in the illustration.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.
![]() |
Turn the crankshaft 2/3 of a revolution (240°), and check the valves indicated in the illustration.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.
![]() |
Turn the crankshaft 2/3 of a revolution (240°), and check the valves indicated in the illustration.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.
| 10. ADJUST VALVE CLEARANCE |
![]() |
Set the No. 1 cylinder to the TDC /compression.
Turn the crankshaft pulley, and align the notch with the timing mark "0" of the timing chain cover.
![]() |
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.
![]() |
Place paint marks on the No. 1 chain links that correspond with the timing marks of the camshaft timing gears.
Remove the No. 1 chain tensioner assembly.
![]() |
Remove the 4 bolts, timing chain cover plate and gasket.
![]() |
While rotating the stopper plate of the tensioner clockwise, push in the plunger of the chain tensioner as shown in the illustration.
While rotating the stopper plate of the tensioner counterclockwise, insert a bar of φ3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate.
Remove the 2 bolts and chain tensioner.
Remove the No. 2 camshaft.
![]() |
While raising the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it.
![]() |
Hold the hexagonal portion of the No. 2 camshaft with a wrench, and remove the camshaft timing gear set bolt.
Separate the camshaft timing gear from the No. 2 camshaft.
![]() |
Rotate the camshaft counterclockwise using a wrench so that the cam lobes of No. 1 cylinder face upward as shown in the illustration.
![]() |
Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence as shown in the illustration.
Remove the 4 bearing caps and No. 2 camshaft.
![]() |
Remove the No. 2 chain tensioner assembly.
Remove the No. 2 chain tensioner bolt, and then remove the No. 2 chain tensioner and camshaft timing gear.
Remove the camshaft.
![]() |
Hold the hexagonal portion of the No. 1 camshaft with a wrench, and loosen the camshaft timing gear set bolt.
![]() |
Slide the camshaft timing gear and separate the No. 1 chain from the camshaft timing gear.
![]() |
Rotate the No. 1 camshaft counterclockwise using a wrench so that the cam lobes of the No. 1 cylinder face upward as shown in the illustration.
![]() |
Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence as shown in the illustration.
Remove the 4 bearing caps.
![]() |
Remove the camshaft timing gear set bolt with the No. 1 camshaft lifted up, and then remove the No. 1 camshaft and camshaft timing gear with No. 2 chain.
![]() |
Tie the No. 1 chain with a string as shown in the illustration.
Remove the No. 4 camshaft sub-assembly.
![]() |
While pushing down the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it.
![]() |
Hold the hexagonal portion of the No. 4 camshaft with a wrench, and remove the camshaft timing gear set bolt.
Separate the camshaft timing gear from the No. 4 camshaft.
![]() |
Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence as shown in the illustration.
Remove the 4 bearing caps and No. 4 camshaft.
![]() |
Remove the No. 3 chain tensioner assembly.
Remove the No. 3 chain tensioner bolt, and then remove the No. 3 chain tensioner and camshaft timing gear.
Remove the No. 3 camshaft sub-assembly.
![]() |
Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence as shown in the illustration.
Remove the 4 bearing caps.
![]() |
Hold the No. 1 chain, and remove the No. 3 camshaft, camshaft timing gear and No. 2 chain.
![]() |
Tie the No. 1 chain with a string as shown in the illustration.
Remove the valve lifters.
![]() |
Determine the size of the valve lifter to be installed according to the following formulas or charts.
Using a micrometer, measure the thickness of the removed lifter.
Calculate the thickness of a new lifter so that the valve clearance comes within the specified value.
Select a new lifter with a thickness as close as possible to the calculated value.


Install the No. 3 camshaft sub-assembly.
![]() |
Align the mark link (yellow) with the timing mark (2-dot mark) of the camshaft timing gear as shown in the illustration.
Apply new engine oil to the thrust portions and journals of the camshafts.
![]() |
Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.
![]() |
Set the No. 3 camshaft onto the LH cylinder head with the cam lobes of the No. 2 cylinder facing downward as shown in the illustration.
![]() |
Install the 4 bearing caps in their proper locations.
Apply a light coat of engine oil to the threads of the bearing cap bolts.
![]() |
Install the 8 bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence as shown in the illustration.
![]() |
Set the paint mark of the No. 1 chain between the timing marks of the camshaft timing gear.
![]() |
Install the No. 3 chain tensioner assembly.
While pushing in the tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it.
![]() |
Temporarily install the camshaft timing gear and No. 3 chain tensioner and align the mark links (yellow) with the timing marks (1-dot mark and 2-dot mark) of the camshaft timing gears.
Tighten the No. 3 chain tensioner bolt.
Install the No. 4 camshaft sub-assembly.
![]() |
Align the knock pin hole on the camshaft timing gear with the knock pin of the No. 4 camshaft, and insert the No. 4 camshaft into the camshaft timing gear.
Temporarily install the camshaft timing gear set bolt.
![]() |
Install the 4 bearing caps in their proper locations.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Install the 8 bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence as shown in the illustration.
![]() |
Hold the hexagonal portion of the No. 4 camshaft with a wrench, and tighten the camshaft timing gear set bolt.
Remove the pin from the No. 3 chain tensioner.
Install the camshaft.
![]() |
Align the mark link (yellow) with the timing mark (1-dot mark) of the camshaft timing gear as shown in the illustration.
Apply new engine oil to the thrust portions and journals of the camshafts.
![]() |
Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.
![]() |
Align the knock pin hole of the camshaft timing gear with the knock pin of the No. 1 camshaft, and insert the No. 1 camshaft into the camshaft timing gear.
Temporarily install the camshaft timing gear set bolt.
![]() |
Set the No. 1 camshaft onto the RH cylinder head with the cam lobes of the No. 1 cylinder facing downward as shown in the illustration.
![]() |
Install the 4 bearing caps in their proper locations.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Install the 8 bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence as shown in the illustration.
![]() |
Rotate the No. 1 camshaft clockwise using the hexagonal portion of the No. 1 camshaft so that the timing mark of the camshaft timing gear is aligned with the timing mark of the camshaft bearing cap.
![]() |
Align the paint mark of the No. 1 chain with the timing mark of the camshaft timing gear.
![]() |
Hold the hexagonal portion of the No. 1 camshaft with a wrench, and tighten the camshaft timing gear set bolt.
![]() |
Install the No. 2 chain tensioner assembly.
While pushing in the tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it.
![]() |
Temporarily install the camshaft timing gear and No. 2 chain tensioner and align the mark links (yellow) with the timing marks (1-dot mark) of the camshaft timing gears.
Tighten the No. 2 chain tensioner bolt.
Install the No. 2 camshaft.
![]() |
Set the No. 2 camshaft onto the RH cylinder head with the cam lobes of No. 1 cylinder facing upward as shown in the illustration.
![]() |
Install the 4 bearing caps in their proper locations.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Install the 8 bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence as shown in the illustration.
![]() |
Rotate the No. 2 camshaft clockwise using a wrench so that the knock pin of the No. 2 camshaft is aligned with the knock pin hole of the camshaft timing gear.
![]() |
Hold the hexagonal portion of the No. 2 camshaft with a wrench, and install the camshaft timing gear set bolt.
Remove the pin from the No. 2 chain tensioner.
![]() |
Install the No. 1 chain tensioner assembly.
While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.
While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate.
Install the chain tensioner with the 2 bolts.
Remove the bar from the chain tensioner.
Install a new gasket and the timing chain cover plate with the 4 bolts.
![]() |
Turn the crankshaft pulley 2 complete revolutions slowly, and align the notch with the timing mark "0" of the timing chain cover.
![]() |
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
| 11. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH |
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.
![]() |
Apply a continuous bead of seal packing (diameter: 2 to 3 mm (0.08 to 0.12 in.)) to the cylinder head and timing chain cover as shown in the illustration.
Install the seal washers to the bolts.
![]() |
Install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
| 12. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.
![]() |
Apply a continuous bead of seal packing (diameter: 2 to 3 mm (0.08 to 0.12 in.)) to the cylinder head and timing chain cover as shown in the illustration.
Install the seal washers to the bolts.
![]() |
Install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
| 13. INSTALL IGNITION COIL ASSEMBLY |
| 14. INSTALL INTAKE AIR SURGE TANK |
Install a new gasket to the intake air surge tank.
Using the socket hexagon wrench 8, install the intake air surge tank with the 4 bolts.
Install the 2 intake air surge tank nuts.
Install the 2 surge tank stays with the 4 bolts.
Install the oil baffle plate with the bolt.
Install the throttle body bracket with the 2 bolts.
Install the 3 wire harness clamps and hose clamp.
Connect the throttle body with motor connector.
Connect the 2 VSV connectors.
Connect the ventilation hose.
Connect the fuel vapor feed hose.
Connect the 2 water by-pass hoses.
| 15. INSTALL AIR CLEANER ASSEMBLY |
![]() |
Install the air cleaner with the 2 bolts.
Tighten the 2 hose clamps.
![]() |
Install the 2 wire harness clamps.
Connect the mass air flow meter connector.
Connect the vacuum hose.
![]() |
Connect the ventilation hose No. 2.
| 16. CONNECT NO. 2 VENTILATION HOSE |
| 17. ADD ENGINE COOLANT |
Slowly fill the system with engine coolant.
Install the radiator cap securely.
Bleed the cooling system.
Open the heater water valve while warming up the engine.
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine.
Stop the engine and wait until the coolant cools down.
Add coolant into the reservoir until the coolant level is FULL.
| 18. CHECK FOR ENGINE COOLANT LEAKAGE |
Fill the radiator with coolant and attach a radiator cap tester.
Pump it to 118 kPa (1.2 kgf/cm2 17.1 psi), then check for leakage.
| 19. INSTALL V-BANK COVER |
Install the V-bank cover with the 2 nuts.
| 20. INSPECT IGNITION TIMING |
Warm up the engine.
![]() |
When using the intelligent tester.
Connect the intelligent tester to the DLC3.
Select the following menu items: DIAGNOSIS / ENHANCED OBD ll / DATA LIST / IGN ADVANCE.
Inspect the ignition timing during idling.
Check that the ignition timing advances immediately when the engine speed is increased.
![]() |
When not using intelligent tester.
Using SST, connect the terminals 13 (TC) and 4 (CG) of the DLC3.
Remove the air cleaner cap sub-assembly.
![]() |
Pull out the wire harness as shown in the illustration.
Connect the tester probe of a timing light to the wire of the ignition coil connector for No. 1 cylinder.
![]() |
Inspect the ignition timing during idling.
Remove the SST from the DLC3.
Inspect the ignition timing during idling.
Disconnect the timing light from the engine.
Install the air cleaner cap sub-assembly.