Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Manual Up / Down Function does not Operate on Back Door Only

for Preparation Click here


DESCRIPTION

If the back door power window does not operate, the retract switch in the rear wiper motor, the back door power window motor or the wire harness may be abnormal.

WIRING DIAGRAM


B062906E01


INSPECTION PROCEDURE

1.CHECK REAR WIPER OPERATION


    B062907E01
  1. Turn the ignition switch ON.

  1. Operate the rear wiper and turn the rear wiper switch OFF.

  1. Check that the rear wiper stops at the retract position when the rear wiper switch is turned OFF.



NG
REPAIR OR REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY
OK


2.INSPECT BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY
  1. Using the hand?held tester, read the DTC when the back power window switch is operated.

    1. When DTC B1287 is output, proceed to A.

    2. When no DTC is output, proceed to B.

    3. When DTC B1241 is output, proceed to C.



A
INSPECT MULTIPLEX COMMUNICATION SYSTEM

B
INSPECT BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY
C


3.PERFORM ACTIVE TEST BY INTELLIGENT TESTER
  1. Check the condition of the retract switch using the data list.

    Standard:
    Data list for back door ECU:

    Measurement Item
    Label
    Perameter
    Wiper retract switch
    WIPER RTRCT SW
    ON



NG
Go to step 6
OK


4.WIRE HARNESS (BACK DOOR ECU - POWER WINDOW MOTOR) (BACK DOOR ECU - GROUND)


    B062905E02
  1. Disconnect the B9 ECU connector.

  1. Disconnect the B11 motor connector.

  1. Check the continuity between the wire harness side connectors.

    Standard:
    Terminal No.
    Specified Condition
    B9-25 - B11-5
    Continuity
    B9-13 - B11-4
    Continuity

  1. Check the continuity between the B9 ECU connector and the body ground.

Standard:
Terminal No.
Specified Condition
B9-13 - Body ground
No continuity
B9-25 - Body ground
No continuity



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.INSPECT BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B062908E01
  1. Remove the motor.

  1. Apply battery voltage between the connector terminals and check that the motor gear rotates smoothly.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 4 and 5.

    Standard:
    Terminal No.
    Specified Condition
    Battery positive voltage → 5
    Battery negative voltage → 4
    Counterclockwise
    Battery positive voltage → 4
    Battery negative voltage → 5
    Clockwise



NG
REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY
OK

CHECK AND REPLACE MULTIPLEX NETWORK DOOR ECU BACK 

6.CHECK WIRE HARNESS (BACK DOOR ECU - POWER WINDOW MOTOR) (BACK DOOR ECU - GROUND)


    B062909E02
  1. Disconnect the B9 ECU connector.

  1. Disconnect the B23 motor connector.

  1. Check the continuity between the wire harness side connectors.

    Standard:
    Terminal No.
    Specified Condition
    B9-12 - R23-1
    Continuity
    B9-13 - R23-2
    Continuity

  1. Check the continuity between the B9 ECU connector and the body ground.

Standard:
Terminal No.
Specified Condition
B9-12 - Body ground
No continuity
B9-18 - Body ground
No continuity



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY