Home › TRANSMISSION · A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)

DTC    P0771    Shift Solenoid "E" Performance (Shift Solenoid Valve SR)

for Preparation Click here


SYSTEM DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).

DTC No.
DTC Detection Condition
Trouble Area
P0771
Gear required by the ECM does not match the actual gear when driving. (2-trip detection logic)
  1. Shift solenoid valve SR remains open or closed
  2. Shift solenoid valve SL1 remains open or closed
  3. Valve body is blocked
  4. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

This DTC indicates a stuck ON malfunction or stuck OFF malfunction of the shift solenoid valve SR and SL1.
The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0771:
Shift solenoid valve SR/OFF malfunction
Shift solenoid valve SR/ON malfunction
Required sensors/Components (Main)
Shift solenoid valve SR
Required sensors/Components (Related)
Speed sensor (NT), Speed sensor (NO), Crankshaft position sensor (NE)
Frequency of operation
Continuous
Duration
OFF malfunction (A): 0.4 sec.
OFF malfunction (B) and (C): Immediate
ON malfunction: 0.15 sec.
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All: 
The monitor will run whenever this DTC is not present.
P0115 - P0118 (ECT sensor)
P0125 (Insufficient ECT for Closed Loop)
P0500 (VSS)
P0748 - P0798 (Trans solenoid (range))
Turbine speed sensor circuit
Not circuit malfunction
Output speed sensor circuit
Not circuit malfunction
Shift solenoid valve S1 circuit
Not circuit malfunction
Shift solenoid valve S2 circuit
Not circuit malfunction
Shift solenoid valve SR circuit
Not circuit malfunction
Shift solenoid valve SL1 circuit
Not circuit malfunction
Shift solenoid valve SL2 circuit
Not circuit malfunction
ECT (Engine coolant temperature) sensor circuit
Not circuit malfunction
KCS sensor circuit
Not circuit malfunction
ETCS (Electric throttle control system)
Not system down
Transmission range
"D"
ECT
40°C (104°F) or more
Spark advance from Max. retard timing by KCS control
0° CA or more
Engine
Starting

OFF malfunction (A) 
ECM selected gear
5th
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
6.5% or more at 2,000 rpm (Vary with engine speed)

OFF malfunction (B) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Continuous time of ECM selecting 4th gear
2 sec. or more

OFF malfunction (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th

ON malfunction 
Current ECM selected gear
2nd
Last ECM selected gear
1st
Throttle valve opening angle
(During transition from 1st to 2nd gear)
5.5% or more at 3,000 rpm (Vary with turbine speed)

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]
  1. All of the following conditions are met: OFF malfunction (A), (B) and (C)
    2 detections are necessary per driving cycle
    1st detection; temporary flag ON
    2nd detection; pending fault code ON

    OFF malfunction (A) 
    Turbine speed/Output speed
    0.93 to 1.07

    OFF malfunction (B) 
    Turbine speed/Output speed
    Not change as follow
    0.93 to 1.07
    ↓
    0.65 to 0.79

    OFF malfunction (C) 
    Output record from ECM for 4th → 5th upshifting
    Recorded
[ON malfunction]
  1. 2 detections are necessary per driving cycle
    1st detection; temporary flag ON
    2nd detection; pending fault code ON

    Turbine speed - Output speed x 1st gear ratio (NT - NO x 1st gear ratio)
    150 rpm or more

INSPECTION PROCEDURE


ACTIVE TEST

HINT:
Performing the ACTIVE TEST using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST / SHIFT".

  7. According to the display on the tester, perform the "ACTIVE TEST".

    HINT:
    While driving, the shift position can be forcibly changed with the intelligent tester.
    Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you to confirm the problem (Click here).


    Item
    Test Details
    Diagnostic Note
    SHIFT
    [Test Details]
    Operate the shift solenoid valve and set the each shift position by yourself.
    [Vehicle Condition]
    1. IDL: ON
    2. Less than 50 km/h (31 mph)
    [Others]
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check the operation of the shift solenoid valves.

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
    2. The 4th to 5th up-shiftings must be performed with the accelerator pedal released.
    3. The 5th to 4th down-shiftings must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the ECM is shown in the DATA LIST (SHIFT) display on the intelligent tester.
    6. The shift solenoid valve SR and SL1 turns ON/OFF normally when the shift lever is in the D position:

      ECM gear shift command
      1st
      2nd
      3rd
      4th
      5th
      Shift solenoid valve SR
      OFF
      OFF
      OFF
      OFF
      ON
      Shift solenoid valve SL1
      OFF
      OFF
      OFF
      OFF
      ON

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0771)
  1. Connect the OBD II scan tool or the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the OBD II scan tool or the intelligent tester main switch ON.

  1. When you use intelligent tester:
    Select the item "DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES".

  1. Read the DTCs using the intelligent tester.

    Result:

    Display (DTC output)
    Proceed to
    Only "P0771" is output
    A
    "P0771" and other DTCs
    B

    HINT:
    If any other codes besides "P0771" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F)
  2. Be careful to prevent SST hose from interfering with the exhaust pipe.
  3. This check must be conducted after checking and adjusting engine.
  4. Perform under condition that A/C is OFF.

HINT:
Performing the ACTIVE TEST using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Turn the ignition switch off.

  1. Lift the vehicle up.



    G020657E02
  1. Remove the test plug on the transmission case center right side and connect SST.

  1. Lower the vehicle.

  1. Fully apply the parking brake and chock the 4 wheels.

  1. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  1. Start the engine.

  1. Warm up the ATF (Automatic Transmission Fluid).

  1. Measure the line pressure when the engine is idling.

  1. Turn on the tester.

  1. Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST / SOLENOID (SLT)".

  1. Follow the instructions on the tester and perform the ACTIVE TEST.

  1. Measure the line pressure with SST.

    Item
    Test Details
    LINE PRESS UP*
    [Test Details]
    Operate the shift solenoid SLT and raise the line pressure.
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. IDL: ON

    HINT:
    OFF: Line pressure up (When the active test of "SOLENOID (SLT)" is performed, the ECM commands the SLT solenoid to turn off).
    ON: No action (normal operation)

    *: "LINE PRESS UP" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.

    OK:
    The line pressure changes as specified when performing the ACTIVE TEST.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


3.INSPECT SHIFT SOLENOID VALVE SR


    A110988E05
  1. Remove the shift solenoid valve SR.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    Solenoid Connector (SR) - Solenoid Body (SR)
    11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SR
OK


4.INSPECT SHIFT SOLENOID VALVE SL1
G020767E05
  1. Remove the shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SL1
OK


5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:
There are no foreign objects on each valve.



NG
REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY