Home › BODY › ENGINE HOOD / DOOR › BACK DOOR CLOSER SYSTEM

BACK DOOR CLOSER SYSTEM > Back Door Closer does not Operate

for Preparation Click here


DESCRIPTION

The back door ECU controls the back door closer. In response to the signals output from the switches in the back door lock, the back door closer drives the closer motor.

WIRING DIAGRAM


B064457E01


INSPECTION PROCEDURE

1.INSPECT BACK DOOR LOCK
  1. Check that the back door fully closes (fully locked) when the door is closed by hand.



NG
IMPROPER FIT OF BACK DOOR, OR A FOREIGN OBJECT IS STUCK IN BACK DOOR
OK


2.POWER SOURCE RESET
  1. Disconnect the POWER DOOR 30A fuse and reconnect it. 10 seconds later, check that the back door closer is operational.



OK
NORMAL
NG


3.INSPECT WITH MOTOR BACK DOOR LOCK ASSEMBLY


    B065423E01
  1. Check operation of the door lock.

    1. Using a screwdriver, push the latch in order to put the back door lock in the locked condition (full-latch position).

    2. Connect the positive (+) lead to terminal 1 and the negative (-) lead to terminal 2. Then, check operation of the latch.

      Standard:
      The latch turns to the open-latch position

    3. Inspect motor operation when battery voltage is applied to the terminals.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) - Terminal 2
      Battery negative (-) - Terminal 1
      Clockwise (Motor in normal rotation)
      Battery positive (+) - Terminal 1
      Battery negative (-) - Terminal 2
      Counterclockwise (Motor in reverse rotation)



    B062719E05
  1. Check the back door courtesy switch continuity.

    1. Check the continuity between the terminals of the courtesy switch.

      Standard:
      Door Lock Latch Position
      Terminal No.
      Specified Condition
      Open-latch position, Half-latch position
      4 - 5
      Continuity
      Full-latch position, Over-latch position
      4 - 5
      No continuity

  1. Check the back door latch switch continuity.

    1. Check the continuity between the terminals of the latch switch.

      Standard:
      Door Lock Latch Position
      Terminal No.
      Specified Condition
      Open-latch position, Over-latch position
      4 - 6
      Continuity
      Half-latch position, Full-latch position
      4 - 6
      No continuity

  1. Check the position switch continuity.

    1. Connect the battery positive (+) lead to connector terminal 1 and the negative (-) lead to connector terminal 2.

      Standard:
      Door Lock Latch Position
      Terminal No.
      Specified Condition
      Any position other than motor stop position
      (Motor in operation)
      3 - 4
      Continuity
      Motor stop position
      (Gear in original position
      3 - 4
      No continuity



OK
REPLACE WITH MOTOR BACK DOOR LOCK ASSEMBLY
NG


4.CHECK WIRE HARNESS (BACK DOOR LOCK - BACK BODY ECU)


    B066168E01
  1. Disconnect the B7 back door lock and B9 back door ECU connectors.

  1. Check the continuity between the terminals of the back door lock (B7) and back door ECU (B9) connectors.

    Standard (Check for open) :
    Symbols (Terminal No.)
    Specified Condition
    - (B7-5) - HALF (B9-6)
    Continuity
    - (B7-6) - FULL (B9-7)
    - (B7-4) - POS (B9-8)
    - (B7-1) - ACT+ (B9-15)
    - (B7-2) - ACT- (B9-14)
    - (B7-3) - LSE (B9-21)



OK
REPLACE MULTIPLEX NETWORK DOOR ECU
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR