Differential carrier assembly front (1GR-FE (4WD))
Differential drive pinion preload (at starting)
|
New bearing
| 0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf)
|
Reused bearing
| 0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)
|
Total preload (at starting)
| Drive pinion preload plus 0.20 to 0.63 N*m (2.0 to 6.4 kgf*cm, 1.8 to 5.6 in.*lbf)
|
Differential ring gear backlash
| 0.11 to 0.18 mm (0.0043 to 0.0071 in.)
|
Differential side gear backlash
| 0 to 0.15 mm (0 to 0.00591 in.)
|
Front differential carrier oil seal
|
Oil seal drive in depth
| 4.35 +- 0.45 mm (0.171 +- 0.018 in.)
|
Front differential side oil seal
|
Oil seal drive in depth
| 0 +- 0.45 mm (0 +- 0.0177 in.)
|
Front differential side tube oil seal
|
Oil seal drive in depth
| 5.3 +- 0.5 mm (0.2087 +- 0.0197 in.)
|
Front differential side gear needle roller bearing
|
Bearing press in depth
| 1.7 +- 0.3 mm (0.067 +- 0.012 in.)
|
Differential clutch sleeve and clutch sleeve fork clearance
|
Max.
| 0.35 mm (0.0138 in.)
|
Differential carrier assembly front (2UZ-FE (4WD))
Companion flange vertical runout
|
Max.
| 0.10 mm (0.0039 in.)
|
Differential drive pinion preload (at starting)
|
New bearing
| 0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 14 in.*lbf)
|
Reused bearing
| 0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)
|
Total preload (at starting)
| Drive pinion preload plus 0.25 to 0.45 N*m (2.5 to 4.6 kgf*cm, 2.2 to 4.0 in.*lbf)
|
Differential ring gear backlash
| 0.13 to 0.18 mm (0.0051 to 0.0071 in.)
|
Differential case runout
|
Max
| 0.04 mm (0.0018 in.)
|
Side gear backlash
| 0 to 0.15 mm (0 to 0.00591 in.)
|
Front differential carrier oil seal
|
Oil seal drive in depth
| 4.35 +- 0.45 mm (0.171 +- 0.018 in.)
|
Front differential side oil seal
|
Oil seal drive in depth
| 0 +- 0.3 mm (0 +- 0.012 in.)
|
Front differential side tube oil seal
|
Oil seal drive in depth
| 5.3 +- 0.5 mm (0.209 +- 0.020 in.)
|
Differential side gear backlash
| 0.05 to 0.20 mm (0.002 to 0.008 in.)
|
Differential ring gear backlash
| 0.13 to 0.18 mm (0.0051 to 0.0071 in.)
|
Differential carrier assembly front (4WD)
Companion flange lateral runout
|
Max.
| 0.10 mm (0.0039 in.)
|
Front differential side gear thrust washer thickness
| 1.48 to 1.52 mm (0.0583 to 0.0598 in.)
|
1.53 to 1.57 mm (0.0602 to 0.0618 in.)
|
1.58 to 1.62 mm (0.0622 to 0.0638 in.)
|
1.63 to 1.67 mm (0.0642 to 0.0657 in.)
|
1.68 to 1.72 mm (0.0661 to 0.0677 in.)
|
1.73 to 1.77 mm (0.0681 to 0.0697 in.)
|
1.78 to1.82 mm (0.0701 to 0.0717 in.)
|
1.83 to 1.87 mm (0.0720 to 0.0736 in.)
|
1.88 to1.92 mm (0.0740 to 0.0756 in.)
|
Front differential ring gear thrust washer thickness
| 1.59 to 1.61 mm (0.0626 to 0.0634 in.)
|
1.62 to 1.64 mm (0.0638 to 0.0646 in.)
|
1.65 to 1.67 mm (0.0650 to 0.0657 in.)
|
1.68 to 1.70 mm (0.0661 to 0.0669 in.)
|
1.71 to 1.73 mm (0.0673 to 0.0681 in.)
|
1.74 to 1.76 mm (0.0685 to 0.0693 in.)
|
1.77 to 1.79 mm (0.0697 to 0.0705 in.)
|
1.80 to 1.82 mm (0.0709 to 0.0717 in.)
|
1.83 to 1.85 mm (0.0720 to 0.0728 in.)
|
1.86 to 1.88 mm (0.0732 to 0.0740 in.)
|
1.89 to 1.91 mm (0.0744 to 0.0752 in.)
|
1.92 to 1.94 mm (0.0756 to 0.0764 in.)
|
1.95 to 1.97 mm (0.0768 to 0.0776 in.)
|
1.98 to 2.00 mm (0.0780 to 0.0787 in.)
|
2.01 to 2.03 mm (0.0791 to 0.0800 in.)
|
2.04 to 2.06 mm (0.0803 to 0.0811 in.)
|
2.07 to 2.09 mm (0.0815 to 0.0823 in.)
|
2.10 to 2.12 mm (0.0827 to 0.0835 in.)
|
2.13 to 2.15 mm (0.0839 to 0.0846 in.)
|
2.16 to 2.18 mm (0.0850 to 0.0858 in.)
|
2.19 to 2.21 mm (0.0862 to 0.0870 in.)
|
2.22 to 2.24 mm (0.0874 to 0.0882 in.)
|
2.25 to 2.27 mm (0.0886 to 0.0894 in.)
|
2.28 to 2.30 mm (0.0898 to 0.0906 in.)
|
2.31 to 2.33 mm (0.0909 to 0.0917 in.)
|
2.34 to 2.36 mm (0.0921 to 0.0929 in.)
|
2.37 to 2.39 mm (0.0933 to 0.0941 in.)
|
2.40 to 2.42 mm (0.0945 to 0.0953 in.)
|
2.43 to 2.45 mm (0.0957 to 0.0965 in.)
|
2.46 to 2.48 mm (0.0969 to 0.0976 in.)
|
Rear differential drive pinion plate washer thickness
| 1.69 to 1.71 mm (0.0665 to 0.0673 in.)
|
1.72 to 1.74 mm (0.0677 to 0.0685 in.)
|
1.75 to 1.77 mm (0.0689 to 0.0697 in.)
|
1.78 to 1.80 mm (0.0701 to 0.0709 in.)
|
1.81 to 1.83 mm (0.0713 to 0.0720 in.)
|
1.84 to 1.86 mm (0.0724 to 0.0732 in.)
|
1.87 to 1.89 mm (0.0736 to 0.0744 in.)
|
1.90 to 1.92 mm (0.0748 to 0.0756 in.)
|
1.93 to 1.95 mm (0.0760 to 0.0768 in.)
|
1.96 to 1.98 mm (0.0772 to 0.0780 in.)
|
1.99 to 2.01 mm (0.0783 to 0.0791 in.)
|
2.02 to 2.04 mm (0.0795 to 0.0803 in.)
|
2.05 to 2.07 mm (0.0807 to 0.0815 in.)
|
2.08 to 2.10 mm (0.0819 to 0.0827 in.)
|
2.11 to 2.13 mm (0.0831 to 0.0839 in.)
|
2.14 to 2.16 mm (0.0843 to 0.0850 in.)
|
2.17 to 2.19 mm (0.0854 to 0.0862 in.)
|
2.20 to 2.22 mm (0.0866 to 0.0874 in.)
|
2.23 to 2.25 mm (0.0878 to 0.0886 in.)
|
2.26 to 2.28 mm (0.0890 to 0.0898 in.)
|
2.29 to 2.31 mm (0.0902 to 0.0909 in.)
|
2.32 to 2.34 mm (0.0913 to 0.0921 in.)
|
Differential carrier assembly rear
Companion flange vertical runout
|
Max
| 0.10 mm (0.0039 in.)
|
Companion flange lateral runout
|
Max
| 0.10 mm (0.0039 in.)
|
Differential ring gear runout
|
Max
| 0.07 mm (0.0028 in.)
|
Rear differential case runout
|
Max
| 0.07 mm (0.0028 in.)
|
Differential drive pinion preload (at starting)
|
New bearing
| 1.05 to 1.64 N*m (10.7 to 16.7 kgf*cm, 9.3 to 14.5 in.*lbf)
|
Reused bearing
| 0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 5.0 to 7.5 in.*lbf)
|
Total preload (at starting)
| Drive pinion preload plus 0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)
|
Differential ring gear backlash
| 0.13 to 0.18 mm (0.0051 to 0.0071 in.)
|
Rear differential case side gear backlash LH
| 0.05 to 0.20 mm (0.0002 to 0.008 in.)
|
Rear differential case side gear backlash RH
| 0.05 to 0.20 mm (0.0002 to 0.008 in.)
|
Rear differential carrier oil seal
|
Oil seal drive in depth
| 0.7 +- 1.3 mm (0.0276 +- 0.0512 in.)
|
Rear differential side gear thrust washer thickness
| 0.9 mm (0.0354 in.)
|
1.0 mm (0.0394 in.)
|
1.1 mm (0.0433 in.)
|
1.2 mm (0.0472 in.)
|
1.3 mm (0.0512 in.)
|