MULTIPLEX COMMUNICATION SYSTEM > GENERAL



OUTLINE
  1. The multiplex communication system uses the 3 communication protocols (CAN, LIN, and AVC-LAN) to achieve a streamlined wiring harness configuration.

    Protocol
    Outline
    Controller Area Network (CAN)
    CAN is classified into 2 types according to communication speed, the High Speed CAN (HS-CAN) is used for the power train, chassis and body electrical systems, and the Middle Speed CAN (MS-CAN) is used for the body electrical system.
    1. The HS-CAN portions are the CAN V bus and power management bus. The MS-CAN portion is referred to as the CAN MS bus.
    2. The power management control ECU and the main body ECU (multiplex network body ECU) with gateway function are used to transmit data between the buses.
    Local Interconnect Network (LIN)
    LIN is used for local area networking, in which the system has a respective bus for each body electrical system.
    Audio Visual Communication-Local Area Network (AVC-LAN)
    AVC-LAN is used for communication only between the Audio Visual (AV) system components.

  2. There is no direct communication between CAN, LIN, and AVC-LAN networks because these multiplex communication systems are incompatible. CAN, LIN and AVC-LAN are separate networks. Because these are separate networks, some ECUs serve as gateways for the transfer of data, allowing communication between CAN and LIN networks.

  3. For the LIN network communication needs of the following systems, the following LIN buses are used:

    1. Certification Bus
    2. Air Conditioning Bus
    3. Door Bus
    4. Off-load Bus



  4. A customizable body electrical system is used, enabling some of the control functions of the ECUs to be set using the Techstream. For details, refer to the Repair Manual.

    HINT:
    Generally speaking, multiplex communication refers to the use of serial communication data that consists of bits and frames in order to exchange information among various ECUs. This allows for a reduction of the amount of wiring on the vehicle. A bit is the basic unit of communication that is used to represent the information. A bit is represented by binary values of "0" or "1". For CAN communication, a differential voltage drive is used to represent the binary values of "0" or "1". This "differential voltage drive" reduces the effects of electrical interference.


    Y100125E12

  5. Differences between CAN, LIN, and AVC-LAN

    1. The protocols, which are the rules for establishing data communication, differ between CAN, LIN, and AVC-LAN. If the ECUs in the networks use different data frameworks such as communication speed, communication wire, or signals, they will be unable to understand each other. Therefore, protocols (rules) must be established among them.

    2. Compared to LIN and AVC-LAN, CAN features high-speed data transmission. Therefore, CAN is able to transmit larger amounts of data faster than other protocols. This feature makes it possible to transmit data accurately for the power train and chassis control systems. These systems require large amounts of data to be transmitted in short periods of time.

      Protocol
      CAN
      LIN
      AVC-LAN
      HS-CAN
      MS-CAN
      Communication Speed
      500 kbps*
      250 kbps*
      9.6 to 20 kbps*
      Max. 17.8 kbps*
      Communication Wire
      Twisted-pair Wire
      AV Single Wire
      Twisted-pair Wire
      Drive Type
      Differential Voltage Drive
      Single Wire Voltage Drive
      Differential Voltage Drive
      Data Length
      1-8 Byte (Variable)
      2, 4, 8 Byte (Variable)
      0-32 Byte (Variable)
      bps*: abbreviation for "Bits Per Second", indicating the number of bits that can be transmitted per second.

    3. A twisted-pair of wires is used for CAN and AVC-LAN communication. A single Automobile Vinyl (AV) wire is used for LIN communication.

      Communication Wire
      Outline
      Twisted-pair Wire
      Y100126
      This communication wire is a pair of twisted lines. Communication is driven by applying different voltages to the 2 lines in order to send a single signal. This system, which is called a "Differential Voltage Drive", reduces noise.
      AV Single Wire
      Y100127
      This is a lightweight single communication wire that consists of a single core line surrounded by insulation. Voltage is applied to this line in order to drive communication, and this system is called a "Single Wire Voltage Drive".