FOUR WHEEL DRIVE CONTROL SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
*: Models with Multi-terrain select system

Component
Function
Combination Meter
4WD Indicator Light
Illuminates to inform the driver that the drive type is 4WD.
4LO Indicator Light
Illuminates to inform the driver that the transfer position is low range.
Multi-information Display*
Displays a message to guide the driver to switch transfer mode.
Transfer
Transfer Shift Actuator Assembly
Shifts the transfer mode (H2, H4, or L4).
Transfer Indicator Switch (4WD Position)
Detects that the drive type is 4WD.
Transfer Indicator Switch (L4 Position)
Detects that the transfer position is Low.
Front Differential
  1. A.D.D. Actuator
    1. A.D.D. Shift Motor
    2. A.D.D. Motor Limit Switch
    3. A.D.D. Detection Switch
  1. Switches the drive type (2WD or 4WD).
  2. Detects the A.D.D. state (ON or OFF).
Four Wheel Drive Control ECU
Receives the switch signals and controls the transfer actuator and A.D.D. actuator.
Transfer Position Switch
Detects the transfer mode.
ECM
Outputs signals such as the shift position signal, throttle position signal, and crankshaft position signal to the four wheel drive control ECU.

CONSTRUCTION


  1. Transfer

    1. On VF2BM transfer, the transfer shift actuator contains engagement shifting transfer shift motor, transfer shift motor limit switch, wait mechanism (spiral spring) and front drive shift fork shaft. In addition, a Transfer Indicator Switch (4WD Position) and a Transfer Indicator Switch (L4 Position) are installed in the transfer shift actuator.

    2. A planetary gear unit is used in the reduction mechanism and a silent chain is used to reduce front drive noise.



    3. A triple-cone type synchromesh mechanism is used for smooth engagement from 2WD to 4WD.


      V103901E02


      Text in Illustration 
      *1
      Transfer Input Shaft
      *2
      Planetary Gear Unit
      *3
      Transfer Shift Actuator
      *4
      High and Low Shift Fork
      *5
      Rear Output Shaft
      *6
      Silent Chain
      *7
      Front Output Shaft
      *8
      Transfer Indicator Switch (4WD)
      *9
      Transfer Indicator Switch (L4)
      *a
      Transfer Position Switch



  2. Planetary Gear Unit

    1. The planetary gear unit consists of the planetary sun gear, 4 planetary pinion gears, and planetary carrier.

    2. The planetary sun gear is integrated with the transfer input shaft.

    3. 4 planetary pinion gears are fitted to the planetary carrier. Each pinion gear shaft is fixed to the planetary carrier. A planetary spline piece is fitted to the rear of the planetary carrier. When the planetary carrier is to be connected to the output shaft, the power is transferred after engaging the splines on the spline piece with the splines on the high and low clutch sleeve. The high and low clutch sleeve is installed rearward of the transfer input shaft on the high and low clutch hub that is splined to the output shaft.



    4. The planetary ring gear is fixed to the transfer case and its internal teeth mesh with the planetary pinion gears.


      V100369E02


      Text in Illustration 
      *1
      Transfer Input Shaft
      *2
      Planetary Sun Gear
      *3
      Planetary Carrier
      *4
      Pinion Shaft
      *5
      Planetary Pinion Gear
      *6
      Planetary Ring Gear
      *7
      Planetary Spline Piece
      *8
      High and Low Clutch Sleeve
      *9
      High And Low Clutch Hub
      -
      -



  3. Transfer Shift Actuator Assembly

    1. Transfer shift actuator Assembly, which contains transfer shift motor, transfer shift motor limit switch, wait mechanism (spiral spring), and front drive shift fork shaft No.1, cannot be dissembled

    2. Transfer shift motor limit switch has a 3-contact point switch (TL1, TL2, and TL3). The combinations of 3 contact points are detected based on the shift motor position (H2, H4, or L4 mode).

    3. A wait mechanism (spiral spring) is used in shifting between H2, H4 and L4. If the operating resistance of the front drive shift fork shaft is large, the shift rotation is partially stored in spiral spring. Afterward, when the operating resistance is reduced, the spring force causes the front drive shift fork to slide.



    4. In addition, a Transfer Indicator Switch (4WD) and a Transfer Indicator Switch (L4) are installed in the transfer shift actuator.


      V103903E01


      Text in Illustration 
      *1
      Transfer Shift Actuator
      *2
      Wait Mechanism (Spiral Spring)
      *3
      Transfer Indicator Switch (4WD Position)
      *4
      Transfer Indicator Switch (L4 Position)
      *5
      Transfer Shift Motor Limit Switch (TL1, TL2, and TL3)
      -
      -

      V103904E01



  4. Automatic Disconnection Differential (A.D.D.) Shift Actuator



    1. The A.D.D. shift actuator contains the A.D.D. shift motor, A.D.D. motor limit switch and A.D.D. position switch. It should not be disassembled.


      V100370E01


      Text in Illustration 
      *1
      A.D.D. Motor Limit Switch (DL1, DL2)
      *2
      A.D.D. Position Switch
      *3
      A.D.D. Shift Motor
      -
      -
      The A.D.D. motor limit switch has two contact point switches (DL1, DL2). Different combinations of the two contact point switches and A.D.D. position switch (ADD) allow detection of the A.D.D. state (ON or OFF).

      V100371E01


OPERATION


  1. Planetary Gear Unit Operation



    1. In the H2/H4 position, the input shaft is directly connected to the output shaft via the splines at the rear of the transfer input shaft which make this connection via the movable high and low clutch sleeve.
      The high and low clutch sleeve is constantly meshed with the rear output shaft via the high and low clutch hub. Thus, the rotation of the input shaft is transmitted to the high and low clutch sleeve, to the high and low clutch hub, then to the rear output shaft.


      V103905E01


      Text in Illustration 
      *1
      Transfer Input Shaft
      *2
      Planetary Sun Gear
      *3
      Planetary Carrier (Pinion Shaft)
      *4
      Planetary Pinion Gear
      *5
      Planetary Ring Gear
      *6
      Planetary Spline Piece
      *7
      High and Low Clutch Sleeve
      *8
      Rear Output Shaft



    2. In the L4 position, the external teeth of the high and low clutch sleeve are meshed with the planetary carrier via the spline piece. Thus, the rotation of the input shaft is transmitted from the planetary sun gear, to the planetary pinion gears, to the planetary pinion gear shafts, to the planetary carrier, to the planetary spline piece, to the high and low clutch sleeve, through the high and low clutch hub, to the rear output shaft.


      V103906E01


      Text in Illustration 
      *1
      Transfer Input Shaft
      *2
      Planetary Sun Gear
      *3
      Planetary Carrier (Pinion Shaft)
      *4
      Planetary Pinion Gear
      *5
      Planetary Ring Gear
      *6
      Planetary Spline Piece
      *7
      High and Low Clutch Sleeve
      *8
      Rear Output Shaft



  2. Automatic Disconnection Differential (A.D.D.) Shift Actuator Operation



    1. From 2WD (H2) to 4WD (H4)


      V104094E01


      Step
      System Operation
      (1)
      When the transfer position switch turns to H4 position, this signal is input into the four wheel drive control ECU.
      (2)
      The four wheel drive control ECU actuates the A.D.D. shift motor.
      (3)
      The operation of the A.D.D. shift motor causes the A.D.D. shift fork and sleeve to move toward the left side, thus connecting the front differential and front drive shafts. As result, the torque from the transfer is transmitted to the front wheels.
      (4)
      The four wheel drive control ECU turns on the 4WD indicator light.



    2. From 4WD (H4) to 2WD (H2)


      V104095E01


      Step
      System Operation
      (1)
      When the transfer position switch turns to H2 position, this signal is input into the four wheel drive control ECU
      (2)
      The four wheel drive control ECU actuates the A.D.D. shift motor.
      (3)
      The operation of the A.D.D. shift motor causes the A.D.D. shift fork and sleeve to move toward the right side, thus disconnecting the front differential and front drive shafts. As result, the torque from the transfer is not transmitted to the front wheels.
      (4)
      The four wheel drive control ECU turns off the 4WD indicator light.