METER / GAUGE SYSTEM > DETAILS



FUNCTION
  1. Buzzer Function

    1. The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.

      1
      Sliding Roof Open Warning*1
      2
      Downshift Reject Warning
      3
      4WD Warning*2
      4
      Parking Brake Engaged Warning
      5
      Key Reminder*3
      6
      Immobiliser Certification Reminder*4
      7
      Smart Key Warning*4
      8
      Door Open Driving Warning
      9
      Seat Belt Warning
      10
      Brake System Warning
      11
      Multi-information Display Warning
      -
      -

      1. *1: Models with sliding roof system
      2. *2: Models with full-time 4WD system
      3. *3: Models without smart key system
      4. *4: Models with smart key system

  2. Front Seat Belt Warning Function

    1. When the ignition switch is ON, this system detects the condition of the seat belts based on the signals from the driver and front passenger seat belt buckle switches and the occupant classification sensor.

    2. When the seat belt is unbuckled, the multi buzzer sounds 5 times 1.8 seconds after the ignition switch is turned to ON.

    3. The multi buzzer sounds once when the vehicle speed exceeds 20 km/h (12.4 mph) to emphasize the fact that the seat belt is unbuckled.

    4. After 30 seconds, the buzzer starts to sound again.

    5. After 9.6 seconds, the sound changes for emphasis.

    6. The sound continues for 20 seconds.

    7. Once a multi buzzer begins to sound, it will continue until the seat belt is buckled or the ignition switch is turned to off.

      HINT:
      1. The buzzer will stop sounding if the meter ECU detects a signal from the parking brake switch or a vehicle speed signal indicating that the vehicle is parked.
      1. Upon receiving a request from a user who cannot wear a seat belt for a special reason, the multi buzzer warning can be canceled using Techstream. For details, refer to the corresponding Repair Manual for this model.

  3. Maintenance Required Reminder

    1. A maintenance required reminder display will appear to remind the driver to have maintenance performed based on the vehicle driving distance.

    2. The Combination meter assembly calculates the vehicle driving distance based on the signals from the skid control ECU.

    3. When the accumulated vehicle driving distance memorized in the meter ECU exceeds 4500 miles after being reset, the meter ECU will flash the maintenance required reminder light for approximately 16 seconds after the bulb check and remind the driver that the vehicle maintenance needs to be conducted shortly.

    4. When the accumulated vehicle driving distance memorized in the meter ECU exceeds 5000 miles after being reset, the meter ECU will illuminate the maintenance required reminder light immediately and keep it on to remind the driver to have the vehicle serviced.

    5. After maintenance has been performed, the accumulated vehicle driving distance memorized in the combination meter assembly should be reset to zero using the ODO/TRIP switch.

      HINT:
      The accumulated vehicle driving distance memorized in the combination meter assembly can be reset using the following procedure.
      1. Turn the ignition switch to ON, and make sure that the TRIP A is displayed on its Liquid Crystal Display (LCD).
      2. Turn the ignition to off. While pushing the ODO/TRIP switch, turn the ignition switch to on.
      3. With the ignition switch ON, keep holding the ODO/TRIP switch (for at least 5 seconds) with the LCD counting down. Release the ODO/TRIP switch when the resetting procedure has completed.
      4. As the resetting completes, the odometer will display "000000" for 1 second.



  4. Multi-information Display



    1. The display switches in the following order each time the ODO/TRIP switch is pressed:


      Y138632E01

      HINT:
      The illustration is a representative example.


      *a
      ODO
      *b
      TRIP A
      (If the ODO/TRIP switch is pressed for 0.8 seconds or more, the TRIP A display is reset.)
      *c
      TRIP B
      (If the ODO/TRIP switch is pressed for 0.8 seconds or more, the TRIP B display is reset.)
      -
      -



    2. The display switches in the following order each time the DISP switch is pressed:


      Y138634E01

      HINT:
      The illustration is a representative example.


      *a
      Average Fuel Consumption
      Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from ECM via CAN).
      *b
      Eco Driving Indicator Zone Display
      Eco driving ratio based on acceleration is shown with a bar graph.
      *c
      Current Fuel Consumption
      Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from ECM via CAN), provided that the ignition switch is turned to ON.
      *d
      Cruising Range
      Displays the value that has been calculated by the meter ECU, which is based on the fuel consumption data that the meter ECU continuously monitors and stores in its memory, and the residual fuel volume data, provided that the ignition switch is turned to ON.
      *e
      Elapsed Time
      Calculates and displays the elapsed time since the engine start signal was input into the combination meter assembly.
      *f
      Vehicle Speed
      Displays the value that has been calculated by the combination meter assembly based on the vehicle speed signal.
      *g
      Steering Angle
      Calculates and displays the steering angle, which is based on signals from the steering angle sensor. The steering angle is displayed in 7 stages (1 for neutral and 3 each for left and right) in accordance with the operation of the steering wheel.
      *h
      Setting
      In the custom setting display, 3 items (Language, Units, Eco Driving Indicator Light ) can be set.
      *i
      Setting is disabled
      Appears in the setting display when the vehicle speed exceeds 8 km/h.
      *j
      Blank
      -

  5. Eco Driving Indicator Light and Eco Driving Indicator Zone Display

    1. The Eco Driving Indicator starts to operate when the following conditions are met:

      1. Ignition switch is ON.
      2. Engine is running.
      3. Shift lever is in D.
      4. Vehicle is running.

    2. The Eco Driving Indicator stops operation when the following conditions are met:

      1. Ignition switch is off.
      2. Shift lever is in any position other than D.
      3. Engine is not running.

      Vehicle Condition
      Eco Driving Indicator Zone Display
      Eco Driving Indicator Light
      Stopped
      Y102135
      Turns off
      Eco Driving
      Y104369
      Turns on
      Non-eco Driving
      Y104371
      Turns off

  6. Warning Display

    1. The warning and the advisory displays interrupt the image shown in the multi-information display if the display conditions are met.

      Priority
      Display
      Master Warning Light
      Multi Buzzer
      1
      Door Open (While Driving)
      Blinks
      Sounds
      Door Open
      -
      -
      Intuitive Parking Assist System
      -
      -
      2
      AUTO POWER OFF TO CONSERVE BATTERY
      -
      -
      3
      SHIFT TO P POSITION
      Blinks
      Sounds
      4
      RELEASE PARKING BRAKE
      Blinks
      Sounds
      KEY NOT DETECTED
      Blinks
      Sounds
      5
      CHECK STEERING LOCK SYSTEM
      Illuminates
      Sounds
      HIGH AUTOMATIC TRANSMISSION FLUID TEMP. STOP VEHICLE IN A SAFE PLACE
      Illuminates
      Sounds
      CHECK TRANSMISSION SYSTEM
      Illuminates
      Sounds
      6
      TURN POWER OFF
      Blinks
      Sounds
      SHIFT TO P POSITION AND PUSH ENGINE SWITCH TO TURN POWER OFF
      Blinks
      Sounds
      KEY DETECTED IN VEHICLE
      Blinks
      Sounds
      MOONROOF OPEN
      Blinks
      Sounds
      DEPRESS BRAKE PEDAL, TOUCH ENGINE SWITCH WITH KEY
      Blinks
      Sounds
      DEPRESS BRAKE PEDAL AND PUSH ENGINE SWITCH TO START
      Blinks
      Sounds
      SHIFT TO P POSITION TO START
      Blinks
      Sounds
      7
      STEERING LOCK ACTIVE
      Blinks
      Sounds
      8
      KEY BATTERY LOW
      Illuminates
      Sounds
      CHECK SONAR SYSTEM
      Illuminates
      Sounds
      CLEAN SONAR
      Illuminates
      Sounds
      9
      LOW WASHER FLUID
      -
      -
      MAINTENANCE REQUIRED SOON
      -
      -
      MAINTENANCE REQUIRED
      -
      -
      RESETING MAINTENANCE DATA COMPLETE
      -
      -
      RESETING MAINTENANCE DATA INCOMPLETE
      -
      -

      HINT:
      The items displayed differ by vehicle specification.



  7. Custom Setting Function for Multi-information Display



    1. Setting that can be customized are displayed in the following order each time the DISP switch is pressed. 3 items can be customized.


      Y105412E01


      Item
      Customized Setting
      Default Setting
      LANGUAGE
      1. ENGLISH
      2. FRENCH
      3. SPANISH
      ENGLISH
      UNITS
      1. miles
      2. km (L/100km)
      1. miles: Models for U.S.A.
      2. km (L/100km): Models for Canada
      ECO LAMP
      1. ON
      2. OFF
      ON

      HINT:
      When multiple warning conditions occur at the same time, the highest priority warning message is displayed first.