BRAKE CONTROL SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS

Component
Function
Combination Meter Assembly
Brake System Warning Light
  1. Lights up to alert the driver when the skid control ECU detects a malfunction in the EBD.
  2. Lights up to alert the driver when the brake fluid level is low.
  3. Lights up to alert the driver that the hydraulic pressure of the brake booster accumulator assembly in the hydraulic brake booster assembly has decreased.
  4. Lights up to inform the driver of the parking brake condition.
ABS Warning Light
Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS.
Slip Indicator Light
Blinks to inform the driver when the TRAC, A-TRAC, VSC, hill-start assist control, downhill assist control, CRAWL and trailer sway control is operational.
TRAC OFF Indicator Light
Lights up to inform the driver that the TRAC OFF mode is entered using the VSC OFF switch.
VSC OFF Indicator Light
Lights up to inform the driver that the VSC OFF mode is entered using the VSC OFF switch.
Downhill Assist Control Indicator Light*1
Lights up to inform the driver when the downhill assist control switch turned on.
CRAWL Indicator Light*2
Lights up to inform the driver when the CRAWL ON/OFF switch turned on.
Multi-terrain Indicator Light*2
Lights up to inform the driver when multi-terrain select control is available.
Multi-terrain Select Indicator*2
Displays the selected road mode.
Buzzer
Sounds intermittently to inform the driver that the hill-start assist control is active.
Front and Rear Speed Sensors
Detects the wheel speed of each of the 4 wheels.
Yaw Rate and Acceleration Sensor
(Built-in Deceleration Sensor)
  1. Detects the vehicle's longitudinal and lateral acceleration.
  2. Detects the vehicle's yaw rate.
Steering Angle Sensor (Spiral Cable Sub-assembly)
Detects the direction and angle of the steering wheel.
Stop Light Switch Assembly
Detects the brake pedal depressing signal.
Parking Brake Switch Assembly
Detects that the parking brake lever is pulled up.
Center Differential Lock Detection Switch
(Built-into Transfer Shift Actuator Assembly)
Detects the center differential lock condition.
Rear Differential Lock Detection Switch*3
Detects the rear differential lock condition.
VSC OFF Switch
Enables the driver to select the "Normal Mode", "TRAC OFF Mode", or "VSC OFF Mode".
CRAWL Control Switch Assembly*2
  1. Turns the CRAWL on and off.
  2. Used to select the target vehicle speed when the CRAWL is active.
Downhill Assist Control Switch*1
Turns the downhill assist control on and off.
Hydraulic Brake Booster Assembly
Changes the brake fluid path based on the signals from the skid control ECU during the operations of the brake control functions in order to control the fluid pressure that is applied to the wheel cylinders.
Brake Fluid Level Warning Switch
(Built-into Hydraulic Brake Booster Assembly)
Detects the low brake fluid level.
Master Cylinder Pressure Sensor
(Built-into Hydraulic Brake Booster Assembly)
Detects the master cylinder pressure and outputs this signal to the skid control ECU.
Accumulator Pressure Sensor
(Built-into Hydraulic Brake Booster Assembly)
Monitors the hydraulic pressure of the brake booster accumulator assembly and outputs this signals for the brake booster pump assembly control.
Switching Solenoid Valve
(Built-into Hydraulic Brake Booster Assembly)
Switches the brake hydraulic path when the brake control system is activated.
Control Solenoid Valve
(Built-into Hydraulic Brake Booster Assembly)
Controls the hydraulic pressure that is applied to the wheel cylinders during brake control.
Brake Booster Pump Assembly
(Built-into Hydraulic Brake Booster Assembly)
Draws up the brake fluid from the brake master cylinder reservoir and provides high hydraulic pressure to the brake booster accumulator assembly.
Skid Control ECU
Judges the vehicle driving condition based on signals from each sensor, and sends brake control signals to the hydraulic brake booster Assembly.
Four Wheel Drive Control ECU
Sends the transfer drive mode.
ECM
  1. Sends the throttle position signal, accelerator pedal position signal, engine speed signal etc., to the skid control ECU.
  2. Based on the signals received from the skid control ECU, controls the engine output.

HINT:
*1: Models without multi-terrain select
*2: Models with multi-terrain select
*3: Models with rear differential lock


OPERATING CONDITION
  1. The brake control function vary by the transfer drive mode as shown in the following table:

    2WD Models 
    Brake Control Function
    ABS
    EBD
    Brake Assist
    TRAC
    A-TRAC
    AUTO LSD
    VSC
    Hill-start
    Assist Control
    Downhill
    Assist Control
    CRAWL
    Trailer Sway Control
    ○
    ○
    ○
    ○
    X
    ○
    ○
    ○
    X
    X
    ○

    Models without Multi-terrain Select 
    Transfer
    Drive Mode
    Brake Control Function
    ABS
    EBD
    Brake Assist
    TRAC
    A-TRAC
    AUTO LSD
    VSC
    Hill-start
    Assist Control
    Downhill
    Assist Control
    CRAWL
    Trailer Sway Control
    H4F
    ○
    ○
    ○
    ○
    X
    X
    ○
    ○
    X
    X
    ○
    H4L
    ○
    ○
    ○
    ○
    X
    X
    ○
    ○
    X
    X
    ○
    L4L
    ○
    ○
    ○
    X
    ○
    X
    X
    ○
    ○
    X
    X

    HINT:
    ○: Operates
    X: Not operates


    Models with Multi-terrain Select 
    Transfer
    Drive Mode
    Brake Control Function
    ABS
    EBD
    Brake Assist
    TRAC
    A-TRAC
    AUTO LSD
    VSC
    Hill-start
    Assist Control
    Downhill
    Assist Control
    CRAWL
    Trailer Sway Control
    2WD
    ○
    ○
    ○
    ○
    X
    X
    ○
    ○
    X
    X
    ○
    H4L
    ○
    ○
    ○
    ○
    X
    X
    ○
    ○
    X
    X
    ○
    L4L
    ○
    ○
    ○
    X
    ○
    X
    X
    ○
    ○
    ○
    X
    Rear Diff.
    Lock On
    X
    X
    X
    X
    ○
    X
    X
    X
    ○
    ○
    X

    HINT:
    ○: Controls
    X: Not controls

  2. Hill-start assist control

    1. The hill-start assist control operates when all of the following conditions have been met:

      Hill-start Assist Control Operation Condition
      1. The shift lever is in D or S.
      2. The brake pedal is not depressed.
      3. The rear differential lock switch is off.
      4. The skid control ECU has detected the backward movement of the vehicle when the driver is starting off on a hill.

    2. The hill-start assist control stops operating when any of the following conditions have been met:

      Hill-start Assist Control Ending Condition
      1. The shift lever is in any position other than D or S.
      2. The brake pedal is depressed.
      3. The rear differential lock switch is on.
      4. Approximately 5 seconds have passed since control commenced.

  3. Downhill Assist Control

    1. The hill-start assist control operates when all of the following conditions have been met:

      Downhill Assist Control Operation Condition
      1. The downhill assist control switch is on
      2. The transfer drive mode is in L4L.
      3. The accelerator pedal and brake pedal is not depressed.
      4. Descending a hill at a vehicle speed of 25 km/h (16 mph) or less.

    2. The downhill assist control stops operating when any of the following conditions have been met:

      Downhill Assist Control Ending Condition
      1. The downhill assist control switch is off.
      2. The transfer drive mode is in any position other than L4L.
      3. The accelerator pedal or brake pedal is depressed.

  4. CRAWL

    1. When the CRAWL ON/OFF switch is on with all of the following conditions met, the CRAWL control starts operating.

      CRAWL Operation Condition
      1. The transfer drive mode is in L4L.
      2. The shift lever is in R, D or S.
      3. The driver's door is closed.

    2. The CRAWL control stops operating when any of the following conditions have been met:

      CRAWL Operation Ending Condition
      1. The CRAWL ON/OFF switch is off.
      2. The transfer drive mode is in any position other than L4L.
      3. The shift lever is in P or N.
      4. The driver's door is opened.
      5. Vehicle speed is above 25 km/h (16 mph).

  5. Multi-terrain Select

    1. When all of the following conditions are met, the multi-terrain select can be turned on or off and road mode can be selected by operating the multi-information switch, and the multi-terrain select indicator light will illuminate.

    2. If the drive mode most appropriate for the selected road mode is shifted to, the road mode will be displayed on the multi-terrain select indicator, and engine output control and A-TRAC control will commence.

      Multi-terrain Select Operation Condition
      1. The transfer drive mode is in L4L*.
      2. The CRAWL is off.

      HINT:
      If the "MUD & SAND" road mode is selected, the multi-terrain select will control when in transfer drive mode H4F, H4L or L4L.

    3. If the transfer drive mode is shifted to H4F or H4L while the multi-terrain select is controlling in "LOOSE ROCK", "MOGUL" or "ROCK" road mode, multi-terrain select control will halt temporarily and the multi-terrain select indicator light will flash.

    4. Multi-terrain select control will terminate if a malfunction occurs in the multi-information switch operation, the brake control system, the engine control system and the 4WD control system.

    5. The 2nd start switch and VSC OFF switch cannot be operated while multi-terrain select is in operation.


SYSTEM CONTROL

Control
Outline
Anti-lock Brake System (ABS)
The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
Multi-terrain Anti-lock Brake System
(Multi-terrain ABS)
In addition to the existing ABS function, the Multi-terrain ABS automatically calculates the optimum ABS control in accordance with the off-road situation such as a dirt or sandy road.
Electronic Brake Force distribution (EBD)
The EBD control utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle behavior.
Brake Assist
  1. The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping ensure the vehicle's braking performance.
  2. If the brake booster malfunctions and the skid control ECU judges that the brake pedal force applied by the driver is not sufficient to ensure adequate braking force, brake assist is used to enhance the braking force.
Traction Control (TRAC)
The TRAC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.
Active Traction Control (A-TRAC)
A-TRAC controls the brake hydraulic pressure that is applied to the slipping wheel, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an LSD effect.
AUTO LSD
Briefly pressing the VSC OFF switch in normal mode enters TRC OFF mode, allowing the AUTO LSD to operate. The AUTO LSD achieves a function equivalent to that of an LSD system through the use of the TRC. The AUTO LSD applies brake hydraulic pressure to a slipping wheel to reduce the difference in rotation speed between the left and right drive wheels. This causes driving torque to be transmitted to the wheel opposite the slipping wheel.
Vehicle Stability Control (VSC)
The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, such as may occur while cornering.
Hill-start Assist Control
Hill-start assist control detects the backward descent of the vehicle and effects 4-wheel hydraulic pressure control to reduce the backward speed of the vehicle. As a result, the vehicle can be started off on a hill more easily.
Downhill Assist Control
When the DAC switch is pressed with transfer drive mode in L4L, and without accelerator and brake pedals operation, downhill assist control activates to effect 4-wheel hydraulic pressure control, in order to maintain a constant low vehicle speed without causing the wheels to become locked. Thus, the vehicle can descend a steep hill in a stable manner.
CRAWL
When the vehicle runs on extremely bumpy rough ground or a slippery road, the CRAWL is activated to regulate the engine output and the hydraulic pressure of the 4 wheels, allowing the driver to drive the vehicle at the desired speed and keep that speed with virtually no accelerator or brake pedal operation. As a result, the off-road ground covering performance has been more improved.
Trailer Sway Control
The trailer sway control mitigates the phenomenon of the trailer sway by controlling the brakes and engine torque for each wheel when trailer sway phenomenon * is detected.
  1. * :Trailer sway is a phenomenon that occurs when the trailer swings side to side caused by crosswinds, steering, uneven road surfaces, etc., due to improper adjustment of torque load.


  1. Anti-lock Brake System (ABS)



    1. The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.


      X102062E01


      Text in Illustration (The illustration provides a conceptual image) 
      *A
      Models with ABS
      *B
      Models without ABS
      *a
      Brake Operation
      -
      -



  2. Multi-terrain Anti-lock Brake System (Multi-terrain ABS)

    1. While the multi-terrain select is operating in "MUD & SAND" road mode, this function detects the off-road driving in sand, mud, gravel, dirt and so on based on signals from the yaw rate sensor assembly, the speed sensor and the ECM, and then automatically switches to the ABS control most appropriate for the road condition.



    2. This function is intended to improve the braking feeling when driving off-road without negatively affecting on-road braking control performance.


      X102433E03


      X102434E02



  3. Electronic Brake Force Distribution (EBD)



    1. This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to ensure excellent braking performance.


      X102063E04


      X102064E04



    2. During cornering braking, this function controls the brake force that acts on the left and right wheels in accordance with the vehicle conditions at that time. This ensures vehicle stability and excellent braking performance.


      X102065


      Text in Illustration 
      V100136
      Control Moment
      V100135
      Brake Force



  4. Brake Assist



    1. In the brake assist, the skid control ECU calculates the speed and the amount of the brake pedal application based on the signals from the master cylinder pressure sensor and then determines the intention of the driver to make an emergency brake application. If the skid control ECU determines that the driver intends to make an emergency brake application, this function activates the hydraulic brake booster assembly to increase the brake fluid pressure, which increases the brake force.


      X104272E02



  5. Traction Control (TRAC)



    1. The TRAC helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. Simultaneously with the hydraulic brake control of the drive wheels, the skid control ECU makes a request to the ECM to effect engine output control. This produces the drive force that suits the driving conditions, in order to ensure the proper start-off acceleration.


      X102066E01


      Text in Illustration (Driving Condition on Road with Different Surface Friction Characteristics) 
      *A
      Models without TRAC
      *B
      Models with TRAC
      *1
      ECM
      - Engine Output Control
      *2
      Brake Actuator Assembly
      - Hydraulic Brake Control
      *a
      Brake Slipping Drive Wheel
      -
      -
      V100145
      Slippery Surface
      -
      -



  6. Active Traction Control (A-TRAC)

    1. When the vehicle drive mode is L4L*, the A-TRAC helps restrain wheelspin by controlling the brake hydraulic pressure that is applied to the spinning wheels, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an effect that is similar to Limited Slip Differential (LSD).

      HINT:
      *: When multi-terrain select is on (models with multi-terrain select)



    2. It independently controls the brake hydraulic pressure to the four wheels in accordance with the extent of the slippage at the wheels, as detected by the skid control ECU.


      X104274E04


      X102436E06



  7. AUTO LSD

    1. Briefly pressing the VSC OFF switch in normal mode allows the AUTO LSD to operate (TRAC OFF mode is selected). The AUTO LSD achieves the LSD effect by regulating the hydraulic pressure that acts on the drive wheels.

    2. TRAC enhances the start-off performance of the vehicle during low-grip surface conditions, such as snow or mud, by restricting the acceleration effort during a start-off, in order to help prevent the wheels from spinning.



    3. The AUTO LSD enhances the acceleration effort, in order to apply greater drive torque to the wheel that has grip. Thus, this function enables the vehicle to get unstuck if a wheel loses its grip, and enhances the vehicle's start-off performance when high-resistance surface conditions exist, such as loose gravel or sand.


      X104275E03


      X104276E03



  8. Vehicle Stability Control (VSC)



    1. The following are 2 examples that can be considered circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes at each wheel when the vehicle is under one of the conditions indicated below:


      X102067E01


      Text in Illustration 
      *a
      Front Wheel Skid Tendency (Understeer)
      - When the front wheels lose grip in relation to the rear wheel
      *b
      Rear Wheel Skid Tendency (Oversteer)
      - When the rear wheels lose grip in relation to the front wheels

    2. To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle yaw rate, and vehicle's lateral acceleration, which are then calculated by the skid control ECU.



    3. Whether or not the vehicle is experiencing a front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the target yaw rate (a target yaw rate is determined based on the vehicle speed and steering angle) that should be generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the target locus of travel. Thus, the skid control ECU determines that there is a large front wheel skid tendency.


      X102068E01


      Text in Illustration 
      *a
      Actual Locus of Travel (Actual Yaw Rate)
      *b
      Locus of Travel Based on the Target Yaw Rate



    4. Whether or not the vehicle is experiencing a rear wheel skid is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle is large, and the slip angular velocity is also large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.


      X102069E01


      Text in Illustration 
      *a
      Travel Direction of Vehicle's Center of Gravity
      *b
      Movement of Vehicle
      *c
      Slip Angle
      -
      Slip Angle

    5. When the skid control ECU determines that the vehicle exhibits a tendency to experience a front wheel skid or a rear wheel skid, it decreases the engine output and applies the brakes of the front or rear wheels to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.



    6. When the skid control ECU determines that there is a large front wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies the brakes of the rear wheel on the inner circle of the turn in order to help restrain the front wheel skid tendency.


      X102070


      Text in Illustration (Front Wheel Skid Dampening at Right Turn) 
      V100136
      Control Moment
      V100135
      Brake Force



    7. When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front and rear wheels of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured. In some cases, the skid control ECU applies the brake of the rear wheels, as necessary.


      X102071


      Text in Illustration 
      V100136
      Control Moment
      V100135
      Brake Force



  9. Hill-start Assist Control

    1. When the vehicle starts off on a steep or slippery hill, the vehicle may descend backward while the driver switches from the brake pedal to the accelerator pedal, thus making it difficult for the vehicle to start off. To prevent this from occurring, the hill-start assist control temporarily (approximately 5 seconds at the maximum) applies the brakes to the 4 wheels in order to prevent vehicle from descending backward.



    2. Without the hill-start assist control, the driver must quickly and precisely switch from the brake pedal to the accelerator pedal. With the hill-start assist control, however, the driver can start off easily and operate the pedal in a relaxed manner, because the hill-start assist control prevents the vehicle from descending backward.


      X102437E02



  10. Downhill Assist Control

    1. When the vehicle is descending a steep hill and the engine brake alone cannot provide a sufficient deceleration force while the transfer drive mode is in L4L, downhill assist control effects 4 wheels brake control to maintain a constant, low vehicle speed. Thus, the vehicle is able to descend in a stable manner without causing the wheels to become locked.

    2. When the vehicle descends a steep hill without downhill assist control, the driver must pay close attention to the brake and accelerator pedal maneuvers. However, with downhill assist control, the driver can concentrate on the steering operation, without accelerator and brake pedals operation.



    3. Downhill assist control enables the vehicle to maintain stability because it can descend a slippery hill at low speeds without causing the wheels to become locked.


      X102438E03



  11. CRAWL

    1. The CRAWL is a driving support system that regulates the engine output and the brake force, enabling the vehicle to be driven at a constant speed on rough ground or slippery roads.



    2. When the vehicle drives across rough grounds such as extremely bumpy rough roads, the driver needs to pay attention to the steering, braking and acceleration operations. However, with the CRAWL, the driver can concentrate on steering, without worrying about the accelerator pedal or brake pedal.


      X102439



    3. The CRAWL ensures good vehicle stability in situations such as when the vehicle is running on a slippery or steep road because the chances of the wheels spinning or locking are minimized by regulating the engine output and the brake force.


      X102440



  12. Trailer Sway Control

    NOTICE:
    1. Trailer sway control is a part of the VSC function. Accordingly, if the VSC OFF mode or VSC is not functioning normally, trailer sway control will not operate.
    2. Trailer sway control will be unable to stabilize the vehicle if a trailer is being towed which cannot be physically controlled due to the influence of the vehicle, road surface, driving conditions and so on.




    1. If the vehicle is towing a trailer with an inappropriate hitch load, trailer sway could be caused by crosswinds, imbalance caused by load, or the driver's steering. Trailer sway control reduces trailer sway by controlling the engine output and the braking of each wheel.


      X114504E01

    2. The skid control ECU detects the occurrence of trailer sway based on signals from the yaw rate & deceleration sensor and the steering angle sensor.

    3. Trailer sway can be reduced by decelerating the vehicle. When the skid control ECU detects trailer sway, it controls the brakes of each wheel while simultaneously requesting engine output control from the ECM and reducing vehicle speed.

    4. Moreover, by using brake control to reduce the yaw moment caused by trailer sway, trailer sway can be reduced more quickly than by simply decelerating the vehicle.



    5. The slip indicator light on the combination meter flashes when trailer sway control is in operation. Also, the stop light illuminates to inform vehicles behind that the vehicle is decelerating.


      X114505E01


      X114506E01


FUNCTION


  1. VSC OFF Switch



    1. The operation of the VSC and TRAC functions can be stopped by the VSC OFF switch. While the vehicle is running off the shoulder of the road or running on a dirt road, the engine output control is stopped to maintain drive torque.

      HINT:
      The VSC OFF switch cannot be operated while multi-terrain select is operating.


      X114522E01


      Text in Illustration 
      *1
      Combination Meter Assembly
      *2
      VSC OFF Switch
      *a
      VSC OFF Indicator Light
      *b
      TRAC OFF Indicator Light

    2. The VSC OFF switch can select 3 modes (mode A, mode B, and mode C).

    3. Briefly pressing the VSC OFF switch in mode A selects the mode B.

    4. Pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped selects the mode C.

    5. Briefly pressing the VSC OFF switch in the mode B or mode C or turning the ignition switch off returns to the mode A.

    6. When TRAC is not operating, the TRAC OFF indicator light will illuminate.



    7. When VSC is not operating, the VSC OFF indicator light will illuminate.


      X102072E03


      Function of VSC OFF Switch (Models without Multi-terrain Select) 
      Transfer Drive Mode
      Brake Control Function
      VSC OFF Switch Mode
      Mode A
      Mode B
      Mode C
      H4F
      TRAC
      Operates
      Not Operates
      Not Operates
      A-TRAC
      Not Operates
      Not Operates
      Not Operates
      VSC
      Operates
      Operates
      Not Operates
      H4L
      TRAC
      Operates
      Not Operates
      Not Operates
      A-TRAC
      Not Operates
      Not Operates
      Not Operates
      VSC
      Operates
      Operates
      Not Operates
      L4L
      TRAC
      Not Operates
      -
      Not Operates
      A-TRAC
      Operates
      -
      Not Operates
      VSC
      Not Operates
      -
      Not Operates

      Function of VSC OFF Switch (Models with Multi-terrain Select) 
      Transfer Drive Mode
      Brake Control Function
      VSC OFF Switch Mode
      Mode A
      Mode B
      Mode C
      H4F
      TRAC
      Operates
      Not Operates
      Not Operates
      A-TRAC
      Not Operates
      Not Operates
      Not Operates
      VSC
      Operates
      Operates
      Not Operates
      H4L
      TRAC
      Operates
      Not Operates
      Not Operates
      A-TRAC
      Not Operates
      Not Operates
      Not Operates
      VSC
      Operates
      Operates
      Not Operates
      L4L
      TRAC
      Not Operates
      -
      -
      A-TRAC
      Not Operates
      -
      -
      VSC
      Not Operates
      -
      Not Operates



  2. Multi-terrain Select

    1. The multi-terrain select has the following functions:

      Multi-terrain Select Function
      Sends the road mode that is selected by Multi-terrain Select Mode Selector switch to the skid control ECU, ECM and four wheel drive control ECU.
      Automatically switches the optimum engine output control and the brake control function to A-TRAC when the selected road mode and transfer drive mode are switched to the optimum position.



    2. 4 road modes can be selected: "MUD & SAND", "LOOSE ROCK", "MOGUL" and "ROCK". The recommended road modes for each road condition are listed below.

      HINT:
      Road mode recommendations are for reference only. The mode may not be appropriate depending on the road condition (incline, road surface, road undulation).


      X102338E01


      X102470E02

    3. The engine output and A-TRAC control tendency for each road mode are as follows:

      Multi-terrain Select
      Road Mode
      Transfer Drive Mode
      Control Tendency
      Engine Control
      A-TRAC Control
      MUD and SAND
      H4F, H4L, L4L
      Engine output control is performed gradually in response to accelerator pedal operation
      The wheel is allowed to slip more than usual
      LOOSE ROCK
      L4L
      Engine output control is performed gradually in response to accelerator pedal operation
      The wheel is allowed to slip more than usual
      MOGUL
      L4L
      Engine output control is performed gradually in response to accelerator pedal operation
      The wheel is made to grip more than usual
      ROCK
      L4L
      Engine output control is performed gradually in response to accelerator pedal operation
      The wheel is made to grip more than usual


CONSTRUCTION


  1. Yaw Rate and Acceleration Sensor

    1. This sensor has a built-in deceleration sensor.

    2. The yaw rate sensor detects the vehicle's yaw rate.



    3. The deceleration sensor detects the vehicle's longitudinal and lateral acceleration


      X102074E01


      Text in Illustration 
      *1
      Yaw Rate and Acceleration Sensor
      *2
      Deceleration Sensor
      *3
      Yaw Rate Sensor
      -
      -
      *a
      Cross Section
      -
      -



  2. Steering Angle Sensor



    1. The steering angle sensor detects the steering direction and angle, and sends this signal to the skid control ECU.


      X102075



  3. Speed Sensor

    1. Active type speed sensors, which can detect the rotational direction of the wheel, have been provided. This sensor contains 2 Magnetic Resistance Elements (MREs).



    2. The magnet type rotor, which consists of N and S poles that are arranged in a circle, is integrated with the hub bearing inner race.


      X102443E01


      Text in Illustration 
      *1
      Front Speed Sensor
      *2
      Sensor Rotor
      *3
      Rear Speed Sensor
      -
      -
      *a
      Front Axle
      *b
      Rear Axle



  4. Hydraulic Brake Booster Assembly

    1. The brake actuator portion in hydraulic brake booster consists of 4 switching solenoid valves, 8 control solenoid valves and skid control ECU.

    2. The pressure increase mode, the pressure holding mode, and the pressure reduction mode are effected based on the combination of these solenoid valves that are turned on and off, in order to control the hydraulic pressure that is applied to each of the wheel cylinders.

    3. 4 switching solenoid valves are used: 2 (SMCF, SREA) in the front brake fluid path, 1 (SREC) in the rear brake fluid path, and 1 (STR) in the accumulator fluid path. The switching solenoid valves open and closed in accordance with the control signals from the skid control ECU in order to switch the respective brake fluid path.



    4. 8 control solenoid valves are used for the 4 wheels (2 types per wheel: pressure holding solenoid and pressure reduction solenoid).


      X102444


      X102445E01


      Text in Illustration 
      *1
      STR (Traction Solenoid Valve)
      *2
      SREC (Regulator Cut Solenoid Valve)
      *3
      SREA
      (Regulator Apply for Front Solenoid Valve)
      *4
      SMCF (Master Cut for Front Solenoid Valve)
      *5
      Master Cylinder Pressure Sensor
      *6
      SH (Pressure Holding Solenoid Valve)
      *7
      SH (Pressure Holding Solenoid Valve)
      *8
      SH (Pressure Holding Solenoid Valve)
      *9
      SH (Pressure Holding Solenoid Valve)
      *10
      SR (Pressure Holding Solenoid Valve)
      *11
      SR (Pressure Holding Solenoid Valve)
      *12
      SR (Pressure Holding Solenoid Valve)
      *13
      SR (Pressure Holding Solenoid Valve)
      -
      -
      *a
      Rear LH
      *b
      Rear RH
      *c
      Front LH
      *d
      Front RH
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder
      -
      -


OPERATION


  1. Speed Sensor



    1. The active type speed sensor uses 2 Magnetic Resistance Elements (MREs) to detect magnetic field changes caused when the sensor rotor rotates, and the speed sensor outputs the detected information to the skid control ECU as digital pulses.


      X115307E01

    2. To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by the 2 Magnetic Resistance Elements (MREs).



    3. Upon receiving this signal, the speed sensor outputs a forward or backward wave.


      X102079E01


      X102080E01



    4. To detect the vehicle speed, the frequency of the output pulses is used. Because the active type sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.


      X102081E01



  2. ABS and EBD

    1. Based on the signals received from the 4 speed sensors, the skid control ECU calculates the speed of each wheel, and checks wheel slipping conditions.

    2. The skid control ECU compares the speed sensor signals of the front and rear, judges the slipping condition of the rear wheel, and operates the EBD.



    3. When a wheel is about to lock, the ABS operation starts in order to regulate the hydraulic pressure at the wheel cylinders while switching between the 3 modes: pressure increase, pressure holding, and pressure reduction.


      X104273E03


      X102447E01


      EBD Operation 
      Item
      EBD Not Activated
      EBD Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *2
      SREC
      Off (Open)
      Off (Open)
      Off (Open)
      Off (Open)
      *3
      SREA
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *4
      SMCF
      Off (Open)
      Off (Open)
      Off (Open)
      Off (Open)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *d
      Wheel Cylinder Pressure
      -
      -
      -
      -
      Rear Brake LH
      *5
      SH
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *a
      Wheel Cylinder Pressure
      -
      -
      -
      -
      Rear Brake RH
      *6
      SH
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *b
      Wheel Cylinder Pressure
      -
      -
      -
      -
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder

      X102448E01


      ABS Operation 
      Item
      ABS Not Activated
      ABS Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *2
      SREC
      Off (Open)
      Off (Open)
      Off (Open)
      Off (Open)
      *3
      SREA
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *4
      SMCF
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Open)
      *d
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder

      HINT:
      While the front wheels are in the ABS operation, SREA and SMCF are on. While only rear wheels are in the ABS operation, SREA and SMCF are off.



  3. Multi-terrain ABS

    1. The skid control ECU calculates speed and deceleration of each wheel, and checks wheel slipping condition based on signals from 4 speed sensors and yaw rate sensor assembly as well as the engine output information transmitted from the ECM.



    2. If the wheel is likely to be locked, the skid control ECU controls the pressure holding solenoid valve and pressure reduction solenoid valve as multi-terrain ABS operation in the following 3 modes: increase mode, holding mode, and reduction mode.


      X104277E02


      X102448E01


      Multi-terrain ABS Operation 
      Item
      Multi-terrain ABS Not Activated
      Multi-terrain ABS Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *2
      SREC
      Off (Open)
      Off (Open)
      Off (Open)
      Off (Open)
      *3
      SREA
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *4
      SMCF
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *d
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder

      HINT:
      1. While the front wheels are in the multi-terrain ABS operation, SREA and SMCF are on.
      2. While only rear wheels are in the multi-terrain ABS operation, SREA and SMCF are off.



  4. Brake Assist



    1. If an emergency braking situation has occurred, it is detected by the skid control ECU based on the vehicle speed signal from the speed sensor, the brake pedal application speed from the master cylinder pressure sensor, and the signal representing the amount of pedal effort. Then, the skid control ECU actuates each solenoid valve. As a result, the pressure from the brake booster accumulator assembly is applied to the wheel cylinders. The accumulator pressure that is applied to the wheel cylinders generates a higher pressure than the master cylinder.


      X104278E04


      X102461E01


      Brake Assist Operation 
      Item
      Brake Assist Not Activated
      Brake Assist Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      On (Open)
      On (Open)
      Off (Closed)
      *2
      SREC
      Off (Open)
      On (Closed)
      On (Closed)
      Off (Open)
      *3
      SREA
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *4
      SMCF
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *d
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder



  5. TRAC

    1. The fluid pressure that is generated by the brake booster pump assembly is regulated by the switching solenoid valves and control solenoid valves to the required pressure. Thus, the pressure to the wheel cylinders of the drive wheels is controlled in the following 3 modes: increase mode, holding mode, and reduction mode, to restrain the slippage of the drive wheels.

    2. The skid control ECU outputs a TRAC operation signal to the ECM. Upon receiving this signal, the ECM effects engine output control.



    3. If the accumulator pressure drops during this operation, the skid control ECU receives the signals from the accumulator pressure sensor and actuates the brake booster pump assembly to ensure the proper accumulator pressure.


      X104279E02


      X102461E01


      TRAC Operation 
      Item
      TRC Not Activated
      TRAC Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      On (Open)
      On (Open)
      Off (Closed)
      *2
      SREC
      Off (Open)
      On (Closed)
      On (Closed)
      Off (Open)
      *3
      SREA
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *4
      SMCF
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *d
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder



  6. A-TRAC

    1. Based on the vehicle speed that has been calculated from each speed sensor and signals of the yaw rate and deceleration sensor, the skid control ECU computes the target control speed.



    2. The skid control ECU compares the target control speed and the speed of the wheels to determine whether or not slippage exists. Upon detecting slippage, the skid control ECU controls the solenoid valve of the hydraulic brake booster assembly to control the brake fluid pressure that is applied to the slipping wheel. When the wheel speed becomes lower than the target control speed, the skid control ECU stops increasing the brake fluid pressure.


      X114933E01



    3. The fluid pressure control of the A-TRAC independently controls the brake of each wheel by operating the individual solenoid valves in accordance with the signals received from the skid control ECU. The brake of each wheel is controlled in the following three modes: pressure reduction, pressure hold, and pressure increase modes.


      X102461E01


      A-TRAC Operation 
      Item
      A-TRC Not Activated
      A-TRAC Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      On (Open)
      On (Open)
      Off (Closed)
      *2
      SREC
      Off (Open)
      On (Closed)
      On (Closed)
      Off (Open)
      *3
      SREA
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *4
      SMCF
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *d
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder



  7. AUTO LSD

    1. AUTO LSD is a function that has effects similar to a mechanical type LSD. AUTO LSD employs the TRAC to control brake hydraulic pressure and engine output.



    2. The Skid Control ECU detects slippage that occurs as a result of a rotational difference between the drive wheel and the non-driven wheel. Via the TRAC, the AUTO LSD detects the wheel slip that occurs (the wheel that is rotating faster) , based on the rotational difference of the right and left drive wheels, and puts AUTO LSD into action.


      X114985E01


      X103121E01


      AUTO LSD Operation 
      Item
      AUTO LSD
      Not Activated
      AUTO LSD Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      *2
      SREC
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *3
      SREA
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *4
      SMCF
      Off (Open)
      Off (Open)
      Off (Open)
      Off (Open)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      Off (Open)
      Off (Open)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *c
      Wheel Cylinder Pressure
      -
      -
      -
      -
      Front Brake RH
      *8
      SH
      Off (Open)
      Off (Open)
      Off (Open)
      Off (Open)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *e
      Wheel Cylinder Pressure
      -
      -
      -
      -
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder



  8. VSC

    1. Based on the information provided by various sensors, switches, and the ECM, the skid control ECU determines the vehicle's yaw moment. Then, the skid control ECU controls the fluid pressure that is generated by the brake booster pump assembly and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes. As a result, the tendency of the front wheels or the rear wheels to skid is restrained.



    2. At this time, the skid control ECU outputs a VSC operation signal to the ECM and the combination meter assembly. Upon receiving this signal, the ECM controls the engine output. The slip indicator light will blink in the combination meter assembly.


      X114986E01



    3. During front wheel skid restraining control, the brakes of the rear wheels and front wheel of the outer side of the turn are applied. Also, depending on whether the brake is on or off and on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it restrains a front wheel skid while the vehicle is making a right turn.


      X102458E01


      VSC Operation (Turning Right) 
      Item
      VSC Not Activated
      VSC Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      On (Open)
      On (Open)
      Off (Closed)
      *2
      SREC
      Off (Open)
      On (Closed)
      On (Closed)
      Off (Open)
      *3
      SREA
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *4
      SMCF
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *d
      Wheel Cylinder Pressure
      -
      -
      -
      -
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder



    4. During rear wheel skid restraining control, the front wheel brake of the outer side of the turn is applied. Also, depending on whether the brake is on or off and on the condition of the vehicle, there are circumstances in which the brake might be applied to the rear brake of the outer side of the turn. The diagram below shows the hydraulic circuit in the pressure increase mode, as it restrains a rear wheel skid while the vehicle is making a right turn.


      X102459E01


      VSC Operation (Turning Right) 
      Item
      VSC Not Activated
      VSC Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      On (Open)
      On (Open)
      Off (Closed)
      *2
      SREC
      Off (Open)
      On (Closed)
      On (Closed)
      Off (Open)
      *3
      SREA
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *4
      SMCF
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      Off (Closed)
      *d
      Wheel Cylinder Pressure
      -
      -
      -
      -
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      -
      -
      -
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      Off (Open)
      Off (Open)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder



  9. Hill-start Assist Control

    1. Based on the information provided by various sensors, switches, and the ECM, the skid control ECU computes the backward movement of the vehicle that occurs when the vehicle starts off on a hill. Then, the skid control ECU controls the fluid pressure that is generated by the pump and pump motor and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.

    2. The skid control ECU determines the state of the backward movement of the vehicle while the driver is attempting to drive uphill, based on the speed sensors and the neutral start switch.

    3. The skid control ECU determines the gradient of the hill, the acceleration state of the vehicle, the locked state and the rotation direction of each wheel through the speed sensors and the yaw rate sensor assembly. Then, the skid ECU computes the amount of brake control that will prevent the wheels from locking.

    4. During this operation, the skid control ECU outputs a hill-start assist control operation signal to the combination meter. This causes the slip indicator light to blink, sends signals to the stop light control relay which turns on the stop light.



    5. The hill-start assist control operates for approximately five seconds. At this time, the skid control ECU informs the driver by the slow and intermittent sound of the buzzer in the combination meter assembly. After this, the skid control ECU alerts the driver by using the quick and intermittent sound of the buzzer in the combination meter assembly, and gradually releases the brake hydraulic pressure in order to end the hill-start assist control operation.


      X114510E02


      X102461E01


      Hill-start Assist Control Operation 
      Item
      Hill-start Assist Control Not Activated
      Hill-start Assist Control Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      On (Open)
      On (Open)
      Off (Closed)
      *2
      SREC
      Off (Open)
      On (Closed)
      On (Closed)
      Off (Open)
      *3
      SREA
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *4
      SMCF
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *d
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder



  10. Downhill Assist Control

    1. Based on the information provided by various sensors, switches, and the engine ECU, the skid control ECU determines the conditions that enable downhill assist control operation. Then, the skid control ECU controls the fluid pressure that is generated by the brake booster pump assembly and applies it by way of the solenoid valve to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding and pressure reduction modes.

    2. The skid control ECU computes the vehicle speed, travel direction, and the gradient of the hill in accordance with the signals that are input by the speed sensor and the yaw rate sensor assembly, and effects brake control to attain the target vehicle speed. The target vehicle speed is determined by the direction of the vehicle.

      Downhill Assist Control Target Vehicle Speed 
      Travel Direction
      Forward
      5 to 7 km/h (3 to 4 mph)
      Backward
      3 to 5 km/h (2 to 3 mph)



    3. During the downhill assist control operation, the skid control ECU outputs signals to the stop light control relay to cause the stop light to turn on, and to the combination meter to cause the slip indicator light to blink.


      X114511E02


      X102461E01


      Downhill Assist Control Operation 
      Item
      Downhill Assist Control Not Activated
      Downhill Assist Control Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      On (Open)
      On (Open)
      Off (Closed)
      *2
      SREC
      Off (Open)
      On (Closed)
      On (Closed)
      Off (Open)
      *3
      SREA
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *4
      SMCF
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *d
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder



  11. CRAWL

    1. Based on the information provided by various sensors, switches, and the ECM, the skid control ECU determines the conditions that enable the CRAWL to operate. The skid control ECU computes the target vehicle speed (approximately 1 to 6 km/h, 1 to 3.7 mph) to control the vehicle speed, and the target wheel speeds to control the wheel slipping. The target vehicle speed can be changed using the CRAWL speed selector switch.



    2. When the vehicle speed differs from the target speed, the engine output is regulated. When the wheel speeds differ from the target speeds, the hydraulic brake pressure of the wheels is regulated.


      X114512E02



    3. The skid control ECU controls the fluid pressure that is generated by the brake booster pump assembly and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.


      X102461E03


      CRAWL Operation 
      Item
      CRAWL Not Activated
      CRAWL Activated
      Increase Mode
      Holding Mode
      Reduction Mode
      Switching Solenoid Valve
      *1
      STR
      Off (Closed)
      On (Open)
      On (Open)
      Off (Closed)
      *2
      SREC
      Off (Open)
      On (Closed)
      On (Closed)
      Off (Open)
      *3
      SREA
      Off (Closed)
      On (Open)
      On (Open)
      On (Open)
      *4
      SMCF
      Off (Open)
      On (Closed)
      On (Closed)
      On (Closed)
      Control Solenoid Valve
      Front Brake LH
      *7
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *11
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *c
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Front Brake RH
      *8
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *12
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *d
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake LH
      *5
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *9
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *a
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      Rear Brake RH
      *6
      SH
      Off (Open)
      Off (Open)
      On (Closed)
      On (Closed)
      *10
      SR
      Off (Closed)
      Off (Closed)
      Off (Closed)
      On (Open)
      *b
      Wheel Cylinder Pressure
      -
      Increases
      Holds
      Reduces
      V100135
      To Brake Master Cylinder Reservoir
      V100136
      From Brake Booster Accumulator Assembly
      V100137
      From Brake Master Cylinder


FAIL-SAFE
  1. If a failure occurs in the skid control ECU, sensors, or brake actuator, the system continues effecting brake control by excluding the failed area and using only the areas that are operating normally.


DIAGNOSIS
  1. If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.

  2. This system has a sensor signal check (test mode) function.

  3. For details of DTC and check function, refer to the 2014 4RUNNER Repair Manual (Pub. No. RM23V0U).