AIR CONDITIONING SYSTEM > GENERAL



OUTLINE
  1. 2 types of air conditioning system are used, manual and automatic.

  2. The automatic air conditioning system uses left and right independent temperature control to enhance comfort.


SPECIFICATION
  1. Performance

    Heater
    Heater Output
    W
    5750
    Air Flow Volume
    m3/h
    350
    Power Consumption
    W
    250
    Cooler
    Cooling Capacity
    W
    5770
    Air Flow Volume
    m3/h
    540
    Power Consumption
    W
    300

  2. Ventilation and Heater Core

    Heater Radiator Unit Sub-assembly
    Type
    Straight Flow Aluminum (SFA) -II
    Size W x H x L
    mm (in.)
    243.2 x 140 x 27
    (9.6 x 5.5 x 1.1)
    Fin Pitch
    mm (in.)
    1.5 (0.06)
    Blower Motor
    Motor Type
    K70-BMM
    Fan Type
    Semi Sirocco
    Fan Size (Dia. x H)
    mm (in.)
    165 x 70 (6.5 x 2.8)

  3. Air Conditioning

    Cooler Condenser Assembly
    Type
    Multi-Flow (MF)-IV
    Size W x H x L
    mm (in.)
    600 x 491.8 x 16 (23.6 x 19.4x 0.6)
    Fin Pitch
    mm (in.)
    3.15 (0.12)
    Air Conditioning Compressor (Compressor and Magnetic Clutch)
    Type
    10S17C
    Pulley
    Steel with Magnetic Clutch
    Oil Volume
    cc
    120 to 135
    Refrigerant
    Type
    HFC 134a
    Charge Volume
    g
    520 to 580
    Evaporator
    Type
    Revolutionary super-slim Structure (RS)
    Size W x H x L
    mm (in.)
    252.9 x 231 x 38
    (10.0 x 9.1 x 1.5)
    Fin Pitch
    mm (in.)
    2.6 (0.10)


MAIN FEATURES
  1. The manual and automatic air conditioning system has the following features:

    Features
    Outline
    Air Conditioning Type
    Manual
    Automatic
    High Performance
    Neural network control is used so passengers can finely control the air conditioning for maximum comfort.
    -
    ○
    Air outlet from console for the rear seat is installed to blow air and ensure excellent air conditioning performance.
    ○
    ○
    A pollen-removal type clean air filter, which has a pollen-removal effect, is used.
    ○
    ○
    The blower control has 7 levels to allow precise control.
    ○
    -
    The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control.
    -
    ○
    The left and right independent temperature controls ensure further comfort.
    -
    ○
    A MAX A/C setting is provided on the temperature control switch to improve cooling efficiency.
    ○
    -
    Lightweight
    A Bus connector with a built-in IC is used in a lightweight wire harness design to allow a reduced number of wires.
    ○
    ○
    The use of this connector means that pulse pattern type servo motors are used.
    ○
    ○
    Compact
    A blower motor with a built-in blower motor controller is used in a compact construction.
    ○
    ○
    Others
    The following parts are used to ensure high cooling performance while realizing a compact and lightweight construction.
    1. Semi-center location air conditioning unit
    2. Revolutionary super-slim Structure (RS) evaporator
    3. Straight Flow Aluminum (SFA)-II heater radiator unit sub-assembly
    4. Multi-Flow (MF)-IV sub-cool cooler condenser assembly
    ○
    ○