SMART KEY SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components for the start function have the following functions:

    Component
    Function
    Engine Switch
    1. Transponder Key Amplifier
    1. Transmits the engine switch signal to the power management control ECU.
    2. Informs the driver of any power source or system abnormality through the illumination stage of the indicator light.
    3. Receives the ID code and transmits it to the certification ECU (smart key ECU assembly) when the key battery is too weak to respond to the tuner based on the signals from the room oscillators.
    Key
    Receives the signals from the oscillators and returns the ID code to the door control receiver.
    Indoor Electrical Key Oscillator
    1. Front, Center, Rear
    Receives a request signal from the certification ECU (smart key ECU assembly) and forms the actuation area in the vehicle interior.
    Door Control Receiver
    Receives the ID code from the key and transmits it to the certification ECU (smart key ECU assembly).
    Power Management Control ECU
    1. Switches the power source ("engine switch") among four modes (off, on (ACC), on (IG), start) in accordance with the shift position and the brake pedal signal.
    2. Turns on the ST relay, and starts the engine when the engine switch is pushed once with the brake pedal depressed.
    3. Controls the smart key system start in accordance with the signals received from the switches and each ECU.
    Certification ECU (Smart Key ECU Assembly)
    1. Certifies the ID code received from the door control receiver and transmits the certification results to the ID code box (immobiliser code ECU) and steering lock ECU.
    2. Transmits the steering lock/unlock signals.
    3. Transmits the engine immobiliser set/unset request signals.
    ID Code Box (Immobiliser Code ECU)
    Receives the steering unlock or engine immobiliser set/unset request signals from the certification ECU (smart key ECU assembly), certifies them, and transmits each set/unset request signal to the steering lock ECU or ECM.
    Stop Light Switch
    Outputs the state of the brake pedal to the power management control ECU.
    Park/Neutral Position Switch
    Outputs the shift position signal to the power management control ECU.
    Steering Lock ECU
    Receives the steering unlock/lock request signal from the ID code box (immobiliser code ECU), and activates the steering lock motor.
    ECM
    Receives the signal from the ID code box (immobiliser code ECU) and performs engine ignition and injection.
    Combination Meter Assembly
    1. Key Warning Light
    2. Buzzer
    Sounds the buzzer and illuminates the key warning light according to the activation signal from the certification ECU (smart key ECU assembly).

  2. The main components in the entry function have the following functions:

    Component
    Function
    Key
    1. Outputs information such as the key ID and vehicle ID when request signals that are output by the room and door oscillators are received.
    2. Outputs a request signal when the lock, unlock or panic button on the key is pushed.
    3. Outputs information such as the key ID and vehicle ID when the radio wave that is output by the transponder key amplifier in the engine switch is received.
    4. Has an integrated mechanical key that can be used to unlock the doors when the key battery is weak.
    Main Body ECU (Multiplex Network Body ECU)
    1. Receives a request signal from the certification ECU (smart key ECU assembly) and actuates the door lock motors to unlock or lock all the doors.
    2. Transmits the condition of each door and the back door to the certification ECU (smart key ECU assembly).
    Certification ECU (Smart Key ECU Assembly)
    1. Certifies the ID code received from the door control receiver and transmits the certification results to the steering lock ECU.
    2. Controls the oscillators and touch sensors.
    3. Transmits the door lock/unlock request signals during the entry function.
    Outside Door Handle
    Door Oscillator
    Receives a request signals from the certification ECU (smart key ECU assembly), and creates an actuation area around each front door.
    Lock Sensor
    Transmits door lock request signals to the certification ECU (smart key ECU assembly).
    Touch Sensor
    Detects when a person touches the inside of an outer door handle.
    Outside Electrical Key Oscillator
    Receives a request signal from the certification ECU (smart key ECU assembly), and forms an actuation area around the back door.
    Indoor Electrical Key Oscillator
    1. Front, Center, Rear
    Receives a request signal from the certification ECU (smart key ECU assembly) and forms the actuation area in the vehicle interior.
    Door Control Receiver
    Receives the ID code from the key and transmits it to the certification ECU (smart key ECU assembly).
    Combination Meter Assembly
    1. Key Warning Light
    2. Buzzer
    Sounds the buzzer and illuminates the key warning light according to the activation signal from the certification ECU (smart key ECU assembly).
    Luggage Electrical Key Switch
    1. Back Door Unlock Switch
    2. Back Door Lock Switch
    Transmits a back door lock/unlock request signal to the back door ECU (multiplex network door ECU).
    Back Door Opener Switch
    Transmits a back door unlock request signal to the back door ECU (multiplex network door ECU).
    Back Door ECU (Multiplex Network Door ECU)
    Transmits a back door lock/unlock request signal to the main body ECU (multiplex network body ECU).
    Wireless Door Lock Buzzer
    1. Sounds as an answer back for entry lock/unlock and wireless lock/unlock to inform the driver.
    2. Sounds to inform the driver of malfunctions in the smart key system with.


OPERATION
  1. The special functions of the smart key system only work when the key is in the actuation area formed by the 6 oscillators.

  2. The indoor electrical key oscillator (front), indoor electrical key oscillator (center), and indoor electrical key oscillator (rear) form the interior actuation area.



  3. The door electrical key oscillator LH, door electrical key oscillator RH, and outside electrical key oscillator form the exterior actuation area.


    Y104253E02


    Text in Illustration 
    *1
    Key
    *2
    Indoor Electrical Key Oscillator (Front)
    *3
    Door Electrical Key Oscillator LH
    *4
    Door Electrical Key Oscillator RH
    *5
    Indoor Electrical Key Oscillator (Center)
    *6
    Indoor Electrical Key Oscillator (Rear)
    *7
    Outside Electrical Key Oscillator (Back Door)
    -
    -
    *a
    Approximately 0.7 to 1.0 m (2.3 to 3.3 ft.)
    -
    -
    V100144
    Interior Actuation Area
    V100145
    Exterior Actuation Area

    Actuation Area
    Detail
    Interior
    The interior actuation area of the indoor electrical key oscillators (front, center, rear) is formed when the driver door is opened or closed, when the engine switch is pushed, when a warning is activated, or when the lock sensor is on.
    Exterior
    The exterior actuation area formed by the door electrical key oscillators (LH and RH) and outside electrical key oscillator (back door) is approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) from the outside handle of the front doors, or the center of the rear bumper.
    Around Front Doors
    The exterior actuation area of the door electrical key oscillators (LH, RH) is formed by transmitting a request signal every 0.25 seconds while the engine switch is off and each door is locked. In this way it detects the presence of a key. When locking the door using the lock sensor on the outer door handle, the actuation area is formed when the lock sensor is touched.
    Around Back Door
    The exterior actuation area of the outside electrical key oscillator (back door) is formed when the back door opener switch or back door unlock switch is on.


FUNCTION
  1. Cranking Hold Function

    1. When the engine switch is pushed with the brake pedal depressed, the power management control ECU receives a start signal. When the power management control ECU receives this signal, in order to operate the starter, the power management control ECU sends power from its STAR terminal to the starter relay. The power is sent via the park/neutral position switch when the shift lever is in either P or N. At this time, the power management control ECU turns off the ACC relay by turning off the power sent from the ACCD terminal. The ACC relay is turned off to prevent flickering of the meters, clock and audio system.

    2. While cranking, the power management control ECU continues energizing the starter relay until it is determined that the engine has started. The power management control ECU and ECM are both used to judge if the engine has started. When it has been judged that the engine has started, the power management control ECU stops energizing the starter relay.

    3. Cranking hold time and the engine speed used to judge that the engine has started are determined by the power management control ECU according to the engine coolant temperature.

    4. If the engine does not start, the starter operates for a length of time that is based on coolant temperature.

    5. This system has following safety features:

      1. While the engine is running, the starter cannot operate.
      2. The starter will stop operating once the engine has started, even if the engine switch remains pushed.
      3. Starter operation is limited to a maximum of 30 seconds to protect the starter motor.

      4. The starter will stop if the ECM cannot detect an engine speed signal (NE) while the starter is operating.


        Y104847E01


SYSTEM CONTROL


  1. Start Function



    1. The start function has different power source patterns to suit the brake pedal state and shift lever position.

      Pattern
      Brake Pedal
      Shift Lever
      Power Source Pattern
      A
      Depressed
      P or N
      When the engine switch is pushed once.
      1. Off → engine start
      B
      Not Depressed
      P
      Each time the engine switch is pushed.
      1. Off → on (ACC) → on (IG) → off
      C
      Except P
      Each time the engine switch is pushed.
      1. Off → on (ACC) → on (IG) → on (ACC)
      D
      -
      P
      When the engine switch is pushed in the on (IG) condition.
      1. On (IG) (engine is started or not started) → off
      E
      -
      Except P
      When the engine switch is pushed in the on (IG) condition.
      1. On (IG) (engine is started or not started) → on (ACC)


      B330135E02

      NOTICE:
      1. Normally, the operation of the engine switch is disabled while the vehicle is being driven. However, in an emergency, by pushing the engine switch for approximately 2 seconds or more or pushing the engine switch 3 times or more in a row, the driver can stop the engine while the vehicle is in motion.
      2. If no signals are transmitted to the power management control ECU due to malfunctions in the stop light switch or park/neutral position switch, the engine may not start when the engine switch is pushed with the brake pedal depressed. In such cases, performing the following procedure may enable the engine to start: 1) push the engine switch to turn the power source from off to on (ACC), and 2) push the engine switch again and hold it for 15 seconds or more.
      3. The above 2 operations must be applied only in emergency situations. Under normal conditions, the engine must not be stopped by pushing the engine switch while driving or should not be started without depressing the brake pedal or when the shift lever is in any position except P or N.



    2. Pattern A: Off → Engine start

      Step
      System Operation
      (1)
      The driver, carrying the key, enters the vehicle.
      (2)
      When the brake pedal is depressed with the following conditions satisfied, the power management control ECU recognizes the stop light switch signal and transmits the key certification request to the certification ECU (smart key ECU assembly):
      1. Shift lever is in P or N.
      2. The power source is off.
      (3)
      The certification ECU (smart key ECU assembly) receives the certification request and transmits a request signal to the oscillators (front, center, rear). These oscillators then form an actuation area.
      (4)
      The moment the key receives the request signal, it transmits its ID code to the door control receiver. The signal includes the response code.
      (5)
      The door control receiver receives this code and transmits it to the certification ECU (smart key ECU assembly).
      (6)
      The certification ECU (smart key ECU assembly) judges and certifies the ID code, and transmits a key certification OK signal to the power management control ECU.
      (7)
      Due to the brake pedal being depressed, the power management control ECU turns on the green indicator light of the engine switch.
      (8)
      The driver pushes the engine switch once, while the green indicator light of the engine switch is illuminated.


      Y104016E01


      Step
      System Operation
      (9)
      After receiving the key certification OK signal, the power management control ECU turns on the ACC relay, and then turns on the IG1 and IG2 relays.
      (10)
      The certification ECU (smart key ECU assembly) checks that the power source has turned from off to on (IG), and transmits a steering unlock signal to the power management control ECU and ID code box (immobiliser code ECU).
      (11)
      The power management control ECU receives the steering unlock signal and supplies power to the steering lock ECU.
      (12)
      The steering lock ECU receives the steering unlock signal via the ID code box (immobiliser code ECU), and releases the steering lock.
      (13)
      After checking the steering unlock condition, the certification ECU (smart key ECU assembly) transmits an engine immobiliser disengage signal to the ID code box (immobiliser code ECU).
      (14)
      The ID code box (immobiliser code ECU) certifies the disengage signal of the certification ECU (smart key ECU assembly), transmits the engine immobiliser disengage signal to the ECM, and disengages the engine immobiliser.

      Y104256E01


      Step
      System Operation
      (15)
      After checking that the steering is in the unlocked condition, the power management control ECU turns off the ACC relay and outputs a starter relay signal, and actuates the starter.
      (16)
      When the power management control ECU judges from the engine speed that engine start is completed, it stops the starter relay signal, and stops the starter, and then turns on the ACC relay.
      (17)
      The power management control ECU checks that the engine has started and turns off the indicator light of the engine switch.

      Y104257E01



    3. Pattern B: Off → On (ACC) → On (IG) → Off

      OFF → On (ACC) 
      Step
      System Operation
      (1)
      The driver, carrying the key, enters the vehicle.
      (2)
      When the engine switch is pushed once with the following conditions satisfied, the power management control ECU recognizes the engine switch signal and transmits the key certification request to the certification ECU (smart key ECU assembly)
      1. The shift lever is in P.
      2. The brake pedal is not depressed.
      3. The power source is off.
      (3)
      The rest of the system operation is the same as (3) to (6) in pattern A.
      (4)
      The power management control ECU turns on the ACC relay and will turn on the amber indicator light of the engine switch.
      (5)
      The rest of the system operation is the same as (10) to (14) in pattern A.

      On (ACC) → On (IG) 
      Step
      System Operation
      (1)
      When the power source is on (ACC) and the driver pushes the engine switch again, the power management control ECU recognizes the engine switch signal and turns on the IG1 and IG2 relays.

      On (IG) → Off 
      Step
      System Operation
      (1)
      When the engine switch is pushed once with the following conditions satisfied, the power management control ECU recognizes the engine switch signal and turns off the ACC, IG1 and IG2 relays.
      1. The shift lever is in P.
      2. The brake pedal is not depressed.
      3. The vehicle speed is 0 km/h (0 mph).
      4. The power source is on (IG)
      (2)
      When the power source is changed from on (IG) to off, the power management control ECU will turn off the indicator light of the engine switch.
      (3)
      When the certification ECU recognizes that the power source is off, it transmits the engine immobiliser set signal to the ID code box (immobiliser code ECU).
      (4)
      The ID code box (immobiliser code ECU) certifies that the certification ECU (smart key ECU assembly) signal is appropriate, transmits the engine immobiliser set signal to the ECM, and sets the engine immobiliser.
      (5)
      If the driver door is opened, the certification ECU receives a signal from the main body ECU (multiplex network body ECU). After that, the certification ECU transmits the steering lock signal to the power management control ECU.
      (6)
      The power management control ECU receives the steering lock signal and supplies power to the steering lock ECU.
      (7)
      The steering lock ECU operates the lock motor until the steering lock is engaged if the ID code box (immobiliser code ECU) certifies that the certification ECU (smart key ECU assembly) is appropriate.


      Y104254E01



    4. Pattern C: Off → On (ACC) → On (IG) → On (ACC)

      Step
      System Operation
      (1)
      The system operations for pattern C (off → on (ACC) → on (IG)) are the same as those in pattern B.
      (2)
      When the engine switch is pushed once with the following conditions satisfied, the power management control ECU recognizes the engine switch signal and turns off the IG1 and IG2 relays.
      1. The shift lever is in any position except P.
      2. The brake pedal is not depressed.
      3. The vehicle speed is 0 km/h (0 mph).
      4. The power source is on (IG).
      (3)
      Even after the engine switch turned from on (IG) to on (ACC), the indicator light of the engine switch will remain illuminated in amber.


      Y104849E01

    5. Pattern D: On (IG) → Off

      Step
      System Operation
      (1)
      When the engine switch is pushed once with the following conditions satisfied, the power management control ECU recognizes the engine switch signal and turns off the ACC, IG1 and IG2 relays.
      1. The shift lever is in P.
      2. The vehicle speed is 0 mph (0 km/h).
      3. The power source is on (IG).
      (2)
      The rest of the system operation is same as (3) to (7) of the "on (IG) → off" in pattern B.

    6. Pattern E: On (IG) → On (ACC)

      1. This system operation is the same as for pattern C. However, the indicator light of the engine switch will illuminate as follows:
        1. When the power source is changed from on (IG) to on (ACC), the power management control ECU continues to illuminate the amber indicator light of the engine switch.
        2. When the engine is turned off using the engine switch (power source mode is changed to off), the power management control ECU turns off the indicator light of the engine switch.



    7. When a key battery is weak.

      Step
      System Operation
      (1)
      To operate the smart key system when the key battery is weak, depress the brake pedal and hold the key against the engine switch as shown in the illustration.
      (2)
      The power management control ECU receives the stop light switch signal and transmits a key certification request signal to the certification ECU (smart key ECU assembly).
      (3)
      The certification ECU (smart key ECU assembly) does not receive an ID code response from the door control receiver, so it actuates the transponder key amplifier built into the engine switch.
      (4)
      The transponder key amplifier outputs an engine immobiliser radio wave signal to the key.
      (5)
      The key receives the radio wave signal, and returns a radio wave signal response to the transponder key amplifier.
      (6)
      The transponder key amplifier combines the key ID codes with the radio wave signal response, and transmits it to the certification ECU (smart key ECU assembly).
      (7)
      The certification ECU (smart key ECU assembly) judges and verifies the ID code, and transmits a key certification OK signal to the power management control ECU. The buzzer in the combination meter assembly sounds once.
      (8)
      After the buzzer sounds, if the engine switch is pushed within 10 seconds while the brake pedal is depressed, the engine will be started, the same as with normal smart key operation.
      (9)
      After the buzzer sounds, if the engine switch is pushed within 10 seconds while the brake pedal is not depressed, the power source mode will change to on (ACC) or on (IG), the same as with normal smart key operation.


      Y104255E01



  2. Entry Function

    1. The entry function consists of the following functions:

      Function
      Outline
      Wireless Door Lock Control
      This function is a convenient system for locking and unlocking all the doors and back door at a distance. The operation of this function is the same as that in the wireless door lock control system.
      Entry Illumination
      When a key enters the exterior actuation area of the door electrical key oscillators (LH and RH), the foot lights illuminate.
      Entry Unlock
      When a key is located in the exterior actuation area of any door electrical key oscillator, the door will unlock after the inner part of either front outside door handle is touched.
      1. The driver outside door handle unlocks the driver door. (Driver Door Mode)
      2. The front passenger outside door handle unlocks all doors and the back door. (Driver Door Mode)
      3. Either of the front door outside handle unlocks the all doors and the back door. (All Door Mode)
      Entry Unlock Mode Switching
      Allows switching between 2 modes that can be operated with the entry unlock function.
      1. Driver Door Mode (Default Setting)
      2. All Door Mode
      Entry Lock
      When a key is located in the exterior actuation area of any electrical key oscillator (driver, front passenger or back door) and the engine switch is off, all doors can be locked by simply touching the lock sensor or back door lock switch.
      Entry Back Door Unlock
      When the key is in the actuation area of the outside electrical key oscillator (back door), all the doors can be unlocked by merely pressing the back door opener switch or the back door unlock switch.
      Prevention of Key Confinement
      The key confinement prevention function prevents the vehicle from being locked with a key left inside it. This function operates in 2 different situations: when the lock knob is used (keyless lock) and when an outside door handle lock sensor is used (lock sensor).
      Warning
      When any of the situations below occur, the smart key system causes the certification ECU (smart key ECU assembly) to sound the buzzer in the combination meter and the wireless door lock buzzer, and indicates a warning on the combination meter in order to alert the driver.
      1. An exit warning is activated if the shift lever is in any position except P and the engine switch is in a mode other than off.
      2. An exit warning is activated if the shift lever is in P and the engine switch is in a mode other than off.
      3. A warning is activated if the occupant leaves with the key in inappropriate circumstances.
      4. A warning is activated if the engine switch is operated while the key is outside the actuation area.
      5. A warning is activated if the lock button is operated while the key is inside the vehicle.
      Battery Saving
      If the key remains within the exterior actuation area of any electrical key oscillator (driver, front passenger, or back door), the system maintains periodic communication with the key. Therefore, if the vehicle remains parked in that state for a long time, the key battery and the vehicle battery could be drained.
      Key Cancel
      The following key functions can be cancelled by following certain procedures.
      1. Entry unlock/lock
      2. Back door open
      3. Prevention of key confinement
      4. Warning
      Key Code Registration
      A total of 7 keys can be registered. Key registration enables the registering (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the certification ECU (smart key ECU assembly).

    2. The wireless door lock control system allows the following customizable functions:

      Function
      Outline
      Customizable*
      All Doors Lock
      Pressing the lock button of the key locks doors.
      Default setting is on
      All Doors Unlock (2-step Unlock)
      Pressing the unlock button of the key twice within 3 seconds unlocks all doors after it first unlocks the driver's door.
      Standard
      (Not Customizable)
      Answer Back
      When the doors are being locked or unlocked using the key, the wireless door lock buzzer sounds and the hazard warning lights blink once while locking and twice while unlocking. Also, the answer back function operates when the doors are locked by the automatic relock function.
      Default setting is on
      Panic Alarm
      Keeping the panic button of the key pushed longer than about 0.8 seconds causes the following to activate as an alarm:
      1. The horn and security horn are sounded.
      2. The hazard warning lights, headlights, and taillights are flashed.
      3. The interior lights are illuminated (If the dome switch is in the DOOR position).
      Default setting is on
      Automatic Relock
      If none of the doors are opened within 60 seconds after they are unlocked using the wireless door lock remote control, all the doors will be locked again automatically.
      Default setting is on
      Repeat
      If a door is not locked in response to the locking operation of the key, the main body ECU (multiplex network body ECU) will output a lock signal again after 1 second elapses.
      Standard
      (Not Customizable)
      Door Ajar Warning
      If any door is open or ajar, pushing the lock button of the key will cause the wireless door lock buzzer to sound for about 5 seconds as a warning.
      Default setting is on

      1. *: The customize settings can be turned on/off using the customized body electronics system. For details, refer to the Repair Manual for this model.



    3. Entry Unlock

      Step
      System Operation
      (1)
      When the key enters any exterior actuation area of a front door, the certification ECU (smart key ECU assembly) judges and certifies the key ID code received from the door control receiver.
      (2)
      After the key certification OK is confirmed, the certification ECU (smart key ECU assembly) transmits an unlock stand-by signal to the touch sensor of the relevant door.
      (3)
      At the same time, the certification ECU (smart key ECU assembly) transmits the lighting signals to the foot light on the outside rear view mirror and the interior lights (engine switch illumination and interior lights) to turn them on (Entry Illumination Function).
      (4)
      1. If a touch sensor is touched in this condition, the certification ECU (smart key ECU assembly) transmits a door unlock request signal to the main body ECU (multiplex network body ECU), and unlocks either the driver door or all doors.
        1. The driver outside door handle unlocks the driver door.
        2. The front passenger outside door handle unlocks all doors.
      (5)
      The main body ECU (multiplex network body ECU) sounds the wireless door lock buzzer twice, and flashes the hazard warning lights twice, as an answer back for entry unlock.


      Y104258E01



    4. Entry Unlock Mode Switching

      Step
      System Operation
      (1)
      When the engine switch is off, push the lock button and one of the other buttons on the key at the same time for approximately 5 seconds while the key is in the actuation area.
      (2)
      The certification ECU (smart key ECU assembly) receives this signal from the door control receiver and switches the entry unlock mode.
      (3)
      The main body ECU (multiplex network body ECU) sounds the wireless door lock buzzer to inform the user that the mode has been switched.
      (4)
      If the entry unlock mode needs to be switched again, push the lock button and one of the other three buttons on the key at the same time for approximately 5 seconds after the LED of the key goes off.


      Y104259E01

      HINT:
      This function only switches the entry unlock mode of the smart key system. It is not applied to the unlock function using the wireless door lock control.



    5. Entry Lock

      Step
      System Operation
      (1)
      An entry lock signal is transmitted to the certification ECU (smart key ECU assembly) when the user, while carrying the key, touches the lock sensor or the back door lock switch after exiting the vehicle.
      (2)
      The certification ECU (smart key ECU assembly) transmits a request signal for the indoor electrical key oscillators (front, center, rear) and electrical key oscillators (driver, front passenger, back door) to form actuation areas.
      (3)
      The key receives this signal and returns the ID code to the door control receiver.
      (4)
      The certification ECU (smart key ECU assembly) receives the ID code from the door control receiver, and then judges and certifies the ID code. It then checks the location of the key and, if all the doors are closed, the ECU transmits a door lock signal to the main body ECU (multiplex network body ECU).
      (5)
      The main body ECU (multiplex network body ECU) receives this signal and actuates the lock motors.
      (6)
      The main body ECU (multiplex network body ECU) blinks the hazard warning lights once and sounds the wireless door lock buzzer once as an answerback for the entry lock function.


      Y104260E01



    6. Entry Back Door Unlock

      Step
      System Operation
      (1)
      The unlock signal is transmitted to the certification ECU (smart key ECU assembly) when the driver pushes the back door opener switch while carrying the keys.
      (2)
      The certification ECU (smart key ECU assembly) transmits a request signal for indoor electrical key oscillators (front, center, rear), door electrical key oscillators (LH and RH) and outside electrical key oscillator (back door) to form actuation areas.
      (3)
      The key receives this signal and returns the ID code to the door control receiver.
      (4)
      The certification ECU (smart key ECU assembly) receives the ID code from the door control receiver, and then judges and certifies the ID code, and checks the location of the key. The ECU transmits a back door unlock signal to the main body ECU (multiplex network body ECU).
      (5)
      The ECU that receives this signal actuates the motor to open the back door.


      Y104261E01



    7. Prevention of Key Confinement

      1. The key confinement prevention function prevents the key from being locked inside the vehicle. This function operates in 2 different situations: keyless lock and lock sensor.

      Keyless Lock (Doors locked using lock knobs): 
      Step
      System Operation
      (a)
      When the door is locked by the lock knob in the inside door handle while the key is still in the vehicle, the main body ECU (multiplex network body ECU) receives this signal and transmits the door condition signal to the certification ECU (smart key ECU assembly).
      (b)
      The certification ECU (smart key ECU assembly) transmits a request signal for the indoor electrical key oscillators (front, center, rear), door electrical key oscillators (LH and RH) and outside electrical key oscillator (back door) to form actuation areas.
      (c)
      The key receives this signal and returns the ID code to the door control receiver.
      (d)
      The certification ECU (smart key ECU assembly) receives the ID code from the door control receiver, and then judges and certifies the ID code, and checks the location of the key. The ECU transmits a door unlock signal to the main body ECU (multiplex network body ECU).
      (e)
      The main body ECU (multiplex network body ECU) receives this signal and unlocks all the door lock assemblies.
      (f)
      The main body ECU (multiplex network body ECU) sounds the wireless door lock buzzer.

      Y104263E01


      Lock Sensor (Doors locked using outside handle lock sensor): 
      Step
      System Operation
      (a)
      When the door is locked from the lock sensor while the key is still in the vehicle interior, the certification ECU (smart key ECU assembly) receives this signal and transmits a request signal for the indoor electrical key oscillators (front, center, rear), door electrical key oscillators (LH and RH) and outside electrical key oscillator (back door) to form actuation areas.
      (b)
      The key receives this signal and returns the ID code to the door control receiver.
      (c)
      The certification ECU (smart key ECU assembly) receives the ID code from the door control receiver, and then judges and certifies the ID code, and check the location of the key.
      (d)
      The main body ECU (multiplex network body ECU) sounds the wireless door lock buzzer.

      Y104264E01

  3. Warning

    1. When any of the situations below occur, the smart key system sounds the wireless door lock buzzer, sounds a buzzer in the combination meter assembly and illuminates the engine switch indicator in order to alert the driver.

      Situation
      Condition
      A
      The engine is left running and the shift lever is in a position other than P when the driver gets out of the vehicle.
      B
      The key reminder sounds.
      C
      The engine is left running and the shift lever is in P when the driver gets out of the vehicle.
      D
      A door is ajar.
      E
      The engine is left running when a passenger gets out of the vehicle while holding the key.
      F
      The key is not within the actuation areas.
      G
      The key is left in the vehicle.
      H
      The power management control ECU is malfunctioning.
      I
      The engine cannot be started (system error).
      J
      Immobilizer system certification completion occurs.
      K
      The vehicle is driven without a key.

    2. Situation A

      1. There are 2 patterns for situation A.
        1. Pattern 1:
          When the shift lever is in a position other than P, the engine switch is in a mode other than off, the driver opens the door and attempts to get out of the vehicle.
          In this situation, the following control is performed:

          Possible Effects without Warning
          Sudden vehicle movement, Vehicle theft, Vehicle roll-away
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The engine switch is in a mode other than off.
          2. The shift lever is in any position except P.
          3. The vehicle speed is 0 km/h (0 mph).
          4. The driver door is opened.
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds continuously
          Key Warning Light
          -
          Wireless Door Lock Buzzer
          -
          Engine Switch Illumination
          -
          Warning Stop Condition
          The warning is stopped when one of the following conditions is met:
          1. The engine switch is turned off.
          2. The shift lever is moved to P.
          3. The vehicle speed is above 0 km/h (0 mph).
          4. The driver door is closed.
        2. Pattern 2:
          Under the situation of pattern 1, the driver closes the door and attempts to leave the vehicle while holding the key.
          In this situation, the following control is performed:

          Possible Effects without Warning
          Sudden vehicle start-off, Vehicle theft, Vehicle roll-away
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The shift lever is in any position except P.
          2. The engine switch is in a mode other than off.
          3. The vehicle speed is 0 km/h (0 mph).
          4. The key is not in the vehicle.
          5. The driver door is opened → closed.
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds continuously
          Key Warning Light
          Illuminates
          Wireless Door Lock Buzzer
          Sounds continuously
          Engine Switch Illumination
          -
          Warning Stop Condition
          The warning is stopped when one of the following conditions is met:
          Combination Meter Assembly
          Key Warning Light
          1. The engine switch is turned off.
          2. The key is detected in the vehicle.
          Buzzer
          1. The engine switch is turned off.
          2. The shift lever is moved to P.
          3. The vehicle speed is above 0 km/h (0 mph).
          4. The key is detected in the vehicle.
          Wireless Door Lock Buzzer

    3. Situation B

      1. There are 2 patterns for situation B.
        1. Pattern 1:
          When the driver door is open, the driver turns the engine switch on (ACC) and attempts to leave the vehicle.
        2. Pattern 2:
          When the driver door is open, the driver turns the engine switch from on (IG) to off and attempts to leave the vehicle.
          In these situations, the following control is performed:

      Possible Effects without Warning
      Vehicle theft
      Warning Active Condition
      The warning is activated when one of the following conditions is met:
      1. The engine switch is on (ACC) and the driver door is opened.
      2. The engine switch is off, the steering is unlocked, and the driver door is opened.
      Warning Method
      Combination Meter Assembly
      Buzzer
      Sounds continuously at short and even intervals
      Key Warning Light
      -
      Wireless Door Lock Buzzer
      -
      Engine Switch Illumination
      -
      Warning Stop Condition
      The warning is stopped when one of the following conditions is met:
      1. The engine switch is turned on (IG).
      2. The driver door is closed.
      3. The engine switch is turned off and the steering is locked.

    4. Situation C

      1. There are 2 patterns for situation C.
        1. Pattern 1:
          When the shift lever is in P, the engine switch is in a mode other than off, the driver closes the driver door and attempts to leave the vehicle while holding the key.
          In this situation, the following control is performed:

          Possible Effects without Warning
          Vehicle theft, Engine cannot be restarted, Discharged battery
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The shift lever is in P.
          2. The engine switch is in a mode other than off.
          3. The key is not detected in the vehicle.
          4. The driver door is opened → closed.
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds once
          Key Warning Light
          Illuminates
          Wireless Door Lock Buzzer
          Sounds 3 times
          Engine Switch Illumination
          -
          Warning Stop Condition
          The warning is stopped when either of the following conditions is met:
          1. The engine switch is turned off.
          2. The key is detected in the vehicle (within one of the actuation areas).
        2. Pattern 2:
          Under the situation of pattern 1, the driver touches the lock sensor on the door outside handle.
          In this situation, the following control is performed:

          Possible Effects without Warning
          Vehicle theft, Discharged battery
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The engine switch is in a mode other than off.
          2. The shift lever is in P.
          3. All doors are closed.
          4. The key is not detected in the vehicle interior (within one of the actuation areas).
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds once
          Key Warning Light
          Illuminates for 60 seconds
          Wireless Door Lock Buzzer
          Sounds for 10 seconds
          Engine Switch Illumination
          -
          Warning Stop Condition
          The warning is stopped when one of the following conditions is met:
          Combination Meter Assembly
          Key Warning Light
          1. The engine switch is turned off.
          2. The shift lever is moved to any position except P.
          3. The vehicle speed is above 0 km/h (0 mph).
          Wireless Door Lock Buzzer
          1. Any door is opened.
          2. The engine switch is off.
          3. The shift lever is moved to any position except P.
          4. The vehicle speed is above 0 km/h (0 mph).
          5. The key is detected in the vehicle.

    5. Situation D

      1. The lock sensor on the door outside handle is pushed to perform entry lock, however a door is open.
        In this situation, the following control is performed:

        Possible Effects without Warning
        Vehicle theft
        Warning Active Condition
        The warning is activated when all of the following conditions are met:
        1. The engine switch is off.
        2. Any door is open.
        3. The lock sensor on the outer door handle is on (touched).
        Warning Method
        Combination Meter Assembly
        Buzzer
        -
        Key Warning Light
        -
        Wireless Door Lock Buzzer
        Sounds continuously
        Engine Switch Illumination
        -
        Warning Stop Condition
        The warning is stopped when one of the following conditions is met:
        1. The engine switch is turned to a mode other than off.
        2. All doors are closed.
        3. An unlock operation is performed using the wireless door lock remote function.
        4. The touch sensor on the inside of an outer door handle is used to perform entry unlock.
        5. 5 seconds have elapsed after the wireless door lock buzzer was activated.

    6. Situation E

      1. When the engine is left running, a passenger leaves the vehicle while holding the key.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Engine cannot be restarted
        Warning Active Condition
        The warning is activated when all of the following conditions are met:
        1. The engine switch is in a mode other than off.
        2. A door other than the driver door is opened → closed.
        3. The vehicle speed is 0 km/h (0 mph).
        4. The key is not detected in the vehicle.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Key Warning Light
        Illuminates
        Wireless Door Lock Buzzer
        Sounds 3 times
        Engine Switch Illumination
        -
        Warning Stop Condition
        The warning is stopped when either of the following conditions is met:
        1. The engine switch is turned off.
        2. The key is detected again or returned to the vehicle.

    7. Situation F

      1. When the key is not in the vehicle or the key battery is dead, the driver attempts to start the engine or turn the engine switch on (IG).
        In this situation, the following control is performed:

        Possible Effect without Warning
        User becomes confused
        Warning Active Condition
        The warning is activated when both of the following conditions are met:
        1. The engine switch is pushed.
        2. The key is not in the vehicle (or the key battery is dead).
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Key Warning Light
        Illuminates for 15 seconds
        Wireless Door Lock Buzzer
        -
        Engine Switch Illumination
        -
        Warning Stop Condition
        Check if the key is in the actuation area.
        If the key is in the actuation area, push the wireless door lock switch and confirm that the indicator light on the key comes on. If the indicator does not come on, replace the key battery with a new one.

    8. Situation G

      1. There are 2 patterns for situation G.
        1. Pattern 1:
          The lock sensor on a door outside handle is pushed to perform entry lock with the key left in the vehicle.
          In this situation, the following control is performed:

          Possible Effect without Warning
          Vehicle theft
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The engine switch is off.
          2. All doors are closed.
          3. The key is in the vehicle.
          4. The any door is unlocked.
          5. The lock sensor on the outer door handle is on (touched).
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds once
          Key Warning Light
          -
          Wireless Door Lock Buzzer
          Sounds for 10 seconds
          Engine Switch Illumination
          -
          Warning Stop Condition
          The warning is stopped when one of the following conditions is met:
          1. Any door is opened.
          2. The engine switch is turned to a mode other than off.
          3. The shift lever is moved to any position except P.
          4. The vehicle speed is above 0 km/h (0 mph).
          5. Lock operation is detected.
        2. Pattern 2:
          The door is locked by the lock knob in the inside door handle with the key left in the vehicle.
          In this situation, the following control is performed:

          Possible Effect without Warning
          Vehicle theft
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The door is locked by the lock knob in the inside door handle.
          2. The key is in the vehicle.
          Warning Method
          Combination Meter Assembly
          Buzzer
          -
          Key Warning Light
          -
          Wireless Door Lock Buzzer
          Sounds for 10 seconds
          Engine Switch Illumination
          -
          Warning Stop Condition
          The key is removed from the vehicle interior and the lock sensor is on.

    9. Situation H

      1. A malfunction of the power management control ECU is detected.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Power may be lost
        Warning Active Condition
        A malfunction of the power management control ECU is detected.
        Warning Method
        Combination Meter Assembly
        Buzzer
        -
        Key Warning Light
        -
        Wireless Door Lock Buzzer
        -
        Engine Switch Illumination
        The amber indicator blinks at 2 second intervals (goes off automatically after 15 seconds).
        Warning Stop Condition
        The power management control ECU returns to normal or is repaired.

    10. Situation I

      1. There are 2 patterns for situation I.
        1. Pattern 1:
          When the engine switch is pushed, the key cannot be detected in the vehicle interior two times in a row.
          In this situation, the following control is performed:

          Possible Effect without Warning
          Usability function (user cannot start vehicle)
          Warning Active Condition
          The warning is activated when all of the following conditions are met:
          1. The immobilizer system is set.
          2. The key is not detected in the vehicle.
          3. When the engine switch is turned on (ACC) or on (IG) , a certification error occurs two times in a row.
          Warning Method
          Combination Meter Assembly
          Buzzer
          Sounds once
          Key Warning Light
          Illuminates for 60 seconds
          Wireless Door Lock Buzzer
          -
          Engine Switch Illumination
          -
          Warning Stop Condition
          The warning is stopped when one of the following conditions is met:
          1. The immobilizer system certification result is OK.
          2. The key is detected in the vehicle.
          3. Key certification in the vehicle has stopped either because 30 seconds have passed after any of the doors is opened and closed, or because the brake pedal is depressed.
      2. Pattern 2:
        The driver attempts to start the engine after unlocking the driver door using the mechanical key.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Usability function (user cannot start vehicle)
        Warning Active Condition
        The warning is activated when all of the following conditions are met:
        1. The driver door is unlocked using the mechanical key.
        2. The immobilizer system is set.
        3. The engine switch is pushed.
        4. The key is not detected in the vehicle.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Key Warning Light
        Illuminates for 60 seconds
        Wireless Door Lock Buzzer
        -
        Engine Switch Illumination
        -
        Warning Stop Condition
        The warning is stopped when either of the following conditions is met:
        1. The immobilizer system certification result is OK.
        2. The key is detected in the vehicle.

    11. Situation J

      1. A warning buzzer sounds in the combination meter assembly when a key with a depleted battery is touched to the engine switch while depressing the brake.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Usability function (user cannot start vehicle)
        Warning Active Condition
        Key certification result is OK*
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Key Warning Light
        -
        Wireless Door Lock Buzzer
        -
        Engine Switch Illumination
        -
        Warning Stop Condition
        The warning is stopped when either of the following conditions is met:
        1. The engine is started.
        2. The key is detected in the vehicle.
        *: This situation occurs following Situation I.

    12. In the situation K

      1. A warning buzzer sounds in the combination meter assembly when the vehicle starts moving without a registered key in the vehicle interior.
        In this situation, the following control is performed:

        Possible Effect without Warning
        Engine cannot be restarted
        Warning Active Condition
        When vehicle speed is detected for the first time after the key is removed from the vehicle, the warning is activated.
        Warning Method
        Combination Meter Assembly
        Buzzer
        Sounds once
        Key Warning Light
        Illuminates
        Wireless Door Lock Buzzer
        -
        Engine Switch Illumination
        -
        Warning Stop Condition
        The warning is stopped when either of the following conditions is met:
        1. The engine switch is turned off.
        2. The key is detected in the vehicle.

  4. Battery Saving
    Battery saving preserves the vehicle and key batteries. It is activated when the vehicle remains parked for a long time and when the key is left inside the exterior actuation area.

    When the vehicle remains parked for a long time.
    1. No response from key for more than 5 days
      1. Door electrical key oscillator and outside electrical key oscillator stop emitting signals for creating the actuation area.
    1. These controls are stopped when one of the following conditions is met:
      1. The doors are locked or unlocked using wireless remote control.
      2. The doors are locked or unlocked by touching the lock/unlock sensor on the driver door.
      3. The doors are locked by pressing the back door lock switch.
      4. The back door is opened by pressing the back door unlock switch.
      5. A door is locked or unlocked using the mechanical key.
      6. Door is opened → closed.
    1. No response from key for more than 14 days
      1. Door electrical key oscillator and outside electrical key oscillator stop emitting signals for creating the actuation area.
      2. Door lock sensor and unlock sensor are disabled.
    When the key is left within the exterior detection area.
    1. This state continues longer than 10 minutes
      1. Electrical key oscillator that is detecting the key stops emitting signals for creating the actuation area.
    1. The control is stopped when one of the following conditions is met:
      1. The doors are locked or unlocked using wireless remote control.
      2. The doors are locked or unlocked by touching the lock/unlock sensor on the front door.
      3. The doors are locked by pressing the back door lock switch.
      4. The back door is opened by pressing the back door unlock switch.
      5. A door is locked or unlocked using the mechanical key.

  5. Key Cancel

    1. It is possible to deactivate the following smart key system functions.

      1. Entry Lock
      2. Entry Unlock
      3. Entry Back Door Unlock
      4. Prevention of Key Confinement
      5. Warning

    2. Key cancel is operated when certain operations are performed with the vehicle in the following condition:

      1. Engine switch is off.
      2. Driver door is closed.
      3. Driver door is unlocked.

    3. The operation procedure is as follows:

      1. Unlock once with the unlock button of the key.
      2. Open the driver door within 5 seconds.
      3. Unlock twice with the unlock button of the key within 5 seconds.
      4. Repeat open → close twice for the driver door within 30 seconds, and open again (Driver Door: Open → Close → Open → Close → Open).
      5. Unlock twice with the unlock button of the key within 30 seconds.
      6. Repeat open → close once for the driver door within 30 seconds, and open again (Driver Door: Open → Close → Open).
      7. Close the driver door within 5 seconds.
        When key cancel is activated, the wireless door lock buzzer sounds once. To return to the original condition, perform the procedures again. When key cancel is returned, the wireless door lock buzzer sounds twice.

  6. Key Code Registration Function
    The table below shows the 4 special ID code registration function modes through which up to four different codes can be registered. The codes are electronically registered (written to and stored) in the EEPROM. For details of the recognition code registration procedure, refer to the Repair Manual for this model.

    Mode
    Function
    Rewrite
    Clears all previously registered codes and registers only the newly received codes. This mode is used whenever a transmitter or the ID code box is replaced.
    Add
    Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter. If the number of codes exceeds 7, the oldest registered code is cleared first.
    Confirm
    Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist.
    Prohibit
    To clear all the registered codes and to prohibit the wireless door lock function. This mode is used when a key is lost.


CONSTRUCTION


  1. Key

    1. The key consists of a mechanical key, transmitter for the wireless door lock control, transceiver for the entry function, and transponder chip for the engine immobiliser function.

    2. This mechanical key operates the driver door lock cylinder and glove box lock cylinder, but cannot be used to start the engine. When the mechanical key is used, the cap of the driver door lock cylinder must be removed.

    3. The transmitter for the wireless door lock control has a lock button, unlock button and panic button.

    4. The transceiver of the key receives the signals from the oscillators and returns the ID code to the door control receiver.



    5. The transponder chip for the engine immobiliser function returns a signal to the engine switch as a response to the radio wave received from the engine switch.


      Y104265E01


      Text in Illustration 
      *1
      Mechanical Key
      *2
      Lock Button
      *3
      Unlock Button
      *4
      Panic Button



  2. Engine Switch

    1. The engine switch consists of a momentary type switch, indicator light (amber and green color LEDs), illumination, antenna coil, and transponder key amplifier.

    2. The driver can determine the present power source* and check whether the engine can start or not in accordance with the illumination state of the indicator light.
      *: In this chapter, the expression "power source" has been used in some locations to allow precise explanations. The power source condition is also expressed using conventional expressions such as "engine switch off", "engine switch on (ACC)" and "engine switch on (IG)".



    3. When the power management control ECU detects an abnormality with the smart key system, it makes the amber indicator light flash. If the engine is stopped in this state, it might not be possible to restart it.


      Y100790E02


      Power Source Condition
      Indicator Light Condition
      Brake pedal not depressed
      Brake pedal depressed with shift lever in P or N
      Off
      OFF
      ON (Green)
      On (ACC), On (IG)
      ON (Amber)
      ON (Green)
      Engine Running
      OFF
      OFF
      Steering Lock not Unlocked
      Flashes (Green) for 30 seconds
      Flashes (Green) for 30 seconds
      Smart Key System Malfunction
      Flashes (Amber) for 15 seconds
      Flashes (Amber) for 15 seconds



  3. Power Management Control ECU

    1. Power management control ECU consists of the IG1 relay and IG2 relay actuation circuits, CPU, and hold circuit.



    2. The hold circuit is installed to prevent the power supply to the relays from being cut off when an abnormality occurs in IG1 relay and/or IG2 relay actuation circuits while driving.


      Y100188E01

      HINT:
      The power management control ECU constantly stores the present power source state in its memory. Therefore, if the power to power management control ECU is interrupted due to the removal of the battery, the power management control ECU restores the power source after the battery is reconnected.
      For this reason, if the battery is removed when the power source is in a mode other than off, the power will be restored to the vehicle at the same time the power is restored to power management control ECU (by reconnecting the battery).
      Therefore, before removing the battery, be sure to turn the power source off.


DIAGNOSIS
  1. Start Function

    1. The power management control ECU and certification ECU (smart key ECU assembly) can detect malfunctions in the smart key system when the power source is on (IG).

    2. When the ECUs detect a malfunction, the amber indicator light of the engine switch flashes to warn the driver. At the same time, the ECUs store a 5-digit Diagnostic Trouble Code (DTC) in their memories.

    3. The indicator light warning continues for 15 seconds even after the engine switch is turned to off.

    4. The 5-digit DTCs can be read after connecting the Techstream to the DLC3.

    5. The smart key system may not operate successfully if a malfunction occurs.