TIRE PRESSURE WARNING SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS

Component
Function
Tire Pressure Warning ECU
  1. Receives the data from the tire pressure warning antenna and receiver and monitors the tire pressure.
  2. When the tire pressure warning ECU detects a drop in tire pressure, a system malfunction or initialization function, it outputs the respective signal to the combination meter assembly.
  3. When the tire pressure warning ECU detects a problem with the vehicle speed signal, it uses the engine speed as backup information. If the engine speed is higher than a specified value, the ECU determines that the vehicle is being driven.
Tire Pressure Warning Valve and Transmitter
Detects the inflation pressure and internal temperature of the tire and transmits the measured value and the ID code to the tire pressure warning antenna and receiver.
Tire Pressure Warning Antenna and Receiver
Receives the tire pressure warning valve and transmitter signal and transmits this data to the tire pressure warning ECU.
Combination Meter Assembly
Transmits the vehicle speed signal to the tire pressure warning ECU.
Tire Pressure Warning Light
Illuminates or stays on after blinking for 1 minute to warn the driver in accordance with the signal from the tire pressure warning ECU.
ECM
Transmits the engine speed signal to the tire pressure warning ECU as backup for the vehicle speed signal.

FUNCTION
  1. Warning Function

    1. The tire pressure warning ECU has 2 warning methods that are used, depending on the condition detected.

      Tire Pressure Warning Light
      Detection Condition
      Illuminates*1
      The tire pressure warning ECU has detected that a tire pressure becomes lower than the threshold.
      Stays on after blinking for 1 minute*2
      The tire pressure warning ECU has detected a malfunction in the system.

      1. *1: If the tire pressure warning light illuminates, adjust the tire inflation pressure.
      2. *2: If the tire pressure warning light stays on after blinking for 1 minute, the system is malfunctioning and must be repaired to turn off the light.

  2. Initial Check Function

    1. After the engine switch is turned on (IG), the tire pressure warning ECU illuminates the tire pressure warning light for 3 seconds to check the warning light circuit.


CONSTRUCTION


  1. Tire Pressure Warning Valve and Transmitter

    1. The tire pressure warning valve and transmitters are integrated in the tire valves. Each tire pressure warning valve and transmitter consists of a lithium battery, sensor and transmitter.

    2. The tire pressure warning valve and transmitter directly measures tire inflation pressure and temperature.

    3. The transmitter transmits these measured values to the tire pressure warning antenna and receiver on a frequency of 314.98 MHz.



    4. The ID code is written on the tire pressure warning valve and transmitter.


      X103008E01

      HINT:
      1. The lithium batteries of the tire pressure warning valve and transmitter are a non-replaceable type. If the lithium battery is depleted, the tire pressure warning valve and transmitter must be replaced.
      2. A new tire pressure warning valve and transmitter is shipped in sleep mode to prevent the battery from depleting in storage. When the pressure in the detection portion of the tire pressure warning valve and transmitter increases or decreases by 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds, the tire pressure warning valve and transmitter automatically cancels sleep mode. Once sleep mode is canceled, the tire pressure warning valve and transmitter cannot return to sleep mode.
      3. After a tire pressure warning valve and transmitter is replaced, the ID of the tire pressure warning valve and transmitter must be registered in the tire pressure warning ECU. To register an ID, use the Techstream to enter the ID code that is indicated on the tire pressure warning valve and transmitter.
      4. When replacing a tire pressure warning valve and transmitter, each ID codes of tire pressure warning valve and transmitters must be registered. Even if only 1 tire pressure warning valve and transmitter is replaced, the ID codes of all the tire pressure warning valve and transmitters must be registered again. Record all existing ID codes before beginning the process to enter new ID codes.
      5. For details, refer to the 2010 4RUNNER Repair Manual (Pub. No. RM1430U).


DIAGNOSIS
  1. To inform the driver when the tire pressure warning ECU detects a malfunction in the system, the tire pressure warning ECU will blink the tire pressure warning light for 1 minute, after which the light will stay on. It will also store Diagnostic Trouble Codes (DTCs) in memory.

  2. 5-digit DTCs can be read by connecting the Techstream to the DLC3. For details, refer to the 2010 4RUNNER Repair Manual (Pub. No. RM1430U).