FOUR WHEEL DRIVE CONTROL SYSTEM > DETAILS |
| FUNCTION OF MAIN COMPONENTS |
The main components for the full-time 4WD system have the following functions:
| Component | Function | |
| Combination Meter Assembly | Center Differential Lock Indicator Light | Illuminates to inform the driver that the center differential is locked. |
| 4LO Indicator Light | Illuminates to inform the driver that the transfer position is low range. | |
| Multi Buzzer | Sounds to inform the driver of failure to switch the transfer position or lock the center differential. | |
| Transfer |
|
|
| Transfer Position Switch | Transmits the transfer position (High or Low) signal and center differential lock condition (Lock or Free) signal to the four wheel drive control ECU. | |
| Four Wheel Drive Control ECU | Receives the switch signals and controls the transfer shift actuator assembly. | |
| ECM | Outputs signals such as the shift position signal, throttle position signal, and crankshaft position signal to the four wheel drive control ECU. | |
| CONSTRUCTION |
Transfer
The VF4BM transfer is a compact and lightweight full-time transfer. In this transfer, a planetary gear unit is used in the reduction mechanism and a silent chain is used to reduce noise for the front drive.
The VF4BM transfer consists of a transfer input shaft, planetary gear unit, center differential, silent chain, rear output shaft, front output shaft, and transfer shift actuator assembly.
The center differential uses a TORSEN LSD (Limited Slip Differential). As a result, this LSD ensures the proper torque distribution during acceleration and high-speed driving.
When engaging the center differential lock, the transfer shift actuator assembly operates the center differential lock shift fork. When the 4WD control switch is in the H4L or L4L position, the center differential is locked.
A low viscosity oil is used, also improving fuel consumption.

| *1 | Transfer Input Shaft | *2 | Planetary Gear Unit |
| *3 | Center Differential | *4 | Center Differential Lock Shift Fork |
| *5 | Rear Output Shaft | *6 | Front Output Shaft |
| *7 | Silent Chain | *8 | Transfer Shift Actuator Assembly |
Planetary Gear Unit
The planetary gear unit consists of the planetary sun gear, 4 planetary pinion gears, and planetary carrier.
The planetary sun gear is integrated with the transfer input shaft.
4 planetary pinion gears are fitted to the planetary carrier. Each pinion gear shaft is fixed to the planetary carrier. A planetary spline piece is fitted to the rear of the planetary carrier. When the planetary carrier is to be connected to the output shaft, the power is transferred after engaging the splines on the spline piece with the splines on the high and low clutch sleeve. The high and low clutch sleeve is installed rearward of the transfer input shaft on the center differential case that is splined to the output shaft.
The planetary ring gear is fixed to the transfer case and its internal teeth mesh with the planetary pinion gears.

| *1 | Transfer Input Shaft | *2 | Planetary Sun Gear |
| *3 | Planetary Carrier | *4 | Pinion Shaft |
| *5 | Planetary Pinion Gear | *6 | Planetary Ring Gear |
| *7 | Planetary Spline Piece | *8 | Transfer Clutch Hub Spline Piece |
| *9 | High And Low Clutch Sleeve | *10 | Center Differential Case |
Center Differential (TORSEN LSD)
The center differential (TORSEN LSD) is a torque-sensing LSD. The center differential consists of a differential case, coupling, ring gear, 8 pinion gears, sun gear, and planetary carrier.
It generates a limited-differential torque in proportion to the drive torque, and instantly changes the front and rear torque distribution.
The torque distribution during straight line driving is 40/60 (front/rear), this is helpful for an appropriate steering response during the initial stage of a turn. During the acceleration stage of a turn, the torque distribution to the rear wheels increases.

| *1 | Differential Case | *2 | Planetary Carrier |
| *3 | Pinion Gear | *4 | Sun Gear |
| *5 | Ring Gear | *6 | Ring Gear Coupling |
| *7 | Clutch Plate No. 1 | *8 | Clutch Plate No. 2 |
| *9 | Clutch Plate No. 3 | *10 | Clutch Plate No. 4 |
Transfer Shift Actuator Assembly
Transfer shift actuator, which contains center differential lock shift actuator and H - L shift actuator, cannot be disassembled.
The H - L shift motor in the H - L shift actuator operate H - L shift fork shaft.
The center differential lock shift motor in the center differential lock shift actuator operate center differential lock shift fork shaft.
The H - L limit switch is installed in the H - L shift actuator. The center differential limit switch and center differential lock detection switch are installed in the center differential lock shift actuator.

| *1 |
| *2 | H - L Shift Fork Shaft |
| *3 | Center Differential Lock Shift Fork Shaft | - | - |
The H - L limit switch has two contact point switches (HL1, HL2). Different combinations of the two contact point switches allow detection of the H - L shift motor position (High or Low).

The center differential limit switch has two contact point switches (TL2, TL3). Different combinations of the two contact point switches of limit switch and center differential lock detection switch (P1) allow detection of the center differential lock shift motor position (Lock or Free).

| OPERATION |
Planetary Gear Unit Operation
In the H4F/H4L position, the input shaft is directly connected to the output shaft via the splines at the rear of the transfer input shaft which make this connection via the movable high and low clutch sleeve.
The high and low clutch sleeve is constantly meshed with the rear output shaft via the center differential case. Thus, the rotation of the input shaft is transmitted to the high and low clutch sleeve, to the center differential case, then to the rear output shaft.

| *1 | Planetary Sun Gear | *2 | Planetary Pinion Gear |
| *3 | Planetary Ring Gear | *4 | Planetary Carrier |
| *5 | High and Low Clutch Sleeve | *6 | Transfer Input Shaft |
| *7 | Transfer Clutch Hub Spline Piece | *8 | Center Differential Case |
In the L4L position, the external teeth of the high and low clutch sleeve are meshed with the planetary carrier via the spline piece.
Thus, the rotation of the input shaft is transmitted from the planetary sun gear, to the planetary pinion gears, to the planetary pinion gear shafts, to the planetary carrier, to the planetary spline piece, to the center differential case, through the high and low clutch hub, to the rear output shaft.

| *1 | Planetary Sun Gear | *2 | Planetary Pinion Gear |
| *3 | Planetary Ring Gear | *4 | Planetary Carrier |
| *5 | Planetary Spline Piece | *6 | High and Low Clutch Sleeve |
| *7 | Transfer Input Shaft | *8 | Center Differential Case |
Center Differential Operation
During normal driving (front wheel speed is the same as rear wheel speed), the driving force that is input by the differential case is transmitted (Front: 40/ Rear: 60) as shown below, without involving the LSD function.

| *1 | Differential Case | *2 | Planetary Carrier |
| *3 | Pinion Gear | *4 | Sun Gear |
| *5 | Ring Gear | - | - |
![]() | Input | ![]() | Front Output Torque |
![]() | Rear Output Torque | - | - |
When the front wheels are tending to spin (front wheel speed is greater than rear wheel speed), and a rotational difference begins to exist between the sun gear and the ring gear, the distribution of the torque that is input by the differential case changes instantly before the torque is transmitted. Operation is as follows:

| *1 | Differential Case | *2 | Planetary Carrier |
| *3 | Pinion Gear | *4 | Sun Gear |
| *5 | Ring Gear | *6 | Clutch Plate No. 1 |
| *7 | Clutch Plate No. 4 | - | - |
![]() | Input | ![]() | Front Output Torque |
![]() | Rear Output Torque | ![]() | Limited Differential Torque |
When the rear wheels are tending to spin (front wheel speed is less than rear wheel speed), and a rotational difference begins to exist between the sun gear and the ring gear, the distribution of the torque that is input by the differential case changes instantly before the torque is transmitted. Operation is as follows:

| *1 | Differential Case | *2 | Planetary Carrier |
| *3 | Pinion Gear | *4 | Sun Gear |
| *5 | Ring Gear | *6 | Clutch Plate No. 1 |
| *7 | Clutch Plate No. 4 | - | - |
![]() | Input | ![]() | Front Output Torque |
![]() | Rear Output Torque | ![]() | Limited Differential Torque |