KINETIC DYNAMIC SUSPENSION SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS

Component
Function
Front and Rear Stabilizer Bars
Restrain roll to ensure driving stability.
Front and Rear Stabilizer Control Cylinders
Absorb the impact from the road surface to ensure ride comfort.
Stabilizer Control with Accumulator Housing Assembly
Accumulator Pressure Sensor
Detects the hydraulic pressure and transmits its signal to the stabilizer control ECU.
Stabilizer Control Solenoid Valve
Opens and closes the piping between each stabilizer control cylinder chamber and the accumulator.
Accumulator
Absorbs the pressure from the front stabilizer with tube cylinder assembly and rear stabilizer control cylinder.
Combination Meter Assembly
KDSS Indicator Light
Illuminates to inform the driver when the stabilizer control ECU has detected a malfunction in the KDSS.
Steering Angle Sensor (Spiral Cable Sub-assembly)
Detects the steering direction and the angle of the steering wheel.
Yaw Rate and Acceleration Sensor
  1. Detects the vehicle's yaw rate.
  2. Detects the vehicle's longitudinal and lateral acceleration and deceleration.
Stabilizer Control ECU
Switches the stabilizer control valve based on the signals from the sensors and ECUs.
Skid Control ECU
Sends the vehicle speed signal to the stabilizer control ECU.

CONSTRUCTION


  1. Stabilizer Control Cylinder

    1. The stabilizer control cylinder consists of the piston, upper chamber and lower chamber. There is no connection between the upper chamber and lower chamber.

    2. The upper chamber of the front stabilizer control cylinder is connected to the upper chamber of the rear stabilizer control cylinder.

    3. The lower chamber of the front stabilizer control cylinder is connected to the lower chamber of the rear stabilizer control cylinder.



    4. A bleeder plug is provided for each chamber. To remove the stabilizer control cylinder, fluid must be drained from the bleeder plug.


      X102058E01


      Text in Illustration (Front Stabilizer Control Cylinder) 
      *1
      Bleeder Plug (for Upper Chamber)
      *2
      Bleeder Plug (for Lower Chamber)
      *3
      Piston
      -
      -

      X102129E01


      Text in Illustration (Rear Stabilizer Control Cylinder) 
      *1
      Bleeder Plug (for Upper Chamber)
      *2
      Bleeder Plug (for Lower Chamber)
      *3
      Piston
      -
      -



  2. Stabilizer Control with Accumulator Housing Assembly



    1. The stabilizer control with accumulator housing assembly consists of 2 accumulators, 1 accumulator pressure sensor and 2 stabilizer control solenoid valves. Also, a service valve and a shutter valve used for filling fluid are located in the stabilizer control with accumulator housing assembly.


      X102130E02


      Text in Illustration 
      *1
      Accumulator
      *2
      Accumulator Pressure Sensor
      *3
      Stabilizer Control Solenoid Valve
      *4
      Shutter Valve
      *5
      Service Valve
      -
      -



    2. The metallic bellows type accumulator is used to enhance the gastight performance. The nitrogen gas filling the accumulator produces the initial pressure inside the system and absorbs the pressure from the stabilizer control cylinder, and the fluid volume also varies in accordance with the temperature, thus contributing to an increase in the riding comfort.


      X102131E01


      Text in Illustration 
      *1
      Metallic Bellows
      -
      -
      V100144
      Fluid Chamber
      V100145
      Gas Chamber (Nitrogen Gas)


OPERATION
  1. In accordance with the vehicle speed signal and the signals received from the steering angle sensor and yaw rate sensor assembly, the stabilizer control ECU controls the 2 stabilizer control solenoid valves in order to switch the hydraulic circuit in the system.

  2. The 2 stabilizer control solenoid valves are controlled with the same timing and in the same direction.



  3. While driving at a low speed, the stabilizer control solenoid valve is off and the oil passage between the chamber and accumulator is open.


    X102415E01


    X103009E01


    X103010E01


FAIL-SAFE
  1. If a malfunction occurs in any of the sensors or actuators, the stabilizer control ECU prohibits the system control.


DIAGNOSIS
  1. If the stabilizer control ECU detects a malfunction in the KDSS it, illuminates the KDSS indicator light in the combination meter assembly to alert the driver of the malfunction.

  2. The stabilizer control ECU will also store a Diagnostic Trouble Code (DTC). The DTC can be accessed through the use of an intelligent tester II. For details, refer to the 2010 4RUNNER Repair Manual (Pub. No. RM1430U).