Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Main Body / Data List.

  5. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Ignition switch ACC signal / ON or OFF
    ON: Ignition switch ACC
    OFF: Ignition switch off
    -
    IG SW
    Ignition switch ON signal / ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch off
    -
    FL Door Courtesy SW
    Front door courtesy light switch LH signal / ON or OFF
    ON: Front door LH closed
    OFF: Front door LH open
    -
    Dimmer SW
    Headlight dimmer switch high signal / ON or OFF
    ON: Headlight dimmer switch in high or high flash
    OFF: Headlight dimmer switch in low
    -
    Passing Light SW
    Headlight dimmer switch high flash signal / ON or OFF
    ON: Headlight dimmer switch in high flash
    OFF: Headlight dimmer switch not in high flash
    -
    Front Fog Light SW
    Front fog light switch signal / ON or OFF
    ON: Front fog light switch on
    OFF: Front fog light switch off
    -
    Auto Light SW*
    Headlight dimmer switch AUTO signal / ON or OFF
    ON: Headlight dimmer switch in AUTO
    OFF: Headlight dimmer switch not in AUTO
    -
    Head Light SW (Head)
    Headlight dimmer switch head signal / ON or OFF
    ON: Headlight dimmer switch in head
    OFF: Headlight dimmer switch not in head
    -
    Head Light SW (Tail)
    Headlight dimmer switch tail signal / ON or OFF
    ON: Headlight dimmer switch in tail or head
    OFF: Headlight dimmer switch not in tail or head
    -
    Illumination Rate Info*
    Illumination rate information / 0 ms. to 99.99 ms.
    Value is output according to ambient light levels
    -

    1. *: w/ Automatic Light Control System


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Main Body / Active Test.

  5. According to the display on the Techstream, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Hazard
    Hazard signal
    ON/OFF
    -
    Daytime Running Light
    Running light relay
    ON/OFF
    -
    Taillight Relay
    Taillight relay
    ON/OFF
    -
    Headlight Relay
    Low beam headlight relay
    ON/OFF
    -
    Head Light Hi
    Running light relay
    ON/OFF
    -
    Front Fog Light Relay
    Front fog light relay
    ON/OFF
    -