Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Key System)

ENGINE IMMOBILISER SYSTEM (w/ Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK ENGINE SWITCH

B146454E20

  1. Disconnect the F71 switch connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F71-8 (AGND) - Body ground
    GR - Body ground
    Ground
    Always
    Below 1 Ω
    F71-5 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the F71 switch connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F71-9 (TXCT) - F71-8 (AGND)
    W - GR
    Key code output signal
    Engine switch off, 30 seconds or more after door opened or closed and brake pedal not depressed
    Below 1 V
    F71-9 (TXCT) - F71-8 (AGND)
    W - GR
    Key code output signal
    Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed
    Pulse generation
    (see waveform 1)
    F71-10 (CODE) - F71-8 (AGND)
    V - GR
    Demodulated signal of key code data
    Engine switch off, 30 seconds or more after door opened or closed and brake pedal not depressed
    Below 1 V
    F71-10 (CODE) - F71-8 (AGND)
    V - GR
    Demodulated signal of key code data
    Engine switch off, key held against engine switch and engine switch pushed*
    Pulse generation
    (see waveform 2)
    F71-11 (SWIL) - F71-5 (GND)
    SB - W-B
    Illumination signal
    Engine switch off, light control rheostat fully turned upward and Light control switch off → tail
    Below 2 V → 9 to 14 V
    F71-14 (VC5) - F71-8 (AGND)
    P - GR
    Power supply
    Engine switch off, 30 seconds or more after door opened or closed and brake pedal not depressed
    Below 1 V
    F71-14 (VC5) - F71-8 (AGND)
    P - GR
    Power supply
    Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed
    Pulse generation
    (see waveform 3)

    HINT:
    *: Remove the key battery before performing this inspection.

    If the result is not as specified, the engine switch may have a malfunction.



  5. Inspect using an oscilloscope.



      B051052E14
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F71-9 (TXCT) - F71-8 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed



    2. B051053E17
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F71-10 (CODE) - F71-8 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, key held against engine switch and engine switch pushed*

      HINT:
      *: Remove the key battery before performing this inspection.



    4. B216007E01
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F71-14 (VC5) - F71-8 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed


CHECK CERTIFICATION ECU

B203498E28

  1. Disconnect the F79 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F79-1 (+B) - F79-15 (E)
    V - W-B
    +B power supply
    Always
    11 to 14 V
    F79-17 (CUTB) - F79-15 (E)
    L - W-B
    +B power supply
    Always
    11 to 14 V
    F79-16 (IG) - F79-15 (E)
    W - W-B
    Ignition power supply
    Engine switch off → on (IG)
    Below 1 V → 11 to 14 V
    F79-15 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the F79 ECU connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F79-2 (IND) - F79-15 (E)
    L - W-B
    Security indicator output
    Engine switch off → on (IG)
    Pulse generation
    → Below 2 V
    F79-11 (SWIL) - F79-36 (AGND)
    SB - GR
    Illumination signal
    Engine switch off, light control rheostat fully turned upward and Light control switch off
    Below 2 V
    F79-11 (SWIL) - F79-36 (AGND)
    SB - GR
    Illumination signal
    Engine switch off, light control rheostat fully turned upward and Light control switch tail
    9 to 14 V
    F79-12 (TXCT) - F79-36 (AGND)
    W - GR
    Engine switch TXCT output
    Engine switch off, 30 seconds or more after door opened or closed and brake pedal not depressed
    Below 1 V
    F79-12 (TXCT) - F79-36 (AGND)
    W - GR
    Engine switch TXCT output
    Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed
    Pulse generation
    (see waveform 1)
    F79-13 (CODE) - F79-36 (AGND)
    V - GR
    Engine switch CODE input
    Engine switch off, 30 seconds or more after door opened or closed and brake pedal not depressed
    Below 1 V
    F79-13 (CODE) - F79-36 (AGND)
    V - GR
    Engine switch CODE input
    Engine switch off, key held against engine switch and engine switch pushed*
    Pulse generation
    (see waveform 2)
    F79-28 (VC5) - F79-36 (AGND)
    P - GR
    Engine switch power supply
    Engine switch off, 30 seconds or more after door opened or closed and brake pedal not depressed
    Below 1 V
    F79-28 (VC5) - F79-36 (AGND)
    P - GR
    Engine switch power supply
    Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed
    Pulse generation
    (see waveform 3)
    F79-36 (AGND) - Body ground
    GR - Body ground
    Engine switch ground
    Always
    Below 1 Ω

    HINT:
    *: Remove the key battery before performing this inspection.

    If the result is not as specified, the certification ECU may have a malfunction.



  5. Inspect using an oscilloscope.



      B051052E01
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F79-12 (TXCT) - F79-36 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed



    2. B051053E01
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F79-13 (CODE) - F79-36 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, key held against engine switch and engine switch pushed*

      HINT:
      *: Remove the key battery before performing this inspection.



    4. B216007E01
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F79-28 (VC5) - F79-36 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed


CHECK ID CODE BOX

B118534E25

  1. Disconnect the F72 box connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F72-1 (+B) - F72-8 (GND)
    V - W-B
    +B power supply
    Always
    11 to 14 V
    F72-8 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the F72 box connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F72-5 (EFII) - F72-8 (GND)
    SB - W-B
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected
    11 to 14 V → Pulse generation
    (see waveform 1)
    F72-6 (EFIO) - F72-8 (GND)
    W - W-B
    ECM output signal
    Engine switch off → on (IG)
    11 to 14 V → Pulse generation
    (see waveform 2)
    If the result is not as specified, the ID code box may have a malfunction.



  5. Inspect using an oscilloscope.



      B229710E01
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F72-5 (EFII) - F72-8 (GND)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected



    2. B237527E01
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F72-6 (EFIO) - F72-8 (GND)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)


CHECK STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
C104383E12
  1. Disconnect the F68 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F68-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F68-6 (IG2) - F68-1 (GND)
    W - W-B
    IG2 signal input
    Engine switch off → on (IG)
    Below 1 V → 11 to 14 V
    F68-7 (B) - Body ground
    GR - Body ground
    Power source
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK POWER MANAGEMENT CONTROL ECU

C201247E08

  1. Disconnect the F80 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F80-1 (AM22) - Body ground
    B - Body ground
    Battery power
    Always
    11 to 14 V
    F80-2 (AM21) - Body ground
    B - Body ground
    Battery power
    Always
    11 to 14 V
    F80-5 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F80-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK ECM

A225776E02

  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F50-20 (IMO) - Body ground
    SB - Body ground
    Transponder key ECU output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected
    11 to 14 V → Pulse generation
    (see waveform 1)
    F50-14 (IMI) - Body ground
    W - Body ground
    Transponder key ECU input signal
    Engine switch off → on (IG)
    11 to 14 V → Pulse generation
    (see waveform 2)
    If the result is not as specified, the ECM may have a malfunction.



  2. Inspect using an oscilloscope.



      B229710E01
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F50-20 (IMO) - Body ground
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected



    2. B237527E01
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      F50-14 (IMI) - Body ground
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)