Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > TERMINALS OF ECU

for Preparation Click here



CHECK FRONT POWER SEAT SWITCH LH

B219506E47

  1. Disconnect the b18 and b19 connectors from the front power seat switch LH.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    b18-2 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    b18-7 (+B1) - b18-2 (GND1)
    W - W-B
    Power source
    Always
    11 to 14 V
    b19-12 (SYSB) - b18-2 (GND1)
    P - W-B
    System power source
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the b18 and b19 switch connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    b18-3 (SLD+) - b18-2 (GND1)
    L - W-B
    Sliding motor signal (forward)
    Slide switch off
    Below 1 V
    Slide switch on (Forward)
    11 to 14 V
    b18-4 (SLD-) - b18-2 (GND1)
    GR - W-B
    Sliding motor signal (rearward)
    Slide switch off
    Below 1 V
    Slide switch on (Rearward)
    11 to 14 V
    b18-5 (FRV-) - b18-2 (GND1)
    R - W-B
    Front vertical motor signal (downward)
    Front vertical switch off
    Below 1 V
    Front vertical switch on (Downward)
    11 to 14 V
    b18-6 (+B2) - b18-1 (GND2)
    SB - W-B
    Power source
    Always
    11 to 14 V
    b18-8 (FRV+) - b18-2 (GND1)
    B - W-B
    Front vertical motor signal (upward)
    Front vertical switch off
    Below 1 V
    Front vertical switch on (Upward)
    11 to 14 V
    b18-9 (RCL+) - b18-2 (GND1)
    P - W-B
    Reclining motor signal (forward)
    Reclining switch off
    Below 1 V
    Reclining switch on (Forward)
    11 to 14 V
    b18-11 (RCL-) - b18-2 (GND1)
    LG - W-B
    Reclining motor signal (rearward)
    Reclining switch off
    Below 1 V
    Reclining switch on (Rearward)
    11 to 14 V
    b18-10 (LFT+) - b18-2 (GND1)
    V - W-B
    Lifter motor signal (upward)
    Lifter switch off
    Below 1 V
    Lifter switch on (Upward)
    11 to 14 V
    b18-12 (LFT-) - b18-2 (GND1)
    G - W-B
    Lifter motor signal (downward)
    Lifter switch off
    Below 1 V
    Lifter switch on (Downward)
    11 to 14 V
    b19-1 (SGND) - b18-2 (GND1)
    BR - W-B
    Ground
    Always
    Below 1 Ω
    b19-3 (SSFV) - b19-1 (SGND)
    R - BR
    Front vertical position signal
    Front vertical function operating
    4.5 to 4.8 V
    b19-4 (SSRL) - b19-1 (SGND)
    P - BR
    Lifter position signal
    Lifter function operating
    4.5 to 4.8 V
    b19-5 (SSRS) - b19-1 (SGND)
    G- BR
    Slide position signal
    Slide function operating
    4.5 to 4.8 V
    b19-11 (SSRR) - b19-1 (SGND)
    V - BR
    Reclining position signal
    Reclining function operating
    4.5 to 4.8 V
    If the result is not as specified, the front power seat switch LH may have a malfunction.


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B238680E24

  1. Remove the main body ECU (multiplex network body ECU) .

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-30 (BECU) - Body ground
    -
    Power source
    Always
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Power source (IG)
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    F10-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.