Home › Drivetrain · A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > TERMINALS OF ECM

for Preparation Click here



CHECK ECM

A225776E01

HINT:
The standard voltage at each ECM terminal is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
F51-16 (L4) - B38-12 (E1)
R - BR
L4 position signal
  1. Ignition switch ON
  2. Transfer in L4
Below 1 V
  1. Ignition switch ON
  2. Transfer not in L4
11 to 14 V
F51-20 (TFN) - B38-12 (E1)
R - BR
Neutral position signal
  1. Ignition switch ON
  2. Transfer in neutral
Below 1 V
  1. Ignition switch ON
  2. Transfer not in neutral
11 to 14 V
B37-2 (NSW) - B38-12 (E1)
B - BR
PNP switch signal
  1. Ignition switch ON
  2. Shift lever in P or N
Below 1 V
  1. Ignition switch ON
  2. Shift lever not in P or N
11 to 14 V
B36-35 (P) - B38-12 (E1)
L - BR
P shift position switch signal
  1. Ignition switch ON
  2. Shift lever in P
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in P
Below 1 V
B36-28 (R) - B38-12 (E1)
R - BR
R shift position switch signal
  1. Ignition switch ON
  2. Shift lever in R
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in R
Below 1 V
B36-29 (N) - B38-12 (E1)
G - BR
N shift position switch signal
  1. Ignition switch ON
  2. Shift lever in N
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in N
Below 1 V
B36-27 (D) - B38-12 (E1)
B - BR
D shift position switch signal
  1. Ignition switch ON
  2. Shift lever in D
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in D
Below 1 V
F50-24 (S) - B38-12 (E1)
V - BR
S shift position switch signal
  1. Ignition switch ON
  2. Shift lever in S
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in S
Below 1 V
F50-16 (SFTU) - B38-12 (E1)
GR - BR
Up-shift position switch signal
  1. Ignition switch ON
  2. Shift lever in S
11 to 14 V
  1. Ignition switch ON
  2. Shift lever "+" (up-shift)
Below 1 V
F50-22 (SFTD) - B38-12 (E1)
LG - BR
Down-shift position switch signal
  1. Ignition switch ON
  2. Shift lever in S
11 to 14 V
  1. Ignition switch ON
  2. Shift lever "-" (down-shift)
Below 1 V
B37-36 (S1) - B38-12 (E1)
L-R - BR
S1 solenoid signal
Ignition switch ON
11 to 14 V
1st or 2nd gear
11 to 14 V
3rd, 4th or 5th gear
Below 1 V
B36-33 (S2) - B38-12 (E1)
L-W - BR
S2 solenoid signal
Ignition switch ON
Below 1 V
2nd or 3rd gear
11 to 14 V
1st, 4th or 5th gear
Below 1 V
B36-31 (SR) - B38-12 (E1)
G-W - BR
SR solenoid signal
Ignition switch ON
Below 1 V
5th gear
11 to 14 V
1st gear
Below 1 V
B38-33 (SL1+) - B38-32 (SL1-)
V - R-B
SL1 solenoid signal
Engine idling
Pulse generation
(See waveform 1)
B37-31 (SL2+) - B38-34 (SL2-)
LG - P-L
SL2 solenoid signal
Engine idling
Pulse generation
(See waveform 2)
B37-34 (SLT+) - B37-35 (SLT-)
G-Y - L-B
SLT solenoid signal
Engine idling
Pulse generation
(See waveform 3)
B37-33 (SLU+) - B37-32 (SLU-)
G-R - Y-R
SLU solenoid signal
4th gear (lock-up) or 5th gear (lock-up)
Pulse generation
(See waveform 4)
B38-5 (THO1) - B37-8 (ETHW)
B-R - W-R
No. 1 ATF temperature sensor signal
No. 1 ATF temperature 115°C (239°F) or higher
Below 1.5 V
B38-11 (THO2) - B37-8 (ETHW)
L-Y - W-R
No. 2 ATF temperature sensor signal
No. 2 ATF temperature 115°C (239°F) or higher
Below 1.5 V
B38-9 (SP2+) - B38-10 (SP2-)
G - R
Speed sensor SP2 signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 5)
B38-3 (NT+) - B38-4 (NT-)
B - Y
Speed sensor NT signal
Engine idling
(shift lever in P or N)
Pulse generation
(See waveform 6)
F50-32 (CANH) - B38-12 (E1)
V - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 7)
F50-31 (CANL) - B38-12 (E1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 8)


    C140833E02
  1. Using an oscilloscope, check waveform 1.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    B38-33 (SL1+) - B38-32 (SL1-)
    5 V/DIV., 1 msec./DIV.
    Engine idling



  2. C140833E02
  3. Using an oscilloscope, check waveform 2.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    B37-31 (SL2+) - B38-34 (SL2-)
    5 V/DIV., 1 msec./DIV.
    Engine idling



  4. C140833E02
  5. Using an oscilloscope, check waveform 3.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    B37-34 (SLT+) - B37-35 (SLT-)
    5 V/DIV., 1 msec./DIV.
    Engine idling



  6. C140833E02
  7. Using an oscilloscope, check waveform 4.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    B37-33 (SLU+) - B37-32 (SLU-)
    5 V/DIV., 1 msec./DIV.
    4th gear (lock-up) or 5th gear (lock-up)



  8. C161208E01
  9. Using an oscilloscope, check waveform 5.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    B38-9 (SP2+) - B38-10 (SP2-)
    2 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)



  10. C162170E01
  11. Using an oscilloscope, check waveform 6.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    B38-3 (NT+) - B38-4 (NT-)
    1 V/DIV., 2 msec./DIV.
    Engine idling (shift lever in P or N)



  12. C161206E01
  13. Using an oscilloscope, check waveform 7.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    F50-32 (CANH) - B38-12 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON



  14. C161207E01
  15. Using an oscilloscope, check waveform 8.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    F50-31 (CANL) - B38-12 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON