Home › Drivetrain ยท A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in P or N
    2. OFF: Shift lever not in P or N
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Transfer Neutral
    Transfer status/
    ON or OFF
    1. ON: Transfer in neutral
    2. OFF: Transfer not in neutral
    -
    Transfer L4
    Transfer status/
    ON or OFF
    1. ON: Transfer in L4
    2. OFF: Transfer not in L4
    -
    Stop Light Switch
    Stop light switch status/
    ON or OFF
    1. ON: Brake pedal depressed
    2. OFF: Brake pedal released
    -
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
    2. Lock-up OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm.
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
    -
    Overdrive Cut Switch #1
    Status of the overdrive cut switch No.1/
    ON or OFF
    -
    -
    Shift SW Status (P Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in P
    2. OFF: Shift lever not in P
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in R
    2. OFF: Shift lever not in R
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in N
    2. OFF: Shift lever not in N
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Shift lever held in "+" (up-shift)
    2. OFF: Shift lever not held in "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Shift lever held in "-" (down-shift)
    2. OFF: Shift lever not held in "-" (down-shift)
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    1. ON: Shift lever in S, "+" or "-"
    2. OFF: Shift lever not in S, "+" or "-"
    -
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in D, S, "+" or "-"
    2. OFF: Shift lever not in D, S, "+" or "-"
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. With engine cold: Equal to ambient temperature
    If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
    A/T Oil Temperature 2
    No. 2 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. With engine cold: Equal to ambient temperature
    If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted.
    Lock Up
    Lock-up/
    ON or OFF
    1. ON: Lock-up operating
    2. OFF: Lock-up not operating
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th or 5th
    1. 1st, 2nd, 3rd, 4th or 5th: Shift lever in D
    2. 1st, 2nd, 3rd, 4th or 5th: Shift lever in S
    -
    SLT Solenoid Status
    Shift solenoid SLT status/
    ON or OFF
    1. OFF: Accelerator pedal depressed
    2. ON: Accelerator pedal released
    -
    SLU Solenoid Status
    Shift solenoid SLU status/
    ON or OFF
    1. ON: Shift solenoid SLU operating
    2. OFF: Shift solenoid SLU not operating
    -
    Off-road Guidance Status
    Off-road guidance status/
    OFF, Snow, Sand, Climb, Mogul, Rock or Unset
    -
    -


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLU)
    Operate shift solenoid SLU
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped.
    2. Shift lever in P or N.
    Activate the Solenoid (SLT)*
    Operate shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped.
    2. Engine idling.
    Activate the Solenoid (S1)
    Operate shift solenoid S1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped.
    2. Shift lever in P or N.
    Activate the Solenoid (S2)
    Operate shift solenoid S2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped.
    2. Shift lever in P or N.
    Activate the Lock Up
    Control shift solenoid SLU to set automatic transmission to lock-up
    ON or OFF
    Possible to check shift solenoid valve SLU operation.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%.
    2. Vehicle speed: 60 km/h (37 mph) or more.
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of the shift solenoid valves.
    [Vehicle Condition]
    50 km/h (31 mph) or less.
    Activate the Solenoid (SR)
    Operate shift solenoid SR
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped.
    2. Shift lever in P or N.
    Activate the Solenoid (SL1)
    Operate shift solenoid SL1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped.
    2. Shift lever in P or N.
    Activate the Solenoid (SL2)
    Operate shift solenoid SL2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped.
    2. Shift lever in P or N.

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and Hydraulic Test are different.