Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL INJECTOR

FUEL INJECTOR > INSPECTION

for Preparation Click here



1. INSPECT FUEL INJECTOR ASSEMBLY
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    11.6 to 12.4 Ω

    If the result is not as specified, replace the injector assembly.



2. INSPECT INJECTION VOLUME AND LEAKAGE


    A225366E01
  1. Check the injector injection.

    CAUTION:
    1. This test involves high-pressure fuel and electricity.
    2. Take every precaution regarding safe handling of both the fuel and the electrical parts.
    3. Perform this test in a safe area and avoid any sparks or flame.
    4. Do not smoke.


    1. Assemble SST as shown in the illustration.

      SST
      09268-31012   (09268-41091, 09268-41120, 09268-41140, 09268-41310, 09268-41500, 90467-13001, 95333-06030, 95336-08070)
      Text in Illustration 
      *1
      Fuel Pressure Regulator
      *2
      SST (Union)
      *3
      SST (Clip)
      *4
      SST (Fuel Tube Connector)
      *5
      SST (Hose)
      *6
      SST (Adapter)
      *7
      SST (Clamp)
      *8
      SST (Fuel injector)
      *9
      Fuel Pipe
      *10
      SST (T-Joint)

    2. Discharge the fuel system pressure .

    3. Disconnect the fuel inlet hose (fuel tube connector) from the fuel pipe.

    4. Remove the bolt and disconnect the fuel pressure regulator from the fuel delivery pipe.

      NOTICE:
      Do not disconnect the No. 2 fuel pipe from the fuel pressure regulator.



    5. A174989E02
    6. Connect SST to the fuel pipe.
      Text in Illustration 
      *1
      SST (Fuel Tube Connector)
      *2
      Fuel Pipe

      CAUTION:
      Always read the precautions before connecting the fuel tube connector.



    7. A223041E01
    8. Connect SST (hose) to the fuel inlet of the pressure regulator with another SST (union) and the 2 bolts.

      SST
      09268-31012   (09268-41091, 95336-08070)

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

      Text in Illustration 
      *1
      Fuel Pressure Regulator
      *2
      SST (Hose)
      *3
      No. 2 Fuel Pipe Sub-assembly
      *4
      SST (Union)

    9. Connect the fuel return hose to the fuel outlet of the pressure regulator.



    10. A223042E01
    11. Install a new O-ring to the injector.

    12. Connect SST (adapter and hose) to the injector and hold the injector and adapter with SST (clamp).

      SST
      09268-31012   (09268-41140, 09268-41310, 90467-13001, 95336-08070)
      Text in Illustration 
      *1
      SST (Hose)
      *2
      SST (Clip)
      *3
      O-Ring
      *4
      SST (Adapter)
      *5
      Vinyl Tube
      *6
      SST (Clamp)

    13. Put the injector into a graduated cylinder.

      CAUTION:
      Install a suitable vinyl tube to the injector to contain any gasoline spray.

    14. Connect the Techstream to the DLC3.

    15. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    16. Turn the Techstream on.

    17. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control.



    18. A223043E01
    19. Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

      SST
      09842-30080  

      Standard injection volume:
      71 to 86 cm3 (4.3 to 5.2 cu. in.) per 15 seconds

      Difference between each injector:
      15 cm3 (0.9 cu. in.) or less

      Text in Illustration 
      *a
      Connect
      *1
      SST (Wire)

      NOTICE:
      Always turn the voltage on and off on the battery side, not the fuel pump side.

      If the result is not as specified, replace the injector assembly.

  1. Check for fuel leakage.

    1. In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leakage from the injector.

      Standard fuel leakage:
      1 drop or less per 12 minutes

      If the fuel leakage is not as specified, replace the injector assembly.