Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

DTC    B2271    Ignition Hold Monitor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when a problem, such as an open in the AM2 fuse, an open or short in the wire harness between the fuse and power management control ECU, a short in the IG output circuit inside the power management control ECU, a short between the power management control ECU and relay, or a short in the relay, is detected.

HINT:
When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.


DTC Code
DTC Detection Condition
Trouble Area
B2271
The hold circuit, IG1 relay actuation circuit or IG2 relay actuation circuit inside the power management control ECU is open or shorted.
  1. AM2 fuse
  2. Main body ECU (Driver side junction block assembly) (IG1 relays)
  3. No. 1 integration relay (IG2 relay)
  4. Power management control ECU
  5. Harness or connector

WIRING DIAGRAM


C217202E03


INSPECTION PROCEDURE

NOTICE:
  1. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)


    A207890E08
  1. Disconnect the F80 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F80-2 (AM21) - Body ground
    Always
    9.5 to 14 V
    F80-1 (AM22) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect the F80 power management control ECU connector.



    A207890E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-6 (GND) - Body ground
    Always
    Below 1 Ω
    F80-5 (GND2) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)


    A172755E13
  1. Remove the No. 1 integration relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - 1C-3
    20°C (68°F)
    255 to 387 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (No. 1 Integration Relay)



NG
REPLACE NO. 1 INTEGRATION RELAY
OK


4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2 AND IG1 NO. 3 RELAYS)


    B231373E07
  1. Remove the driver side junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2C-52 - 2B-4
    20°C (68°F)
    101.25 to 123.75 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Driver Side Junction Block Assembly)



NG
REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
OK


5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the F80 power management control ECU connector.

  1. Disconnect the 2C driver side junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-20 (IG1D) - 2C-52
    Always
    Below 1 Ω
    F80-20 (IG1D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)
  1. Disconnect the 2B driver side junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2B-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
  1. Disconnect the F81 power management control ECU connector.

  1. Disconnect the 1C No. 1 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F81-8 (IG2D) - 1C-1
    Always
    Below 1 Ω
    F81-8 (IG2D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
  1. Disconnect the 1C No. 1 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1C-3 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK POWER MANAGEMENT CONTROL ECU
  1. Install the No. 1 integration relay.

  1. Install the driver side junction block assembly.



  1. Connect the power management control ECU connectors.


    C182533E20


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    -
    -

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Switch Condition
    Specified Condition
    F81-8 (IG2D) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
    F80-20 (IG1D) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)