Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

DTC    B2274    ACC Monitor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when there is a problem in the ACC output circuit, which is from the ACC output terminal of the power management control ECU to the ACC relay.

HINT:
When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.


DTC Code
DTC Detection Condition
Trouble Area
B2274
The ACC relay actuation circuit inside the power management control ECU or other related circuit is malfunctioning.
  1. AM2 fuse
  2. Main body ECU (Driver side junction block assembly) (ACC relay)
  3. Power management control ECU
  4. Harness or connector

WIRING DIAGRAM


C217203E03


INSPECTION PROCEDURE

NOTICE:
  1. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)


    A207890E08
  1. Disconnect the F80 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F80-2 (AM21) - Body ground
    Always
    9.5 to 14 V
    F80-1 (AM22) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect the F80 power management control ECU connector.



    A207890E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-6 (GND) - Body ground
    Always
    Below 1 Ω
    F80-5 (GND2) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)


    B231373E08
  1. Remove the driver side junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2C-48 - 2B-4
    20°C (68°F)
    101.25 to 123.75 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Driver Side Junction Block Assembly)



NG
REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
OK


4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the F80 power management control ECU connector.

  1. Disconnect the 2C driver side junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-19 (ACCD) - 2C-48
    Always
    Below 1 Ω
    F80-19 (ACCD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)
  1. Disconnect the 2B driver side junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2B-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK POWER MANAGEMENT CONTROL ECU


  1. Connect the power management control ECU connector.


    C182533E21


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    -
    -

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Switch Condition
    Specified Condition
    F80-19 (ACCD) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)