AIRBAG SYSTEM > SYSTEM DESCRIPTION |
| GENERAL |
In conjunction with the impact absorbing structure for a front collision, the SRS (Supplemental Restraint System) steering pad, instrument panel passenger airbag, lower No. 1 instrument panel airbag and lower No. 2 instrument panel airbag are designed to supplement seat belts in the event of a front collision in order to help reduce shock to the head, chest and knees of the driver and front passenger. This system is a 3-sensor type airbag system which detects the impact during a front collision using the center airbag sensor and front airbag sensors. It also operates the airbag system and seat belt pretensioners.
This vehicle is equipped with electrical-type deceleration sensors for the front airbags in order to detect details about the extent of a collision during the initial stages of the collision. Therefore, the deployment of the driver airbag and instrument panel passenger airbag is controlled in two stages according to the severity of the impact.
In conjunction with the impact absorbing structure for a side collision, the front seat side airbag and curtain shield airbag are designed to help reduce shock to the driver, front passenger and rear outer passengers in the event of a side collision.
The curtain shield airbag helps reduce shock to the front and rear seat occupants. In conjunction with the curtain shield airbag, side airbag sensors are installed at the bottom of the front doors and rear airbag sensors are installed at the bottom of the rear pillars.
In this system, a front side collision is detected by the side airbag sensor in order to simultaneously deploy the front seat side and curtain shield airbags. A rear side collision is detected by the rear airbag sensor and the center airbag sensor in order to deploy the curtain shield airbag.
The center airbag sensor sends the airbag deployment signal to the ECM through the CAN (Controller Area Network) to operate the fuel pump control.
The center airbag sensor sends the airbag deployment signal to the main body ECU via the discrete line to operate collision door lock release control.
| CONSTRUCTION AND OPERATION |
FRONT AIRBAG SENSOR
The front airbag sensors are installed on the right and left radiator supports respectively.
The front airbag sensor consists of a deceleration sensor.
The deceleration sensor is built into the front airbag sensor and the distortion that is created in the sensor is converted into an electric signal based on the vehicle deceleration rate during a front collision. Accordingly, the extent of the initial collision can be detected in detail.
SIDE AIRBAG SENSOR
The side airbag sensors are installed on the bottom of the right and left front doors respectively.
The side airbag sensor consists of a deceleration sensor.
The deceleration sensor is built into the side airbag sensor and the distortion that is created in the sensor is converted into an electric signal based on the vehicle deceleration rate during a front side collision. Accordingly, the extent of the initial collision can be detected in detail.
REAR AIRBAG SENSOR
The rear airbag sensors are installed on the right and left rear pillars respectively.
The rear airbag sensor consists of a deceleration sensor.
The deceleration sensor is built into the rear airbag sensor, and the distortion that is created in the sensor is converted into an electric signal based on the vehicle deceleration rate during a rear side collision. Accordingly, the extent of the initial collision can be detected in detail.
REAR FLOOR SIDE AIRBAG SENSOR
The rear floor side airbag sensor is installed in the center of the floor between the rear pillars.
The rear floor side airbag sensor consists of a deceleration sensor.
The deceleration sensor is built into the rear floor side airbag sensor and the distortion that is created in the sensor is converted into an electric signal based on the vehicle deceleration rate during a side collision. Accordingly, the extent of the initial collision can be detected in detail.
CENTER AIRBAG SENSOR
General
Deceleration sensor and ignition control circuit
Safing sensor
Electronic safing sensor
Backup power source
Diagnostic circuit
Memory circuit
SRS WARNING LIGHT
The SRS warning light is located in the combination meter. It comes on to inform the driver of system trouble when a malfunction is detected in the self-diagnosis of the center airbag sensor. Under normal operating conditions when the ignition switch is turned to ON, it comes on for approximately 6 seconds and then goes off.
| DEPLOYMENT CONDITION |
The center airbag sensor determines whether ignition is necessary based on signals from the deceleration sensor and the front airbag sensor. If the safing sensor turns on simultaneously, current flows to the squibs to deploy the SRS as shown in the illustration below.

The center airbag sensor determines whether ignition is necessary based on signals from the side airbag sensor. If the safing sensor turns on simultaneously, current flows to the squib to deploy the SRS as shown in the illustration below.

The center airbag sensor determines whether ignition is necessary based on signals from the side airbag sensor and rear airbag sensor. If the safing sensor turns on simultaneously, current flows to the squib to deploy the SRS as shown in the illustration below.

The center airbag sensor determines whether ignition is necessary based on signals from the rear airbag sensor. If the safing sensor turns on simultaneously, current flows to the squib to deploy the SRS as shown in the illustration below.
