VEHICLE STABILITY CONTROL SYSTEM > FREEZE FRAME DATA |
| FREEZE FRAME DATA |
Whenever a DTC is stored, the skid control ECU stores the current vehicle (sensor) state as freeze frame data.
The skid control ECU stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS was activated.
| CHECK FREEZE FRAME DATA |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
According to the display on the Techstream, select the trouble code data display with freeze frame data.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Elapsed Time after Freeze Trigger | Elapsed time after freeze trigger/ Min.: 0 msec, Max.: 500 msec | - | - |
| Number of IG ON | Number of times ignition switch turned to ON after storing freeze frame data/ 0 to 31 | - | - |
| Stop Light SW | Stop light switch/ ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| Buzzer | Buzzer/ ON or OFF | ON: Buzzer on OFF: Buzzer off | The combination meter has a built-in buzzer. |
| Parking Brake SW | Parking brake switch/ ON or OFF | ON: Parking brake applied OFF: Parking brake released | - |
| Reservoir Warning SW | Brake fluid level warning switch/ ON or OFF | OFF | - |
| Gear Position | Gear position information/ P,N, R, 1st-8th, Fail or Not R | Actual gear position | - |
| Shift Lever Position | Shift lever position information/ P,N, R, D/M, 1st-6th/B or Fail | Actual shift lever position | - |
| Operated System | Operated system status/ ABS, VSC, TRAC, BA, HAB, PBA, PB, HA-CTRL, Fail, TSC, Sys or Non | - | ABS: ABS is activated. VSC: VSC is activated. TRAC: TRAC is activated. BA: BA is activated. HAB: HAB is activated. PBA: PBA is activated. PB: PB is activated. HA-CTRL: Hill-start assist control is activated. TSC: Trailer sway control is activated. Fail: Fail safe mode is activated. Sys: System prohibit is activated. Non: No operation is activated. |
| Master Cylinder Sensor | Master cylinder pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V | When brake pedal released: 0.3 to 0.9 V | The value increases when the brake pedal is depressed. |
| M/C Sensor Grade | Master cylinder pressure sensor change/ Min.: -30 MPa/s, Max.: 225 MPa/s | When brake pedal released or pedal held at constant position: 0 MPa/s | Changes in proportion with the pedal movement speed when the brake pedal is being operated. |
| Yaw Rate Sensor | Yaw rate and acceleration sensor/ Min.: -128°/s, Max.: 127°/s | Vehicle stopped: 0°/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s | - |
| Lateral G | Lateral G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2
| - | Changes in proportion with the pedal movement speed when the brake pedal is being operated. |
| Forward and Rearward G | Forward and backward G/ Min.: - 25.10 m/s2, Max.: 24.90 m/s2
| - | Changes in proportion with acceleration during acceleration/deceleration. |
| FR Wheel Speed | Front wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| RR Wheel Speed | Rear wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| Vehicle Speed | Maximum wheel speed sensor reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| Vehicle Speed Grade | Vehicle acceleration/ Min.: -25.10 m/s2, Max.: 24.90 m/s2
| Vehicle stopped: 0 m/s2
| Changes in proportion with the vehicle acceleration/deceleration during driving. |
| FR Wheel Direction | Front wheel RH direction signal/ Forward or Back | Forward: Forward Back: Backward | - |
| FL Wheel Direction | Front wheel LH direction signal/ Forward or Back | Forward: Forward Back: Backward | - |
| RR Wheel Direction | Rear wheel RH direction signal/ Forward or Back | Forward: Forward Back: Backward | - |
| RL Wheel Direction | Rear wheel LH direction signal/ Forward or Back | Forward: Forward Back: Backward | - |
| Real Engine Torque | Actual engine torque/ Min.: -1024.0 Nm, Max.: 1023.0 Nm | - | - |
| Accelerator Opening Angle % | Throttle valve opening amount/ Min.: 0.0%, Max.: 128.0% | When accelerator pedal released: 0% | Changes in proportion with the movement of the pedal during accelerator pedal operation. |
| Inspection Mode | Inspection mode/ Other or Inspect | Other: Normal mode Inspect: Inspection mode | - |
| Steering Angle Sensor | Steering angle sensor/ Min.: - 3276.8°, Max.: 3276.7° | Left turn: Increase Right turn: Decrease | - |
| TRAC/VSC Off Mode | TRAC/VSC off mode/ Normal, TRC OFF or VSC OFF | Normal: Normal mode TRC OFF: TRAC off mode VSC OFF: VSC off mode | - |
| CLEAR FREEZE FRAME DATA |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Clear the DTCs and freeze frame data (Click here).