Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

SMART KEY SYSTEM (for Start Function) > TERMINALS OF ECU

for Preparation Click here



CHECK POWER MANAGEMENT CONTROL ECU

C201247E10

  1. Disconnect the F80 power management control ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F80-1 (AM22) - Body ground
    B - Body ground
    +B power supply
    Always
    9.5 to 14 V
    F80-2 (AM21) - Body ground
    B - Body ground
    +B power supply
    Always
    9.5 to 14 V
    F80-5 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F80-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F80-17 (SSW2) - Body ground
    R - Body ground
    Engine switch signal
    Engine switch pushed
    Below 1 Ω
    F80-17 (SSW2) - Body ground
    R - Body ground
    Engine switch signal
    Engine switch not pushed
    10 kΩ or higher
    F80-18 (SSW1) - Body ground
    LG - Body ground
    Engine switch signal
    Engine switch pushed
    Below 1 Ω
    F80-18 (SSW1) - Body ground
    LG - Body ground
    Engine switch signal
    Engine switch not pushed
    10 kΩ or higher
    F80-24 (LIN2) - Body ground
    G - Body ground
    LIN line
    Always
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the F80 power management control ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F80-3 (SLP) - F80-6 (GND)
    SB - W-B
    Steering lock actuator position signal
    Steering lock released
    Pulse generation
    (See waveform 1)
    F80-3 (SLP) - F80-6 (GND)
    SB - W-B
    Steering lock actuator position signal
    Steering lock locked
    Pulse generation
    (See waveform 1)
    F80-8 (SLR+) - F80-6 (GND)
    GR - W-B
    Steering lock motor signal
    Steering lock motor operating
    Below 1 V
    F80-8 (SLR+) - F80-6 (GND)
    GR - W-B
    Steering lock motor signal
    Steering lock motor not operating
    11 to 14 V
    F80-10 (INDW) - F80-6 (GND)
    L - W-B
    Warning signal
    1. Brake pedal depressed
    2. Shift lever in P
    3. Engine switch on (ACC) or on (IG)
    8 to 14 V
    F80-16 (P) - F80-6 (GND)
    V - W-B
    Shift lock signal
    Shift lever in P
    8 to 14 V
    F80-16 (P) - F80-6 (GND)
    V - W-B
    Shift lock signal
    Shift lever not in P
    Below 1 V
    F80-19 (ACCD) - F80-6 (GND)
    R - W-B
    ACC signal
    Engine switch on (ACC)
    8 to 14 V
    F80-19 (ACCD) - F80-6 (GND)
    R - W-B
    ACC signal
    Engine switch off
    Below 1 V
    F80-20 (IG1D) - F80-6 (GND)
    V - W-B
    IG1 signal
    Engine switch on (IG)
    8 to 14 V
    F80-20 (IG1D) - F80-6 (GND)
    V - W-B
    IG1 signal
    Engine switch on (ACC)
    Below 1 V
    F80-22 (INDS) - F80-6 (GND)
    B - W-B
    Vehicle condition signal
    1. Brake pedal depressed
    2. Shift lever in P
    8 to 14 V
    F80-23 (SPD) - F80-6 (GND)
    SB - W-B
    Vehicle speed signal
    Engine switch on (IG), vehicle being driven at approx. 20 km/h (12 mph)
    Pulse generation
    (See waveform 2)
    F81-2 (STA) - F80-6 (GND)
    W - W-B
    Park/neutral position switch signal
    Shift lever in P or N
    Below 1 V
    F81-3 (STAR) - F80-6 (GND)
    B - W-B
    Starter signal
    1. Brake pedal depressed
    2. Shift lever in P
    3. Engine cranking
    8 to 14 V*
    F81-8 (IG2D) - F80-6 (GND)
    L - W-B
    IG2 signal
    Engine switch on (IG)
    8 to 14 V
    F81-8 (IG2D) - F80-6 (GND)
    L - W-B
    IG2 signal
    Engine switch on (ACC)
    Below 1 V
    F81-11 (STP1) - F80-6 (GND)
    V - W-B
    Stop light signal
    Brake pedal depressed
    8 to 14 V
    F81-11 (STP1) - F80-6 (GND)
    V - W-B
    Stop light signal
    Brake pedal released
    Below 1 V

    1. *: Voltage is output for 0.3 seconds when the engine is cranking. Disconnect the connector from the ECM before measuring the voltage.
    If the result is not as specified, the ECU may have a malfunction.



  5. Using an oscilloscope, check the signal waveform of the ECU.



      A130277E04
    1. Waveform 1
      Waveform 1 (Reference) 
      Terminal No. (Symbol)
      F80-3 (SLP) - F80-6 (GND)
      Tool Setting
      2 V/DIV., 100 ms./DIV.
      Vehicle Condition
      Steering lock locked or released



    2. I042329E01
    3. Waveform 2
      Waveform 2 (Reference) 
      Terminal No. (Symbol)
      F80-23 (SPD) - F80-6 (GND)
      Tool Setting
      5 V/DIV., 10 ms./DIV.
      Vehicle Condition
      Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

      HINT:
      As the vehicle speed increases, the wavelength shortens.


CHECK CERTIFICATION ECU

B197893E23

  1. Disconnect the F79 certification ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F79-1 (+B) - Body ground
    V - Body ground
    +B power supply
    Always
    11 to 14 V
    F79-15 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F79-29 (LIN) - Body ground
    G - Body ground
    LIN line
    Always
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK STEERING LOCK ECU
C104383E16
  1. Disconnect the F68 steering lock ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F68-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F68-6 (IG2) - Body ground
    W - Body ground
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    F68-6 (IG2) - Body ground
    W - Body ground
    Ignition power supply
    Engine switch off
    Below 1 V
    F68-7 (B) - Body ground
    GR - Body ground
    +B power supply
    Always
    11 to 14 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the F68 steering lock ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F68-4 (SLP1) - F68-1 (GND)
    SB - W-B
    Steering lock actuator position signal
    Steering lock locked
    11 to 14 V
    F68-4 (SLP1) - F68-1 (GND)
    SB - W-B
    Steering lock actuator position signal
    Steering lock released
    Below 1 V

    1. If the result is not as specified, the ECU may have a malfunction.