Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

SMART KEY SYSTEM (for Start Function) > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.

  5. According to the display on the Techstream, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift P Signal
    Shift P position signal / ON or OFF
    ON: Shift lever in P
    OFF: Shift lever not in P
    -
    Steering Unlock Switch
    Steering lock condition / ON or OFF
    ON: Steering lock released
    (Engine switch on [ACC])
    OFF: Steering lock locked
    (Engine switch off)
    -
    Stop Light Switch1
    Stop light switch 1 / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Start Switch1
    Start switch 1 / ON or OFF
    ON: Engine switch pushed
    OFF: Engine switch not pushed
    -
    Start Switch2
    Start switch 2 / ON or OFF
    ON: Engine switch pushed
    OFF: Engine switch not pushed
    -
    Neutral SW/ Clutch SW
    Status of park/neutral position switch / ON or OFF
    ON: Park/neutral position switch on
    OFF: Park/neutral position switch off
    -
    Latch Circuit
    Latch circuit / ON or OFF
    ON: Engine switch on (IG) or engine running
    OFF: Engine switch off or on (ACC)
    -
    IG1 Relay Monitor(Outside)
    IG1 outer relay monitor / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    IG1 Relay Monitor(Inside)
    IG1 inner relay monitor / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    IG2 Relay Monitor(Outside)
    IG2 outer relay monitor / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    IG2 Relay Monitor(Inside)
    IG2 inner relay monitor / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    Starter Request Signal
    Starter request signal monitor / ON or OFF
    ON: ST relay on
    OFF: ST relay off
    The engine switch is pressed and held with the shift lever in P or N.
    ACC Relay Monitor
    ACC relay monitor / ON or OFF
    ON: Engine switch on (ACC)
    OFF: Engine switch off
    -
    Engine Condition
    Engine condition / Stop or Run
    Stop: Engine stopped
    Run: Engine running
    -
    Vehicle Speed Signal
    Vehicle speed signal / Stop or Run
    Stop: Vehicle stopped
    Run: Vehicle driven (5 km/h (3 mph) or more)
    -
    Shift P Signal Pulse
    Status of shift P signal pulse / Unknown, Error2, Normal2, Error1, Normal3, Error3 or Normal1
    Unknown: Shift P signal pulse unknown
    Error1, Error2 or Error3: Shift P signal pulse abnormal
    Normal1, Normal2 or Normal3: Shift P signal pulse normal
    -
    Power Supply Condition
    Power supply condition / IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    IG2 ON: IG2 relay on
    ST ON: ST request signal on
    All OFF: All relays off
    IG1 ON: IG1 relay on
    ACC ON: ACC relay on
    -
    Powertrain Type
    Status of powertrain type / HV-AT, Cnv-MT, Cnv-AT, Cnv-MMT
    Cnv-AT: Powertrain type automatic transmission
    -
    IG1 Circuit
    Status of IG1 circuit / OK or NG
    OK: IG1 circuit OK
    NG: IG1 circuit NG
    -
    IG2 Circuit
    Status of IG2 circuit / OK or NG
    OK: IG2 circuit OK
    NG: IG2 circuit NG
    -
    Starter SW Sig Mismatch
    Starter switch signal mismatch / Yes or No
    Yes: Starter switch signal mismatch
    No: Starter switch signal match
    -
    Park Signal Mismatch
    Park signal mismatch / Yes or No
    Yes: Park signal mismatch
    No: Park signal match
    -
    Str Lock/Unlock Wait T-Out
    Steering lock/unlock waiting timed out / Yes or No
    Yes: Steering lock/unlock waiting timed out
    No: Steering lock locks/releases normally within specified time
    -
    Key Certifi Wait T-Out
    Key certification waiting timed out / Yes or No
    Yes: Key certification waiting timed out
    No: Key certification completed within specified time
    -
    Number of Diagnosis Code
    Number of diagnostic trouble codes / 0 to 255
    -
    -

    Smart Key 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    #Codes
    Number of diagnostic trouble codes / 0 to 255
    -
    -
    Power Supply Short
    Power supply short / OK or NG(Past)
    OK: Power supply normal
    NG(Past): Power supply short occurred in past
    -
    Power Supply Open
    Power supply open / OK or NG(Past)
    OK: Power supply normal
    NG(Past): Power supply open occurred in past
    -
    Engine Start Request
    Start request signal response / OK or NG
    OK: Received
    NG: Not received
    -
    S Code Check
    S code certification result / OK or NG
    OK: S code certification result normal
    NG: S code certification result abnormal
    -
    L Code Check
    L code certification result / OK or NG
    OK: L code certification result normal
    NG: L code certification result abnormal
    -
    S Code Check(Past)
    S code certification result / OK or NG (Past)
    OK: S code certification result normal
    NG (Past): S code certification result abnormal occurred in past
    -
    L Code Check(Past)
    L code certification result / OK or NG (Past)
    OK: L code certification result normal
    NG (Past): L code certification result abnormal occurred in past
    -


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Power Source Control / Active Test.

  5. According to the display on the Techstream, perform the Active Test.


Power Source Control 
Tester Display
Test Part
Control Range
Diagnostic Note
Indicator Condition
Engine switch indicator
Green / Red / No Sig
Perform this Active Test when the engine switch is off, or while the engine is running.
P Supply for Steering Lock
Power supply for steering lock motor
ON / OFF
This test supplies or stops power to the steering lock motor.