Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

DTC    B2286    Runnable Signal Malfunction

DTC    P0335    Crankshaft Position Sensor Circuit Malfunction (NE Signal)

for Preparation Click here


DESCRIPTION

The power management control ECU and ECM are connected by a cable and the CAN communication lines. These DTCs are stored when the crankshaft position sensor signal information from the cable and the crankshaft position sensor signal information from the CAN communication line are inconsistent.

HINT:
When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.


DTC Code
DTC Detection Condition
Trouble Area
B2286
P0335
The crankshaft position sensor signal information from the cable and the crankshaft position sensor signal information from the CAN communication line are inconsistent.
  1. AM2 fuse
  2. Engine control system
  3. Power management control ECU
  4. Harness or connector

WIRING DIAGRAM


A214075E05


INSPECTION PROCEDURE

NOTICE:
  1. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)


    A207890E08
  1. Disconnect the F80 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F80-2 (AM21) - Body ground
    Always
    9.5 to 14 V
    F80-1 (AM22) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect the F80 power management control ECU connector.



    A207890E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-6 (GND) - Body ground
    Always
    Below 1 Ω
    F80-5 (GND2) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ECM)
  1. Disconnect the F81 power management control ECU connector.

  1. Disconnect the B37 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F81-4 (NE) - B37-29 (NEO)
    Always
    Below 1 Ω
    F81-4 (NE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.READ VALUE USING TECHSTREAM (ENGINE CONDITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the Techstream, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Condition
    Engine condition / Stop or Run
    Stop: Engine stopped
    Run: Engine running
    -

    OK:
    ON (engine stopped) or OFF (engine running) appears on the screen according to the engine condition.



NG
Go to step 5
OK

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLE SHOOTING) (Click here)  

5.CHECK POWER MANAGEMENT CONTROL ECU


  1. Reconnect the power management control ECU connectors.


    C182533E23


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    -
    -

  1. Using an oscilloscope, check the engine speed input signal waveform at the terminal of the power management control ECU.

    Standard Frequency:
    Tester Connection
    Condition
    Specified Condition
    F81-4 (NE) - Body ground
    Engine stopped
    No pulse generated
    Engine running
    Pulse generated
    (1000 rpm: 200 Hz)



NG
GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLE SHOOTING) (Click here)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)