TRANSFER ASSEMBLY > DISASSEMBLY |
| 1. REMOVE TRANSFER INDICATOR SWITCH (4WD POSITION) |
![]() |
Using SST, remove the indicator switch and gasket.
| 2. REMOVE TRANSFER INDICATOR SWITCH (L4 POSITION) |
![]() |
Using SST, remove the indicator switch and gasket.
| 3. REMOVE TRANSFER INDICATOR SWITCH (NEUTRAL POSITION) |
![]() |
Using SST, remove the indicator switch and gasket.
| 4. REMOVE TRANSFER CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY |
Remove the 4 bolts and retainer.
| 5. REMOVE BREATHER OIL DEFLECTOR |
Remove the breather oil deflector.
| 6. REMOVE TRANSFER BEARING RETAINER SUB-ASSEMBLY |
Remove the 5 bolts and bearing retainer.
| 7. REMOVE TRANSFER BEARING RETAINER OIL SEAL |
Using a screwdriver and hammer, tap off the oil seal from the bearing retainer.
| 8. REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY |
Using a chisel and hammer, loosen the staked part of the lock nut.
![]() |
Using SST to hold the companion flange, remove the lock nut.
![]() |
Using SST, remove the companion flange.
| 9. REMOVE FRONT TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL |
Using a screwdriver and hammer, tap out the oil seal from the companion flange.
| 10. REMOVE TRANSFER CASE FRONT OIL SEAL |
![]() |
Using SST, tap out the oil seal.
| 11. REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY |
Using a chisel and hammer, loosen the staked part of the lock nut.
![]() |
Using SST to hold the companion flange, remove the lock nut.
![]() |
Using SST, remove the companion flange.
| 12. REMOVE REAR TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL |
Using a screwdriver and hammer, tap out the oil seal from the companion flange.
| 13. REMOVE TRANSFER CASE REAR OIL SEAL |
![]() |
Using SST, tap out the oil seal.
| 14. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY |
Remove the bolt and speedometer driven hole cover sub-assembly.
Remove the O-ring from the hole cover.
| 15. REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY |
Remove the 5 bolts and extension housing.
| 16. REMOVE TRANSFER OUTPUT SHAFT WASHER |
Remove the 2 output shaft washers.
| 17. REMOVE TRANSFER SPEEDOMETER DRIVE GEAR |
Remove the speedometer drive gear and ball.
| 18. REMOVE REAR TRANSFER CASE |
Remove the 12 bolts and clamp.
Remove the rear transfer case.
| 19. REMOVE FRONT TRANSFER DRIVE SHIFT FORK SHAFT |
Using a hexagon wrench, remove the 2 plugs.
Using a magnet hand, remove the 2 springs and 2 balls from both holes.
Mount the rear transfer case in a vise.
![]() |
Using a 5 mm pin punch and hammer, tap off the 2 slotted pins from the shift shaft stopper and No. 2 transfer gear shift fork.
![]() |
Hold the shift fork shaft in place by hand when removing the pin punch.
Remove the shift fork shaft, No. 1 gear shift fork, spring and shift shaft stopper.
Using a magnet hand, remove the straight pin.
| 20. REMOVE TRANSFER HIGH AND LOW SHIFT FORK SHAFT |
Remove the shift fork shaft and No. 2 gear shift fork.
| 21. REMOVE REAR TRANSFER OUTPUT SHAFT, FRONT TRANSFER DRIVE CHAIN AND TRANSFER DRIVEN SPROCKET |
![]() |
Using a snap ring expander, remove the snap ring.
![]() |
Using a plastic-faced hammer, carefully tap the rear transfer case and remove the output shaft together with the drive chain and driven sprocket.
| *1 | Aluminum Plate |
Remove the output shaft and driven sprocket from the drive chain.
| 22. REMOVE TRANSFER DRIVEN SPROCKET BEARING |
![]() |
Using SST and a press, press out the bearing.
| 23. REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING |
![]() |
Using SST, a press and steel bar, press out the bearing.
| 24. REMOVE FILLER PLUG |
Remove the filler plug and gasket.
| 25. REMOVE DRAIN PLUG |
Remove the drain plug and gasket.
| 26. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY |
![]() |
Remove the 3 bolts and oil separator.
| 27. REMOVE TRANSFER CASE MAGNET |
| 28. REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY |
Remove the 3 bolts and oil pump body.
| 29. REMOVE TRANSFER OIL PUMP BODY O-RING |
![]() |
Using a screwdriver, remove the O-ring from the oil pump body.
| 30. REMOVE TRANSFER OIL PUMP GEAR |
Remove the oil pump gear.
| 31. REMOVE TRANSFER LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT |
![]() |
Using a snap ring expander, remove the snap ring.
Remove the low planetary gear together with the input shaft.
| 32. REMOVE TRANSFER CASE PLUG |
Remove the case plug.
| 33. REMOVE COMPRESSION SPRING |
Remove the spring.
| 34. REMOVE PIN |
Remove the pin.
| 35. REMOVE TRANSFER LOW PLANETARY RING GEAR |
![]() |
Using a screwdriver, pry out the snap ring.
Remove the ring gear from the front transfer case.
| 36. REMOVE TRANSFER CASE OIL SEAL |
Using a screwdriver and hammer, tap out the 2 oil seals.
| 37. REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE |
![]() |
Using a screwdriver, pry out the snap ring.
Remove the spline piece.
| 38. REMOVE FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING |
Remove the needle roller bearing.
| 39. REMOVE TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING |
![]() |
Using a snap ring expander, remove the snap ring.
| 40. REMOVE TRANSFER INPUT GEAR STOPPER |
Remove the input gear stopper.
| 41. REMOVE TRANSFER INPUT GEAR STOPPER BALL |
Remove the ball.
| 42. REMOVE MANUAL TRANSFER PLANETARY CARRIER WASHER |
Remove the washer.
| 43. REMOVE TRANSFER INPUT SHAFT |
Remove the input shaft.
| 44. REMOVE NO. 1 TRANSFER THRUST BEARING RACE |
Remove the bearing race.
| 45. REMOVE TRANSFER LOW PLANETARY GEAR BEARING |
Remove the bearing.
| 46. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING |
Remove the 2 seal rings.
| 47. REMOVE TRANSFER INPUT SHAFT BEARING |
Using a snap ring expander, remove the snap ring.
![]() |
Using SST and a press, press out the bearing.
| 48. REMOVE TRANSFER LOW PLANETARY GEAR BEARING |
![]() |
Using SST, remove the bearing.
| 49. REMOVE TRANSFER CLUTCH HUB |
Using a snap ring expander, remove the snap ring.
Remove the high and low clutch sleeves.
![]() |
Using a press, press out the clutch hub.
| 50. REMOVE REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING |
![]() |
Using SST and a press, press out the bearing.
| 51. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY |
Remove the spacer and ball.
Remove the drive sprocket with front drive clutch sleeve.
Remove the needle roller bearing.
Remove the front drive synchronizer ring.
Remove the front drive sleeve, 3 shifting keys and 2 shifting key springs from the drive sprocket.