TRANSFER ASSEMBLY > REASSEMBLY |
| 1. INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY |
![]() |
| *1 | Shifting Key |
| *2 | Drive Sprocket |
| *3 | Key Spring |
| *4 | Clutch Sleeve |
| *5 | Key Spring Opening |
Apply gear oil to the connecting areas of the clutch sleeve and drive sprocket.
Install the clutch sleeve and 3 shifting keys to the drive sprocket with the 2 shifting key springs.
Apply gear oil to the front drive synchronizer ring taper cone side.
![]() |
Install the front drive synchronizer ring.
| *1 | Front Drive Synchronizer Ring |
| *2 | Drive Sprocket with Front Drive Clutch Sleeve |
| *3 | Needle Roller Bearing |
| *4 | Ball |
| *5 | Spacer |
Apply gear oil to the output shaft and needle roller bearing.
Install the needle roller bearing to the drive sprocket.
Install the drive sprocket (with clutch sleeve).
Install the ball. Then install the spacer so that the spacer is aligned with the ball.
| 2. INSTALL REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING |
Apply gear oil to the connecting areas of the output shaft and bearing.
![]() |
Using SST and a press, press in a new bearing with the outer race snap ring groove facing toward the rear.
| *1 | Groove |
![]() | Rear |
| 3. CHECK TRANSFER DRIVE SPROCKET THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the thrust clearance.
| 4. INSTALL TRANSFER CLUTCH HUB |
Apply gear oil to the connecting areas of the clutch sleeve and clutch hub.
![]() |
Install the clutch sleeve to the clutch hub.
| *1 | Clutch Sleeve |
| *2 | Clutch Hub |
Apply gear oil to the connecting areas of the clutch sleeve and output shaft.
![]() |
Using a press, press in the clutch hub.
| 5. INSTALL TRANSFER OUTPUT SHAFT SNAP RING |
![]() |
Select a new snap ring that allows the minimum axial free play.
| Mark | Specified Condition |
| K | 2.00 to 2.05 mm (0.0787 to 0.0807 in.) |
| L | 2.05 to 2.10 mm (0.0807 to 0.0827 in.) |
| A | 2.10 to 2.15 mm (0.0827 to 0.0846 in.) |
| B | 2.15 to 2.20 mm (0.0846 to 0.0866 in.) |
| C | 2.20 to 2.25 mm (0.0866 to 0.0886 in.) |
| D | 2.25 to 2.30 mm (0.0886 to 0.0906 in.) |
| E | 2.30 to 2.35 mm (0.0906 to 0.0925 in.) |
| F | 2.35 to 2.40 mm (0.0925 to 0.0945 in.) |
| G | 2.40 to 2.45 mm (0.0945 to 0.0965 in.) |
| H | 2.45 to 2.50 mm (0.0965 to 0.0984 in.) |
| J | 2.50 to 2.55 mm (0.0984 to 0.1004 in.) |
Using a snap ring expander, install the snap ring.
| 6. INSTALL TRANSFER LOW PLANETARY GEAR BEARING |
![]() |
Using SST and a press, press in a new bearing.
| 7. INSTALL TRANSFER INPUT SHAFT BEARING |
![]() |
Using SST and a press, press in a new bearing with the groove facing forward.
| 8. INSTALL TRANSFER INPUT BEARING SHAFT SNAP RING |
![]() |
Select a new snap ring that allows 0.1 mm (0.00394 in.) or less of axial free play.
| Mark | Specified Condition |
| 1 | 1.45 to 1.50 mm (0.0571 to 0.0591 in.) |
| 2 | 1.50 to 1.55 mm (o.0591 to 0.0610 in.) |
| 3 | 1.55 to 1.60 mm (0.0610 to 0.0630 in.) |
| 4 | 1.60 to 1.65 mm (0.0630 to 0.0650 in.) |
| 5 | 1.65 to 1.70 mm (0.0650 to 0.0669 in.) |
Using a snap ring expander, install the snap ring.
| 9. INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING |
![]() |
Apply gear oil to 2 new seal rings.
Install the 2 seal rings to the input shaft.
| 10. INSTALL TRANSFER LOW PLANETARY GEAR BEARING |
![]() |
Install the bearing to the low planetary gear.
| *1 | Low Planetary Gear Bearing |
| *2 | No. 1 Thrust Bearing Race |
| *3 | Input Shaft |
![]() | Front |
| 11. INSTALL NO. 1 TRANSFER THRUST BEARING RACE |
Install the bearing race to the low planetary gear.
| 12. INSTALL TRANSFER INPUT SHAFT |
Apply gear oil to the contact surfaces of the input shaft and low planetary gear.
Install the input shaft to the low planetary gear.
| 13. INSTALL MANUAL TRANSFER PLANETARY CARRIER WASHER |
![]() |
| *1 | Planetary Carrier Washer |
| *2 | Input Gear Stopper Ball |
| *3 | Input Gear Stopper |
Apply gear oil to the washer.
Install the washer to the low planetary gear.
| 14. INSTALL TRANSFER INPUT GEAR STOPPER BALL |
Install the ball to the low planetary gear.
| 15. INSTALL TRANSFER INPUT GEAR STOPPER |
Install the stopper to the low planetary gear.
| 16. INSTALL TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING |
![]() |
Select a new snap ring that allows 0.05 to 0.15 mm (0.00196 to 0.00590 in.) of axial free play.
| Mark | Specified Condition |
| A | 2.10 to 2.15 mm (0.0827 to 0.0846 in.) |
| B | 2.15 to 2.20 mm (0.0846 to 0.0866 in.) |
| C | 2.20 to 2.25 mm (0.0866 to 0.0886 in.) |
| D | 2.25 to 2.30 mm (0.0886 to 0.0906 in.) |
| E | 2.30 to 2.35 mm (0.0906 to 0.0925 in.) |
| F | 2.35 to 2.40 mm (0.0925 to 0.0945 in.) |
| G | 2.40 to 2.45 mm (0.0945 to 0.0965 in.) |
| H | 2.45 to 2.50 mm (0.0965 to 0.0984 in.) |
| J | 2.50 to 2.55 mm (0.0984 to 0.1004 in.) |
| K | 2.55 to 2.60 mm (0.1004 to 0.1024 in.) |
| L | 2.60 to 2.65 mm (0.1024 to 0.1043 in.) |
| M | 2.65 to 2.70 mm (0.1043 to 0.1063 in.) |
| N | 2.70 to 2.75 mm (0.1063 to 0.1083 in.) |
| P | 2.75 to 2.80 mm (0.1083 to 0.1102 in.) |
| Q | 2.80 to 2.85 mm (0.1102 to 0.1122 in.) |
| R | 2.85 to 2.90 mm (0.1122 to 0.1142 in.) |
| S | 2.90 to 2.95 mm (0.1142 to 0.1161 in.) |
| T | 2.95 to 3.00 mm (0.1161 to 0.1181 in.) |
| U | 3.00 to 3.05 mm (0.1181 to 0.1201 in.) |
Using a snap ring expander, install the snap ring.
| 17. INSTALL FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING |
![]() |
Apply gear oil to the bearing.
Install the bearing to the low planetary gear.
| 18. INSTALL TRANSFER LOW PLANETARY GEAR SPLINE PIECE |
![]() |
Install the gear spline piece to the low planetary gear.
![]() |
Using a screwdriver, install the snap ring.
| 19. INSTALL TRANSFER CASE OIL SEAL |
![]() |
Using SST and a hammer, tap in 2 new oil seals until their surfaces are flush with the case upper surface.
Coat the lip of the seal with MP grease.
| 20. INSTALL TRANSFER LOW PLANETARY RING GEAR |
![]() |
Install the ring gear to the front transfer case.
![]() | Front |
![]() |
Using a screwdriver, install the snap ring.
| 21. INSTALL PIN |
![]() |
Install the pin.
| *1 | Pin |
| *2 | Compression Spring |
| *3 | Case Plug |
| 22. INSTALL COMPRESSION SPRING |
Install the spring.
| 23. INSTALL TRANSFER CASE PLUG |
Apply adhesive to the threads of the plug.
Install the plug.
| 24. INSTALL TRANSFER LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT |
![]() |
Install the low planetary gear together with the input shaft.
![]() |
Using a snap ring expander, install the snap ring.
| 25. INSTALL TRANSFER OIL PUMP GEAR |
![]() |
Apply gear oil to the sliding surface of the oil pump gear.
Install the oil pump gear.
| 26. INSTALL TRANSFER OIL PUMP BODY O-RING |
![]() |
Coat a new O-ring with gear oil and install it to the pump body.
| 27. INSTALL TRANSFER OIL PUMP BODY SUB-ASSEMBLY |
![]() |
Install the oil pump body with the 3 bolts.
| 28. INSTALL TRANSFER CASE MAGNET |
| 29. INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY |
![]() |
Install the oil separator with the 3 bolts.
| 30. INSTALL FILLER PLUG |
Install a new gasket and the filler plug.
| 31. INSTALL DRAIN PLUG |
Install a new gasket and the drain plug.
| 32. INSTALL TRANSFER INPUT GEAR RADIAL BALL BEARING |
![]() |
Apply gear oil to the contact surfaces of the bearing and driven sprocket.
Using SST and a press, press in a new bearing.
| 33. INSTALL TRANSFER DRIVEN SPROCKET BEARING |
![]() |
Apply gear oil to the contact surfaces of the bearing and driven sprocket.
Using SST and a press, press in a new bearing.
| 34. INSTALL REAR TRANSFER OUTPUT SHAFT, FRONT TRANSFER DRIVE CHAIN AND TRANSFER DRIVEN SPROCKET |
![]() |
Mount the rear transfer case in a vise.
| *1 | Aluminum Plate |
Install the output shaft and driven sprocket to the drive chain.
Install the output shaft, drive chain and driven sprocket to the rear transfer case.
![]() |
Using a snap ring expander, install the snap ring.
| 35. INSTALL TRANSFER HIGH AND LOW SHIFT FORK SHAFT |
![]() |
Apply gear oil to the connecting areas of the shift fork shaft and each part.
Install the shift fork shaft and No. 2 gear shift fork.
| *1 | Shift Fork Shaft |
| *2 | No. 2 Gear Shift Fork |
Install the spring and ball to the hole.
Apply adhesive to the threads of the plug.
Using a hexagon wrench, install the plug.
| 36. INSTALL FRONT TRANSFER DRIVE SHIFT FORK SHAFT |
![]() |
Apply gear oil to the straight pin.
Install the straight pin to the hole.
Apply gear oil to the connecting areas of the shift fork shaft and each part.
![]() |
Install the shift fork shaft, No. 1 gear shift fork, spring and shift shaft stopper.
| *1 | Shift Fork Shaft |
| *2 | Spring |
| *3 | No. 1 Gear Shift Fork |
| *4 | Shift Shaft Stopper |
![]() | Front |
![]() |
Using a pin punch and hammer, install the 2 slotted pins.
![]() |
Install the spring and ball to the hole.
| *1 | Plug |
| *2 | Spring |
| *3 | Ball |
Apply adhesive to the threads of the plug.
Using a hexagon wrench, install the plug.
| 37. INSTALL REAR TRANSFER CASE |
![]() |
Apply seal packing to the rear transfer case as shown in the illustration.
| *1 | Seal Packing |
![]() |
Install the clamp and rear case with the 12 bolts.
| 38. INSTALL TRANSFER SPEEDOMETER DRIVE GEAR |
Install the speedometer drive gear and ball.
| 39. INSTALL TRANSFER OUTPUT SHAFT WASHER |
Install the 2 output washers.
| 40. INSTALL TRANSFER EXTENSION HOUSING SUB-ASSEMBLY |
![]() |
Apply seal packing to the extension housing as shown in the illustration.
| *1 | Seal Packing |
Apply adhesive to the threads of the bolts.
Install the extension housing with the 5 bolts.
| 41. INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY |
Install a new O-ring and the speedometer driven hole cover sub-assembly with the bolt.
| 42. INSTALL TRANSFER CASE FRONT OIL SEAL |
![]() |
Coat the lip of a new oil seal with MP grease.
Using SST and a hammer, tap in the oil seal until its metal ring contacts the case.
| 43. INSTALL FRONT TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL |
![]() |
Using SST and a hammer, tap in a new oil seal.
| 44. INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Apply gear oil to the connecting areas of the companion flange and driven sprocket.
Install the companion flange to the driven sprocket.
Using SST to hold the companion flange, install a new lock nut.
![]() |
Using a chisel and hammer, stake the lock nut to the driven sprocket.
| *a | CORRECT |
| *b | INCORRECT |
| 45. INSTALL TRANSFER CASE REAR OIL SEAL |
![]() |
Coat the lip of a new oil seal with MP grease.
Using SST and a hammer, tap in the oil seal until its surface is flush with the case upper surface.
| 46. INSTALL REAR TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL |
![]() |
Using SST and a hammer, tap in a new oil seal.
| 47. INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Apply gear oil to the connecting areas of the companion flange and output shaft.
Install the companion flange to the output shaft.
Using SST to hold the companion flange, install a new lock nut.
![]() |
Using a chisel and hammer, stake the lock nut.
| *a | CORRECT |
| *b | INCORRECT |
| 48. INSTALL TRANSFER BEARING RETAINER OIL SEAL |
![]() |
Using SST and a hammer, tap in a new oil seal until its surface is flush with the bearing retainer upper surface.
Coat the lip of the oil seal with MP grease.
| 49. INSTALL TRANSFER BEARING RETAINER SUB-ASSEMBLY |
![]() |
Apply seal packing to the bearing retainer as shown in the illustration.
| *1 | Seal Packing |
Apply sealant to the bolt threads.
![]() |
Install the retainer with the 5 bolts.
| 50. INSTALL BREATHER OIL DEFLECTOR |
Install the breather oil deflector.
| 51. INSTALL TRANSFER CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY |
![]() |
Install the retainer with the 4 bolts.
| 52. INSTALL TRANSFER INDICATOR SWITCH (4WD POSITION) |
Using SST, install a new gasket and the indicator switch.
| 53. INSTALL TRANSFER INDICATOR SWITCH (L4 POSITION) |
Using SST, install a new gasket and the indicator switch.
| 54. INSTALL TRANSFER INDICATOR SWITCH (NEUTRAL POSITION) |
Using SST, install a new gasket and the indicator switch.