Home › Drivetrain ยท AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock)

REAR DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock) > REASSEMBLY

for Preparation Click here



1. ASSEMBLE DIFFERENTIAL CASE


C216548
  1. Install the rear differential side gear thrust washer to the rear differential side gear.

  1. Install the rear differential pinion thrust washer and rear differential pinion to the rear differential spider.

  1. Fix the differential case RH in place.



    ZK09096
  1. Install the rear differential side gear and rear differential spider to the differential case RH.



    ZK09097
  1. Using a dial indicator, measure the differential case RH side backlash while pushing the pinion toward the case.

    Standard backlash:
    0.05 to 0.20 mm (0.00197 to 0.00787 in.)

  1. Remove the rear differential spider from the differential case RH.



    ZK09098
  1. Install the rear differential side gear and rear differential spider to the differential case LH.

  1. Using a dial indicator, measure the differential case LH side backlash while pushing the pinion toward the case.

    Standard backlash:
    0.05 to 0.20 mm (0.00197 to 0.00787 in.)

    If the backlash is not within the specification, install 2 side gear thrust washers of a different thickness.

    Standard Thrust Washer:

    Specified Condition
    Specified Condition
    0.87 to 0.93 mm (0.0343 to 0.0366 in.)
    1.17 to 1.23 mm (0.0461 to 0.0484 in.)
    0.97 to 1.03 mm (0.0382 to 0.0406 in.)
    1.27 to 1.33 mm (0.0500 to 0.0524 in.)
    1.07 to 1.13 mm (0.0421 to 0.0445 in.)
    -



    C216546E02
  1. Align the matchmarks and assemble the differential case from the RH and LH cases.
    Text in Illustration 
    *a
    Matchmark

  1. Using a plastic-faced hammer, install the differential case.

  1. Install the 8 bolts.

    Torque:
    47 N*m{ 480 kgf*cm , 35 ft.*lbf }



2. INSTALL DIFFERENTIAL RING GEAR
  1. Clean the contact surfaces of the differential case and ring gear.

  1. Heat the ring gear in water that is approximately 100°C (212°F).

  1. Carefully remove the ring gear from the boiling water.

  1. After the moisture on the ring gear has completely evaporated, quickly install the ring gear to the differential case.



    C216547E02
  1. Align the matchmark on the ring gear with that of the differential case.

  1. After the ring gear cools down sufficiently, apply adhesive to the 12 bolts and install them.

    Adhesive:
    Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent

    Torque:
    97 N*m{ 985 kgf*cm , 71 ft.*lbf }



3. INSTALL REAR DIFFERENTIAL CASE BEARING


C216550E01
  1. Using SST and a press, press the bearing onto the differential case.

    SST
    09308-14010  
    09950-60010   (09951-00490)



4. INSPECT DIFFERENTIAL RING GEAR RUNOUT


C216538
  1. Install the differential case to the carrier and install the 2 adjusting nuts so that there is no play in the bearing.

  1. Install the 2 bearing caps with the 4 bolts.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }

  1. Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.00276 in.)

  1. Remove the 2 bearing caps, 2 adjusting nuts and differential case.



5. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


C197664E01
  1. Using SST and a press, press in the roller bearing (outer) to the carrier.

    SST
    09308-14010  
    09309-14040  



6. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C216552E01
  1. Install the plate washer to the carrier.

    HINT:
    First, install a washer with the same thickness as the removed washer, and then check the tooth contact pattern. Replace the washer with one of a different thickness if necessary.

  1. Using SST and a press, press the roller bearing (outer) into the carrier.

    SST
    09950-70010   (09951-07200)
    09255-10012  



7. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING


SA03102E02
  1. Using SST and a press, press the roller bearing (inner) onto the drive pinion.

    SST
    09309-14040  



8. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD


C028218E01
  1. Install the drive pinion, rear drive pinion tapered roller bearing and rear differential drive pinion oil slinger.

    HINT:
    Install the spacer and oil seal after adjusting the gear contact pattern.



    R011163E03
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil LSD to its threads and tip.



    ZK09978E01
  1. Using a 30 mm socket wrench, adjust the drive pinion preload by tightening the companion flange nut.

  1. Using SST to hold the companion flange in place, tighten the nut.

    SST
    09330-00021  

    Torque:
    457 N*m{ 4660 kgf*cm , 337 ft.*lbf } or less

    NOTICE:
    1. As there is no spacer, tighten the nut a little at a time. Be careful not to overtighten the nut.
    1. Apply hypoid gear oil to the nut.



    C003092
  1. Using a torque wrench, measure the preload.

    Standard Preload (at Starting):
    Item
    Specified Condition
    New bearing
    0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf)
    Used bearing
    0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)

    NOTICE:
    For a more accurate measurement, rotate the bearing forward and backward several times before measuring.



9. INSTALL DIFFERENTIAL CASE ASSEMBLY


C216542
  1. Place the 2 bearing outer races on their respective bearings.

    HINT:
    Do not interchange the right and left races.



10. ADJUST RING GEAR BACKLASH


    C217048
  1. Install the plate washer on the side without the ring gear teeth.

    NOTICE:
    Make sure that the ring gear has backlash.



    C216537
  1. Using a dial indicator, while holding the companion flange, measure the ring gear backlash.

    Standard backlash (reference):
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)



    C217048
  1. Select a plate washer for the side without the ring gear teeth using the backlash as a reference.



    C216549
  1. Select a plate washer for the side with the ring gear teeth so that there is no clearance between the outer race and case.

  1. Using a plastic-faced hammer, install the plate washer for the side with the ring gear teeth.



    C216537
  1. Using a dial indicator, while holding the companion flange, measure the ring gear backlash.

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

    HINT:
    1. There should be no clearance between the plate washer and case.
    2. Make sure that there is ring gear backlash.



11. ADJUST SIDE BEARING PRELOAD


C124163
  1. Remove the ring gear teeth side plate washer and, using a micrometer, measure the thickness.

  1. Using the backlash as a reference, select a new washer that is 0.05 to 0.20 mm (0.00197 to 0.00787 in.) thicker than the removed washer and, using a plastic-faced hammer, tap it in so that it fits against the bearing.

    HINT:
    Select a washer which can be pressed in 2/3 of the full amount with your finger.



    C216537
  1. Recheck the ring gear backlash.

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00788 in.)

    If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

    HINT:
    An approximately 0.02 mm (0.000787 in.) change in each plate washer results in a 0.03 mm (0.00118 in.) change in the backlash.


    Standard Washer:

    Mark
    Specified Condition
    Mark
    Specified Condition
    70
    2.05 to 2.07 mm (0.0808 to 0.0816 in.)
    62
    2.41 to 2.43 mm (0.0950 to 0.0957 in.)
    71
    2.07 to 2.09 mm (0.0816 to 0.0823 in.)
    63
    2.43 to 2.45 mm (0.0957 to 0.0965 in.)
    72
    2.09 to 2.11 mm (0.0823 to 0.0831 in.)
    64
    2.45 to 2.47 mm (0.0965 to 0.0972 in.)
    73
    2.11 to 2.13 mm (0.0831 to 0.0839 in.)
    65
    2.47 to 2.49 mm (0.0972 to 0.0980 in.)
    74
    2.13 to 2.15 mm (0.0839 to 0.0847 in.)
    66
    2.49 to 2.51 mm (0.0980 to 0.0988 in.)
    75
    2.15 to 2.17 mm (0.0847 to 0.0855 in.)
    67
    2.51 to 2.53 mm (0.0988 to 0.0996 in.)
    76
    2.17 to 2.19 mm (0.0855 to 0.0863 in.)
    68
    2.53 to 2.55 mm (0.0996 to 0.1000 in.)
    77
    2.19 to 2.21 mm (0.0863 to 0.0871 in.)
    69
    2.55 to 2.57 mm (0.1000 to 0.1012 in.)
    78
    2.21 to 2.23 mm (0.0871 to 0.0879 in.)
    01
    2.57 to 2.59 mm (0.1012 to 0.1020 in.)
    79
    2.23 to 2.25 mm (0.0879 to 0.0887 in.)
    32
    2.59 to 2.61 mm (0.1020 to 0.1028 in.)
    80
    2.25 to 2.27 mm (0.0887 to 0.0894 in.)
    33
    2.61 to 2.63 mm (0.1028 to 0.1035 in.)
    81
    2.27 to 2.29 mm (0.0894 to 0.0902 in.)
    03
    2.63 to 2.65 mm (0.1035 to 0.1043 in.)
    82
    2.27 to 2.31 mm (0.0902 to 0.0891 in.)
    34
    2.65 to 2.67 mm (0.1043 to 0.1051 in.)
    83
    2.31 to 2.33 mm (0.0891 to 0.0918 in.)
    35
    2.67 to 2.69 mm (0.1051 to 0.1059 in.)
    84
    2.33 to 2.35 mm (0.0918 to 0.0926 in.)
    05
    2.69 to 2.71 mm (0.1059 to 0.1067 in.)
    85
    2.35 to 2.37 mm (0.0926 to 0.0934 in.)
    36
    2.71 to 2.73 mm (0.1067 to 0.1075 in.)
    86
    2.37 to 2.39 mm (0.0934 to 0.0942 in.)
    37
    2.73 to 2.75 mm (0.1075 to 0.1082 in.)
    87
    2.39 to 2.41 mm (0.0942 to 0.0950 in.)
    07
    2.75 to 2.77 mm (0.1082 to 0.1091 in.)



12. INSTALL BEARING CAP


    C216540E02
  1. Align the matchmarks on the cap and carrier.
    Text in Illustration 
    *a
    Matchmark

  1. Install the 2 bearing caps with the 4 bolts.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }

    HINT:
    After rotating the ring gear 5 times or more, recheck the backlash.



13. INSPECT DIFFERENTIAL RING GEAR RUNOUT


    C216538
  1. Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.00276 in.)

    If the runout is more than the maximum, replace the ring gear.



14. INSPECT TOTAL PRELOAD


C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard total preload (at starting):
    Drive pinion preload plus 0.20 to 0.40 N*m (2 to 4 kgf*cm, 2 to 3 in.*lbf)

    If necessary, disassemble and inspect the differential.



15. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION


C217045
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.

  1. Hold the companion flange firmly in place and rotate the ring gear in both directions.



  1. Inspect the tooth contact pattern.


    1. C113184E01


    2. C217047E01
      If the teeth are not engaged properly, use the following chart to select a proper washer.
      Text in Illustration 
      *1
      Plate Washer
      *2
      Rear Drive Pinion Rear Tapered Roller Bearing (Outer)

      Standard Plate Washer:

      Specified Condition
      Specified Condition
      1.845 to 1.855 mm (0.0726 to 0.0730 in.)
      2.085 to 2.095 mm (0.0821 to 0.0825 in.)
      1.855 to 1.865 mm (0.0730 to 0.0734 in.)
      2.095 to 2.105 mm (0.0825 to 0.0829 in.)
      1.865 to 1.875 mm (0.0734 to 0.0738 in. )
      2.105 to 2.115 mm (0.0829 to 0.0833 in.)
      1.875 to 1.885 mm (0.0738 to 0.0742 in.)
      2.115 to 2.125 mm (0.0833 to 0.0837 in.)
      1.885 to 1.895 mm (0.0742 to 0.0746 in.)
      2.125 to 2.135 mm (0.0837 to 0.0841 in.)
      1.895 to 1.905 mm (0.0746 to 0.0750 in.)
      2.135 to 2.145 mm (0.0841 to 0.0844 in.)
      1.905 to 1.915 mm (0.0750 to 0.0754 in.)
      2.145 to 2.155 mm (0.0844 to 0.0848 in.)
      1.915 to 1.925 mm (0.0754 to 0.0758 in.)
      2.155 to 2.165 mm (0.0848 to 0.0852 in.)
      1.925 to 1.935 mm (0.0758 to 0.0762 in.)
      2.165 to 2.175 mm (0.0852 to 0.0856 in.)
      1.935 to 1.945 mm (0.0762 to 0.0766 in.)
      2.175 to 2.185 mm (0.0856 to 0.0860 in.)
      1.945 to 1.955 mm (0.0766 to 0.0770 in.)
      2.185 to 2.195 mm (0.0860 to 0.0864 in.)
      1.955 to 1.965 mm (0.0770 to 0.0774 in.)
      2.195 to 2.205 mm (0.0864 to 0.0868 in.)
      1.965 to 1.975 mm (0.0774 to 0.0778 in.)
      2.205 to 2.215 mm (0.0868 to 0.0872 in.)
      1.975 to 1.985 mm (0.0778 to 0.0781 in.)
      2.215 to 2.225 mm (0.0872 to 0.0876 in.)
      1.985 to 1.995 mm (0.0781 to 0.0785 in.)
      2.225 to 2.235 mm (0.0876 to 0.0880 in.)
      1.995 to 2.005 mm (0.0785 to 0.0789 in.)
      2.235 to 2.245 mm (0.0880 to 0.0884 in.)
      2.005 to 2.015 mm (0.0789 to 0.0793 in.)
      2.245 to 2.255 mm (0.0884 to 0.0888 in.)
      2.015 to 2.025 mm (0.0793 to 0.0797 in.)
      2.255 to 2.265 mm (0.0888 to 0.0892 in.)
      2.025 to 2.035 mm (0.0797 to 0.0801 in.)
      2.265 to 2.275 mm (0.0892 to 0.0896 in.)
      2.035 to 2.045 mm (0.0801 to 0.0805 in.)
      2.275 to 2.285 mm (0.0896 to 0.0900 in.)
      2.045 to 2.055 mm (0.0805 to 0.0809 in.)
      2.285 to 2.295 mm (0.0900 to 0.0904 in.)
      2.055 to 5.065 mm (0.0809 to 0.0813 in.)
      2.295 to 2.305 mm (0.0904 to 0.0907 in.)
      2.065 to 2.075 mm (0.0813 to 0.0817 in.)
      2.305 to 2.315 mm (0.0907 to 0.0911 in.)
      2.075 to 2.085 mm (0.0817 to 0.0821 in.)
      -



16. REMOVE REAR DRIVE PINION NUT


SA02349E03
  1. Using SST to hold the companion flange in place, remove the nut.

    SST
    09330-00021  



17. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


B087869E01
  1. Using SST, remove the rear drive pinion companion flange sub-assembly.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



18. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


19. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)


20. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)


Z000641E01
  1. Using SST, remove the rear drive pinion front tapered roller bearing (inner) from the drive pinion.

    SST
    09556-22010  



21. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


C093601E01
  1. Install a new bearing spacer to the drive pinion.



22. INSTALL DIFFERENTIAL OIL STORAGE RING


    C216551E01
  1. Using SST, tap in a new oil storage ring.



23. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)


24. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)


25. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


26. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL
  1. Apply MP grease to a new oil seal.



    C217046E03
  1. Using SST and a hammer, tap in the oil seal.

    SST
    09554-30011  

    Standard oil seal depth:
    -0.3 to 0.3 mm (-0.0118 to 0.0118 in.)

    Text in Illustration 
    *a
    Oil Seal Depth



27. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


R011163E17
  1. Using SST, install the companion flange to the drive pinion.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



    SA02351E03
  1. Coat the threads of a new nut with hypoid gear oil.

  1. Using SST to hold the flange, tighten the nut.

    SST
    09330-00021  

    Torque:
    457 N*m{ 4660 kgf*cm , 337 ft.*lbf } or less



28. INSPECT DRIVE PINION PRELOAD


SA02352E01
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Standard Preload (at Starting):
    Item
    Specified Condition
    New bearing
    0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf)
    Used bearing
    0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)

    1. If the preload is more than the maximum, replace the bearing spacer.
    1. If the preload is less than the minimum, retighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.

    Torque:
    457 N*m{ 4660 kgf*cm , 337 ft.*lbf } or less

    1. If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload adjusting procedure.

    HINT:
    Do not loosen the pinion nut to reduce the preload.



29. INSPECT TOTAL PRELOAD


    C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Total preload (at starting):
    Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)

    If necessary, disassemble and inspect the differential.



30. INSPECT DIFFERENTIAL RING GEAR BACKLASH


C216537
  1. Using a dial indicator, check the backlash of the ring gear.

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    1. If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

      HINT:
      Perform the measurement at 3 or more positions around the circumference of the ring gear.



31. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F001237E19
  1. Using a dial indicator, measure the runout of the drive pinion companion flange vertically and laterally.

    Distance from center to runout measurement point:
    30 mm (1.18 in.)

    Maximum Runout:
    Item
    Specified Condition
    Vertical runout
    0.14 mm (0.00551 in.)
    Lateral runout
    0.14 mm (0.00551 in.)

    Text in Illustration 
    *a
    Vertical Runout
    *b
    Lateral Runout
    1. If the runout is more than the maximum, replace the companion flange.



32. STAKE DRIVE PINION NUT


ZK07449E01
  1. Using a chisel and hammer, stake the nut.