Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.

  5. According to the display on the Techstream, read the Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Driver Side Seatbelt Warning Buzzer
    Driver side seat belt warning buzzer signal / ON or OFF
    ON: Seat belt warning buzzer enabled
    OFF: Seat belt warning buzzer disabled
    The current customize setting is displayed.
    P - Seatbelt Warning Buzzer
    Front passenger side seat belt warning buzzer signal / ON or OFF
    ON: Seat belt warning buzzer enabled
    OFF: Seat belt warning buzzer disabled
    The current customize setting is displayed.

    SRS Airbag 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Passenger Classification
    Front passenger side seat condition / NG, OFF, Child, AF05, AM50 or Fail
    NG: Condition undetermined
    OFF: Vacant
    Child: Child (32 kg [70.6 lb]) seated
    AF05: Adult (36 to 54 kg [79.4 to 119.1 lb]) seated
    AM50: Adult (more than 54 kg [119.1 lb]) seated
    Fail: Failure detected
    -
    Left side Buckle SW
    Front LH side seat belt buckle switch / Unset, Set or NG
    Unset: Seat belt unfastened
    Set: Seat belt fastened
    NG: Condition undetermined
    -
    Right side Buckle SW
    Front RH side seat belt buckle switch / Unset, Set or NG
    Unset: Seat belt unfastened
    Set: Seat belt fastened
    NG: Condition undetermined
    -

    Occupant Detection 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Passenger Buckle SW
    Front passenger side seat belt buckle switch / Unset, Set or NG
    Unset: Front passenger side seat belt unfastened
    Set: Front passenger side seat belt fastened
    NG: Condition undetermined
    -
    Passenger Classification
    Front passenger side seat condition / AM50, AF05, Child or OFF
    AM50: Adult (more than 54 kg [119.1 lb]) seated
    AF05: Adult (36 to 54 kg [79.4 to 119.1 lb]) seated
    Child: Child (less than 32 kg [70.5 lb]) seated
    OFF: Vacant
    -


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  5. According to display on the Techstream, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Driver Side Seat Belt
    Driver side seat belt warning light
    ON/OFF
    Confirm that the vehicle is stopped and the ignition switch ON.
    Front Passenger Side Seat Belt
    -
    -
    This item is not supported.