Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > TERMINALS OF ECU

for Preparation Click here



COMBINATION METER ASSEMBLY

E199754E01

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1 (CANH) - Body ground
    L - Body ground
    CAN communication signal
    Ignition switch off
    200 Ω or higher
    2 (CANL) - Body ground
    W - Body ground
    CAN communication signal
    Ignition switch off
    200 Ω or higher
    3 (MSSL) - Body ground
    P - Body ground
    Steering pad switch assembly (DISP switch) signal
    Ignition switch to ON, DISP switch not pressed
    4 to 5 V
    Ignition switch to ON, DISP switch pressed
    Below 1 V
    6 (LINT) - Body ground*1
    LG - Body ground
    LIN (Accessory meter communication)
    Ignition switch ON
    Pulse generation
    7 (RR) - Body ground*2
    Y - Body ground
    No. 1 Ultrasonic sensor (for rear corner RH)
    Clearance warning indication for rear corner RH is displayed
    Below 3 V
    8 (S) - Body ground
    V - Body ground
    Oil pressure switch signal
    Ignition switch ON, oil pressure warning light off
    11 to 14 V
    Ignition switch ON, oil pressure warning light on
    Below 1 V
    9 (TIRE) - Body ground
    G - Body ground
    Tire pressure warning light signal
    Ignition switch ON, tire pressure warning light off
    11 to 14 V
    Ignition switch ON, tire pressure warning light blinking
    Below 1 V
    10 (IL2-) - Body ground
    GR - Body ground
    Illumination signal
    Light control switch off
    Below 1 V
    Light control switch in tail or head position
    Pulse generation
    11 (ILL-) - Body ground
    GR - Body ground
    Illumination signal
    Light control switch off
    Below 1 V
    Light control switch in tail or head position
    Pulse generation
    12 (RL) - Body ground*2
    GR - Body ground
    No. 1 Ultrasonic sensor (for rear corner LH)
    Clearance warning indication for rear corner LH is displayed
    Below 3 V
    13 (MGND) - Body ground
    W-B - Body ground
    Ground (Signal ground)
    Always
    Below 1 V
    15 (B) - Body ground
    L - Body ground
    Battery
    Always
    11 to 14 V
    17 (IG+) - Body ground
    R - Body ground
    Ignition switch signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    18 (BK) - Body ground*2
    SB - Body ground
    No. 1 Ultrasonic sensor (for rear corner LH and RH)
    Clearance warning indication for back right and left sensor are displayed
    Below 3 V
    19 (E3) - Body ground
    B - Body ground
    Ground (Fuel ground)
    Always
    Below 1 V
    20 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    21 (STP+) - Body ground*3
    G - Body ground
    Automatic Running Boards warning light signal
    Automatic Running Boards warning light on or blinking
    11 to 14 V
    Automatic Running Boards warning light off
    Below 1 V
    22 (STPA) - Body ground*3
    W - Body ground
    Ground
    Automatic Running Boards warning light off
    11 to 14 V
    Ignition switch ON, automatic running boards warning light on
    Below 1 V
    23 (MSCH) - Body ground*4
    LG - Body ground
    CAN communication signal
    Ignition switch off
    200 Ω or higher
    24 (MSCL) - Body ground*4
    W - Body ground
    CAN communication signal
    Ignition switch off
    200 Ω or higher
    25 (B) - Body ground
    SB - Body ground
    Turn indicator light signal
    Ignition switch ON, turn RH indicator light off
    Below 1 V
    Ignition switch ON, turn RH indicator light blinking
    11 to 14 V
    26 (CHG-) - Body ground
    P - Body ground
    Charge warning light signal
    Ignition switch ON, charge warning light off
    11 to 14 V
    Ignition switch ON, charge warning light on
    Below 1 V
    27 (WLVL) - Body ground*5
    R - Body ground
    Washer level warning switch signal
    Ignition switch ON, washer level warning light off
    11 to 14 V
    Ignition switch ON, washer level warning light on
    Below 1 V
    28 (+S) - Body ground
    SB - Body ground
    Speed signal for other systems (Output)
    Driving at approx. 20 km/h (12 mph)
    Pulse generation (See waveform 1)
    29 (SI) - Body ground
    G - Body ground
    Speed signal for other systems (Input)
    Driving at approx. 20 km/h (12 mph)
    Pulse generation (See waveform 1)
    30 (CHK) - Body ground
    L - Body ground
    MIL (Check engine warning light) signal
    Ignition switch ON, MIL (Check engine warning light) off
    11 to 14 V
    Ignition switch ON, MIL (Check engine warning light) on
    Below 1 V
    31 (OP) - Body ground*2
    LG - Body ground
    Clearance warning ECU signal
    Clearance warning indication is displayed
    Below 3 V
    32 (FL) - Body ground*2
    P - Body ground
    No. 1 Ultrasonic sensor (for front corner LH)
    Clearance warning indication for front corner LH is displayed
    Below 3 V
    33 (B) - Body ground
    Y - Body ground
    Turn indicator light signal
    Ignition switch ON, turn LH indicator light off
    Below 1 V
    Ignition switch ON, turn LH indicator light blinking
    11 to 14 V
    35 (FR) - Body ground*2
    B - Body ground
    No. 1 Ultrasonic sensor (for front corner RH)
    Clearance warning indication for front corner RH is displayed
    Below 3 V
    36 (TC) - Body ground*6
    W - Body ground
    TAIL cancel switch signal
    TAIL cancel switch off
    1 MΩ or higher
    TAIL cancel switch on
    Below 1 Ω
    37 (RHIG) - Body ground*6
    B - Body ground
    Power source for light control rheostat
    Ignition switch ON
    4.6 to 5.4 V
    38 (TR) - Body ground*6
    GR - Body ground
    Light control rheostat signal
    Light control rheostat dial fully turned downward
    Below 1 Ω
    Light control rheostat dial fully turned upward
    8 to 12 kΩ
    39 (E2) - Body ground*6
    LG - Body ground
    Light control rheostat switch ground
    Always
    Below 1 Ω
    40 (L) - Body ground
    W - Body ground
    Fuel level signal
    Ignition switch ON, fuel level warning light off
    Below 4 V
    Ignition switch ON, fuel level warning light on
    4 to 9 V

    1. *1: w/ CRAWL Control
    2. *2: w/ Intuitive Parking Assist System
    3. *3: w/Automatic Running Board System
    4. *4: w/ Seat Position Memory
    5. *5: w/ Level Warning Switch Assembly
    6. *6: w/ Light Control Rheostat



  2. I043789E03
  3. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Condition
    Tool setting
    5 V/DIV., 20 ms./DIV.
    Vehicle condition
    Driving at approx. 20 km/h (12 mph)

    HINT:
    When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


ACCESSORY METER ASSEMBLY

E239700E01


Text in Illustration 
*A
w/ CRAWL Control
*B
w/o CRAWL Control
  1. Measure the voltage and resistance according to the value(s) in the table below.

    w/ CRAWL Control 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G3-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    G3-4 (DAT2) - Body ground
    LG - Body ground
    LIN communication signal
    Ignition switch ON
    Pulse generation
    G3-5 (IG+) - Body ground
    L - Body ground
    Ignition switch signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    G3-6 (ACC) - Body ground
    P - Body ground
    Ignition switch signal
    Ignition switch off
    Below 1 V
    Ignition switch ACC
    11 to 14 V
    G3-7 (B) - Body ground
    L - Body ground
    Battery
    Always
    11 to 14 V
    G4-1 (ILL+) - Body ground
    G - Body ground
    Illumination signal
    Light control switch in tail or head position
    11 to 14 V
    G4-4 (ILL-) - Body ground
    GR - Body ground
    Illumination signal
    Light control switch off
    Below 1 V
    Ignition switch ON, light control switch in tail or head position
    Pulse generation

    w/o CRAWL Control 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G36-1 (B) - Body ground
    L - Body ground
    Battery
    Always
    11 to 14 V
    G36-2 (ACC) - Body ground
    P - Body ground
    Ignition switch signal
    Ignition switch off
    Below 1 V
    Ignition switch ACC
    11 to 14 V
    G36-3 (ILL+) - Body ground
    G - Body ground
    Illumination signal
    Light control switch in tail or head position
    11 to 14 V
    G36-7 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω