AUTOMATIC TRANSMISSION UNIT > INSPECTION |
| 1. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY |
Remove the magnets and use them to collect steel particles.
Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.
| 2. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY |
![]() |
Hold the reverse clutch hub and turn the 1-way clutch assembly.
Check that the 1-way clutch turns freely when turned clockwise and locks when turned counterclockwise.
![]() | Lock |
![]() | Free |
| 3. INSPECT REAR CLUTCH DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 4. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.
| 5. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the forward clutch hub bush.
| 6. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 7. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 8. INSPECT DIRECT CLUTCH DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 9. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 10. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 11. INSPECT NO. 3 BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 12. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 13. INSPECT FRONT PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the front planetary pinion gear thrust clearance.
![]() |
Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.
| 14. INSPECT 1-WAY CLUTCH ASSEMBLY |
![]() |
Install the 1-way clutch to the 1-way clutch inner race.
![]() | Lock |
![]() | Free |
Hold the 1-way clutch inner race and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely when turned counterclockwise and locks when turned clockwise.
Remove the 1-way clutch from the 1-way clutch inner race.
| 15. INSPECT NO. 1 BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 16. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 17. INSPECT NO. 2 BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 18. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 19. INSPECT CENTER PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the center planetary pinion gear thrust clearance.
| 20. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY |
![]() |
Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely when turned counterclockwise and locks when turned clockwise.
![]() | Lock |
![]() | Free |
| 21. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the rear planetary ring gear bush.
| 22. INSPECT INTERMEDIATE SHAFT |
![]() |
Using a dial indicator, measure the intermediate shaft runout.
![]() |
Using a micrometer, measure the diameter of the intermediate shaft at the positions shown in the diagram.
| 23. INSPECT NO. 4 BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 24. INSPECT REAR PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the rear planetary pinion gear thrust clearance.
![]() |
Using a dial indicator, measure the inside diameter of the rear planetary gear bush.
| 25. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 26. INSPECT 1ST AND REVERSE BRAKE |
![]() |
Make sure the 1st and reverse brake piston moves smoothly when applying compressed air into and releasing compressed air from the transmission case.
| 27. INSPECT NO. 1 BRAKE |
![]() |
Make sure the No. 1 brake piston moves smoothly when applying compressed air into and releasing compressed air from the transmission case.
| 28. INSPECT INDIVIDUAL PISTON OPERATION |
![]() |
Check the operating sound while applying compressed air into the oil holes indicated in the illustration.