Home › Drivetrain ยท A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT

AUTOMATIC TRANSMISSION UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH


C212489
  1. Remove the nut, spring washer and control shaft lever LH.



2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


D027903E01
  1. Using a screwdriver, bend the tabs of the lock washer.

  1. Remove the nut, lock washer and bolt.

  1. Remove the park/neutral position switch.



3. REMOVE OIL COOLER TUBE UNION


C214945
  1. Remove the 2 oil cooler tube unions.

  1. Remove the 2 O-rings from the oil cooler tube unions.



4. REMOVE SPEED SENSOR


C111258
  1. Remove the 2 bolts and 2 speed sensors.

  1. Remove the 2 O-rings from the sensors.



5. REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE


C212491
  1. Remove the 2 bolts.

  1. Remove the breather tube.

  1. Remove the O-ring from the tube.



6. REMOVE AUTOMATIC TRANSMISSION HOUSING


C210181
  1. Remove the 10 bolts.

  1. Remove the transmission housing.



7. REMOVE EXTENSION HOUSING SUB-ASSEMBLY


D027972E01
  1. Remove the 6 bolts.

  1. Remove the extension housing.

    HINT:
    Use a brass bar and hammer to remove the extension housing.



    D029874E01
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the thrust needle roller bearing and 2 bearing races.

  1. Remove the 2 transfer case ring pins from the transmission case adapter.



8. REMOVE EXTENSION HOUSING DUST DEFLECTOR


D027976E01
  1. Using a brass bar and hammer, tap out the dust deflector.



9. REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL


D027977E02
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  



10. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY


D027911E01
  1. Install the transmission case to an overhaul attachment.



11. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

NOTICE:
Do not turn the transmission over as this will contaminate the valve body with foreign matter in the bottom of the pan.

  1. Remove the drain plug and 20 bolts.

  1. Remove the 4 magnets from the oil pan.



12. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
  1. Remove the magnets and use them to collect steel particles.

  1. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear
    2. Brass (non-magnetic): bush wear



13. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


D012703E01
  1. Turn over the transmission.

  1. Remove the 4 bolts and oil strainer from the valve body.

  1. Remove the O-ring from the oil strainer.



14. REMOVE TRANSMISSION WIRE


D012704E05
  1. Remove the 2 bolts and 2 temperature sensor clamps, and disconnect the 2 ATF temperature sensors.
    Text in Illustration 
    *1
    Temperature Sensor Clamp

  1. Disconnect the 7 connectors from the solenoid valves.



    D027912E01
  1. Remove the bolt from the case.

  1. Pull the transmission wire out of the transmission case to remove it.

  1. Remove the O-ring from the transmission wire.



15. REMOVE TRANSMISSION VALVE BODY ASSEMBLY
  1. Remove the bolt, detent spring cover and detent spring.



    C157292E02
  1. Remove the 19 bolts and valve body.



16. REMOVE TRANSMISSION CASE GASKET


D027968E03
  1. Remove the 3 gaskets.



17. REMOVE BRAKE DRUM GASKET


D027969E01
  1. Remove the 3 gaskets.



18. REMOVE CHECK BALL BODY


D027914E13
  1. Remove the check ball body and spring.
    Text in Illustration 
    *1
    Check Ball Body
    *2
    Spring



19. REMOVE C-2 ACCUMULATOR PISTON


D027915E01
  1. Apply compressed air to the oil hole to remove the C-2 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.

    NOTICE:
    Be careful as the C-3 and B-3 accumulator pistons may jump out.



20. REMOVE B-3 ACCUMULATOR PISTON


D027915E01
  1. Apply compressed air to the oil hole to remove the B-3 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.

    NOTICE:
    Be careful as the C-3 accumulator piston may jump out.



21. REMOVE C-3 ACCUMULATOR PISTON


D027916E01
  1. Apply compressed air to the oil hole to remove the C-3 accumulator piston and 2 springs.

  1. Remove the 2 O-rings from the piston.



22. REMOVE C-1 ACCUMULATOR VALVE


D027917E01
  1. Remove the C-1 accumulator valve and 2 springs.



23. REMOVE PARKING LOCK PAWL BRACKET


D012708E02
  1. Remove the 3 bolts and bracket.



24. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


D012709E01
  1. Disconnect the parking lock rod from the manual valve lever to remove it.



25. REMOVE PARKING LOCK PAWL SHAFT


D028846E01
  1. Pull out the parking lock pawl shaft from the front side to remove it, and then remove the lock pawl and spring.

  1. Remove the E-ring from the shaft.



26. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


D027918E01
  1. Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.



    D027919E01
  1. Using a pin punch and hammer, tap out the spring pin.

    HINT:
    Slowly drive out the spring pin so that it does not fall into the transmission case.

  1. Pull the manual valve lever shaft out through the case and remove the manual valve lever.



27. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


D027920E02
  1. Using a screwdriver, pry out the 2 oil seals.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the transmission case.



28. REMOVE OIL PUMP ASSEMBLY


D027921E01
  1. Remove the 10 bolts.



    D027922E02
  1. Using SST, remove the oil pump.

    SST
    09350-30020   (09350-07020)



    D028796E03
  1. Remove the O-ring from the front oil pump.



    C177431
  1. Remove the 2 thrust bearing races from the front oil pump.



29. REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


D027923E01
  1. Remove the clutch drum and input shaft assembly from the transmission case.



    C177432
  1. Remove the clutch drum thrust washer and 2 thrust needle roller bearings.



30. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY


D027993E04
  1. Hold the reverse clutch hub and turn the 1-way clutch assembly.

  1. Check that the 1-way clutch turns freely when turned clockwise and locks when turned counterclockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free



31. REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY


D027994E01
  1. Remove the 1-way clutch and No. 2 clutch drum thrust washer from the clutch drum and input shaft assembly.



32. FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


D027995E02
  1. Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft assembly onto the oil pump.
    Text in Illustration 
    *1
    Torque Converter Clutch
    *2
    Oil Pump



33. REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY


D027996E01
  1. Using a screwdriver, remove the snap ring.



    D027997E01
  1. Remove the reverse clutch hub sub-assembly, reverse clutch reaction sleeve, clutch cushion, plate reverse clutch flange, 5 reverse clutch discs and 4 clutch plates from the clutch drum.



34. REMOVE REVERSE CLUTCH REACTION SLEEVE


D027998E01
  1. Remove the reverse clutch reaction sleeve from the reverse clutch hub.



35. REMOVE REAR CLUTCH DISC
  1. Remove the clutch cushion plate, reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.



36. INSPECT REAR CLUTCH DISC


C171511
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



37. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY


D028000E01
  1. Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.

    Standard inside diameter:
    35.812 to 35.837 mm (1.410 to 1.411 in.)

    Maximum inside diameter:
    35.887 mm (1.413 in.)

    1. If the inside diameter is more than the maximum, replace the reverse clutch hub.



38. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY


D028001E01
  1. Remove the forward clutch hub from the clutch drum.



    D028500E03
  1. Remove the 2 thrust needle roller bearings from the forward clutch hub.



39. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY


D028501E01
  1. Using a dial indicator, measure the inside diameter of the forward clutch hub bush.

    Standard inside diameter:
    26.037 to 26.062 mm (1.025 to 1.026 in.)

    Maximum inside diameter:
    26.112 mm (1.028 in.)

    1. If the inside diameter is more than the maximum, replace the forward clutch hub.



40. REMOVE MULTIPLE DISC CLUTCH HUB


D028502E01
  1. Remove the multiple disc clutch hub from the clutch drum.



    D028503E07
  1. Remove the 2 thrust bearing races from the multiple disc clutch hub.



41. REMOVE INPUT SHAFT ASSEMBLY


D028504E01
  1. Remove the thrust needle roller bearing from the clutch drum.



    D028505E01
  1. Remove the input shaft assembly from the clutch drum.



42. REMOVE INPUT SHAFT OIL SEAL RING


D029677E01
  1. Remove the 3 oil seal rings from the input shaft.



43. REMOVE FORWARD MULTIPLE DISC CLUTCH DISC


D028519E01
  1. Using a screwdriver, remove the hole snap ring.

  1. Remove the 2 flanges, 6 discs and 5 plates from the input shaft.



44. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC


C171513
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



45. REMOVE NO. 1 CLUTCH BALANCER


D028521E02
  1. Place SST on the clutch balancer and compress the return spring with a press.

    SST
    09350-30020   (09350-07040, 09350-07070)

  1. Using a snap ring expander, remove the snap ring.



    D028522E01
  1. Remove the clutch balancer and forward clutch return spring from the input shaft assembly.



    D028523E01
  1. Remove the O-ring from the No. 1 clutch balancer.



46. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


C171515
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    26.74 mm (1.05 in.)



47. REMOVE FORWARD CLUTCH PISTON


D028524E01
  1. Hold the input shaft by hand and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the input shaft to remove the forward clutch piston.



    D028525E01
  1. Remove the 2 O-rings from the forward clutch piston.



48. REMOVE REVERSE CLUTCH FLANGE


D028506E01
  1. Remove the reverse clutch flange from the clutch drum.



49. REMOVE DIRECT CLUTCH DISC


D028507E01
  1. Using a screwdriver, remove the 2 hole snap rings from the clutch drum.

  1. Remove the reverse clutch flange, 5 discs and 5 plates from the clutch drum.



50. INSPECT DIRECT CLUTCH DISC


C171512
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



51. REMOVE NO. 3 CLUTCH BALANCER


D028509E04
  1. Place SST on the clutch balancer and compress the return spring with a press.

    SST
    09387-00070  

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)



52. REMOVE REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


D028510E01
  1. Remove the reverse clutch return spring and O-ring from the reverse clutch piston.



53. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


C171517
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.04 mm (0.828 in.)



54. REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY


D028511E01
  1. Remove the reverse clutch piston sub-assembly from the clutch drum.



    D028512E01
  1. Remove the O-ring from the reverse clutch piston.



    D028513E01
  1. Remove the O-ring from the clutch drum.



55. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


D028514E06
  1. Place SST on the direct clutch piston and compress the return spring with a press.

    SST
    09320-89010  

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)



    D028515E01
  1. Using 2 screwdrivers, remove the direct clutch piston sub-assembly from the clutch drum.



    D028517E01
  1. Remove the No. 2 clutch balancer and direct clutch return spring from the direct clutch piston.



    D028816E01
  1. Remove the 2 O-rings from the direct clutch piston.



56. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


C171516
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.51 mm (0.768 in.)



57. REMOVE NO. 3 BRAKE SNAP RING


D027925E01
  1. Using a screwdriver, remove the No. 3 brake snap ring from the case.



58. REMOVE NO. 3 BRAKE DISC
  1. Remove the flange, 4 discs, 4 plates and cushion plate from the case.



59. INSPECT NO. 3 BRAKE DISC


C161778
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



60. REMOVE 2ND BRAKE PISTON HOLE SNAP RING


D027927E03
  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07060)



61. REMOVE 1-WAY CLUTCH ASSEMBLY


D027928E01
  1. Remove the 1-way clutch assembly and No. 1 planetary carrier thrust washer from the case.



62. REMOVE 2ND BRAKE CYLINDER


D027929E01
  1. Remove the 2nd brake cylinder from the case.



63. REMOVE 2ND BRAKE PISTON


D028817E05
  1. Using SST and a press, compress the return spring and remove the snap ring.

    SST
    09351-40010  



    D028545E01
  1. Hold the 2nd brake cylinder and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the 2nd brake cylinder to remove the 2nd brake piston.



    D028546E03
  1. Remove the 2 O-rings from the 2nd brake piston.



64. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C171518
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.72 mm (0.619 in.)



65. REMOVE FRONT PLANETARY GEAR ASSEMBLY


D027930E01
  1. Remove the 1-way clutch inner race and front planetary gear assembly from the case.



    D027931E03
  1. Remove the thrust bearing race, thrust needle roller bearing and No. 2 planetary carrier thrust washer from the front planetary gear assembly.



66. INSPECT FRONT PLANETARY GEAR ASSEMBLY


D028544E01
  1. Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00787 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    1. If the clearance is more than the maximum, replace the front planetary gear assembly.



    D028543E01
  1. Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.

    Maximum inside diameter:
    57.48 mm (2.26 in.)

    1. If the inside diameter is more than the maximum, replace the front planetary gear.



67. INSPECT 1-WAY CLUTCH ASSEMBLY


D028542E04
  1. Install the 1-way clutch to the 1-way clutch inner race.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free

  1. Hold the 1-way clutch inner race and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely when turned counterclockwise and locks when turned clockwise.

  1. Remove the 1-way clutch from the 1-way clutch inner race.



68. REMOVE FRONT PLANETARY RING GEAR


D027932E01
  1. Remove the front planetary ring gear and thrust needle roller bearing from the transmission case.



69. REMOVE CENTER PLANETARY RING GEAR


D028540E01
  1. Using a screwdriver, remove the snap ring.



    D028541E01
  1. Remove the center planetary ring gear and front planetary ring gear flange from the front planetary ring gear.



70. REMOVE NO. 1 BRAKE DISC
  1. Remove the flange, 3 discs and 3 plates from the case.



71. INSPECT NO. 1 BRAKE DISC


C171514
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



72. REMOVE BRAKE PISTON RETURN SPRING SNAP RING


D027934E01
  1. Using a screwdriver, remove the brake piston return spring snap ring from the case.



73. REMOVE BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


D027935E01
  1. Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.



74. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C171519
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.05 mm (0.671 in.)



75. REMOVE NO. 1 BRAKE PISTON


D027936E01
  1. Hold the No. 1 brake cylinder and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the No. 1 brake cylinder to remove the No. 1 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the 2 O-rings from the No. 1 brake piston.



76. REMOVE NO. 2 BRAKE DISC


D027937E01
  1. Using a screwdriver, remove the snap ring from the case.

  1. Remove the flange, 3 discs, 3 plates and brake piston return spring from the case.



77. INSPECT NO. 2 BRAKE DISC


C161770
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



78. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C171520
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.45 mm (0.687 in.)



79. REMOVE NO. 2 BRAKE PISTON


D027939E01
  1. Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the transmission case to remove the No. 2 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the 2 O-rings from the No. 2 brake piston.



80. REMOVE CENTER PLANETARY GEAR ASSEMBLY


D027940E01
  1. Remove the thrust bearing race, center planetary gear and planetary sun gear from the case.



81. INSPECT CENTER PLANETARY GEAR ASSEMBLY


D028533E01
  1. Using a feeler gauge, measure the center planetary pinion gear thrust clearance.

    Standard clearance:
    0.12 to 0.68 mm (0.00472 to 0.0268 in.)

    Maximum clearance:
    0.73 mm (0.0287 in.)

    1. If the clearance is more than the maximum, replace the center planetary gear assembly.



82. REMOVE INTERMEDIATE SHAFT


D027941E01
  1. Using a screwdriver, remove the snap ring from the case.



    D027942E01
  1. Remove the intermediate shaft with No. 3 1-way clutch assembly from the case.



83. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY


D028532E04
  1. Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely when turned counterclockwise and locks when turned clockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free



84. REMOVE NO. 3 1-WAY CLUTCH ASSEMBLY


D027964E01
  1. Remove the No. 3 1-way clutch assembly and 1-way clutch inner race from the intermediate shaft.



85. REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY


D027965E12
  1. Remove the planetary ring gear flange, 2 thrust bearing races and thrust needle roller bearing from the intermediate shaft.



86. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY


D028531E01
  1. Using a dial indicator, measure the inside diameter of the rear planetary ring gear bush.

    Standard inside diameter:
    32.176 to 32.201 (1.267 to 1.268 in.)

    Maximum inside diameter:
    32.251 mm (1.270 in.)

    1. If the inside diameter is more than the maximum, replace the rear planetary ring gear.



87. INSPECT INTERMEDIATE SHAFT


D028529E04
  1. Using a dial indicator, measure the intermediate shaft runout.

    Standard runout:
    0.03 mm (0.00118 in.)

    Maximum runout:
    0.08 mm (0.00315 in.)

    If the runout is more than the maximum, replace the intermediate shaft with a new one.



    D028530E02
  1. Using a micrometer, measure the diameter of the intermediate shaft at the positions shown in the diagram.

    Standard diameter:
    A, B:
    25.962 to 25.975 mm (1.022 to 1.023 in.)
    C, D:
    32.062 to 32.075 mm (1.262 to 1.263 in.)

    Minimum diameter:
    A, B:
    25.912 mm (1.02 in.)
    C, D:
    32.012 mm (1.26 in.)

    If the diameter is less than the minimum, replace the intermediate shaft with a new one.



88. REMOVE BRAKE PLATE STOPPER SPRING


D027943E01


89. REMOVE NO. 4 BRAKE DISC
  1. Remove the 7 plates, 8 discs and 2 flanges from the case.



90. INSPECT NO. 4 BRAKE DISC


C161745
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.



91. REMOVE REAR PLANETARY GEAR ASSEMBLY


C161737
  1. Remove the rear planetary gear assembly from the case.



    C161738
  1. Remove the 2 thrust needle roller bearings from the rear planetary gear.



    D027947E02
  1. Remove the thrust bearing race from the case.



92. INSPECT REAR PLANETARY GEAR ASSEMBLY


C190073
  1. Using a feeler gauge, measure the rear planetary pinion gear thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00787 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    1. If the clearance is more than the maximum, replace the planetary gear assembly.



    C190074
  1. Using a dial indicator, measure the inside diameter of the rear planetary gear bush.

    Maximum inside diameter:
    20.075 mm (0.790 in.)

    1. If the inside diameter is more than the maximum, replace the rear planetary gear assembly.



93. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


D028083E03
  1. Place SST on the spring retainer and compress the brake return spring.

    SST
    09350-30020   (09350-07050)
    Text in Illustration 
    *1
    Snap Ring

  1. Using SST, remove the snap ring and brake return spring.

    SST
    09350-30020   (09350-07070)



94. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C171521
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    23.74 mm (0.935 in.)



95. REMOVE 1ST AND REVERSE BRAKE PISTON


D027948E01
  1. Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the transmission case to remove the 1st and reverse brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the O-ring from the 1st and reverse brake piston.



96. REMOVE BRAKE REACTION SLEEVE


D028079E04
  1. Using SST, remove the reaction sleeve.

    SST
    09350-30020   (09350-07080)

  1. Remove the 2 O-rings from the reaction sleeve.



97. REMOVE NO. 4 BRAKE PISTON


D001240E03
  1. Using SST, remove the brake piston.

    SST
    09350-30020   (09350-07090)

  1. Remove the 2 O-rings from the brake piston.