Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK COMBINATION METER ASSEMBLY

E161130E13

  1. Disconnect the F14 combination meter assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F14-15 (B) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    F14-17 (IG+) - Body ground
    R - Body ground
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    F14-20 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK CENTER AIRBAG SENSOR ASSEMBLY

C109532E34


Terminal No.
Symbol
Description
O1-10
LBE+
Front seat inner belt assembly LH (Seat belt buckle switch LH)
O1-18
LBE-
Front seat inner belt assembly LH (Seat belt buckle switch LH)
N1-16
FSR+
Occupant detection ECU
N1-24
FSR-
Occupant detection ECU

CHECK OCCUPANT DETECTION ECU
If the result is not as specified, the occupant detection ECU may have a malfunction.

H100909E32


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
a9-1 (+B) - a9-3 (GND)
W - W-B
Battery power supply
Always
11 to 14 V
a9-2 (DIA) - a9-3 (GND)
GR - W-B
Diagnosis (DLC3)
Ignition switch ON
Pulse generation
a9-3 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 V
a9-4 (FSR-) - a9-3 (GND)
LG - W-B
Center airbag sensor assembly communication line
Always
Below 1 V
a9-5 (BGND) - a9-3 (GND)
P - W-B
Front passenger side buckle switch ground line
Always
Below 1 V
a9-7 (IG2) - a9-3 (GND)
B - W-B
Ignition switch power supply
Ignition switch ON
11 to 14 V
a9-8 (FSR+) - a9-4 (FSR-)
L - LG
Center airbag sensor assembly communication line
Ignition switch ON
Pulse generation
a9-9 (BSW) - a9-5 (BGND)
G - P
Front passenger side buckle switch line
Always
Pulse generation
a10-1 (SGD1) - a9-3 (GND)
G - W-B
Front occupant classification sensor LH ground line
Always
Below 1 V
a10-2 (SGD2) - a9-3 (GND)
LG - W-B
Front occupant classification sensor RH ground line
Always
Below 1 V
a10-3 (SGD3) - a9-3 (GND)
W - W-B
Rear occupant classification sensor LH ground line
Always
Below 1 V
a10-4 (SGD4) - a9-3 (GND)
BR - W-B
Rear occupant classification sensor RH ground line
Always
Below 1 V
a10-11 (SVC1) - a10-1 (SGD1)
R - G
Front occupant classification sensor LH power supply line
Ignition switch ON, load applied to front occupant classification sensor LH
4.9 to 5.1 V
a10-12 (SVC2) - a10-2 (SGD2)
W - LG
Front occupant classification sensor RH power supply line
Ignition switch ON, load applied to front occupant classification sensor RH
4.9 to 5.1 V
a10-5 (SVC3) - a10-3 (SGD3)
GR - W
Rear occupant classification sensor LH power supply line
Ignition switch ON, load applied to rear occupant classification sensor LH
4.9 to 5.1 V
a10-6 (SVC4) - a10-4 (SGD4)
V - BR
Rear occupant classification sensor RH power supply line
Ignition switch ON, load applied to rear occupant classification sensor RH
4.9 to 5.1 V
a10-7 (SIG1) - a10-1 (SGD1)
P - G
Front occupant classification sensor LH signal line
Ignition switch ON, load applied to front occupant classification sensor LH
0 to 5.1 V
a10-8 (SIG2) - a10-2 (SGD2)
L - LG
Front occupant classification sensor RH signal line
Ignition switch ON, load applied to front occupant classification sensor RH
0 to 5.1 V
a10-9 (SIG3) - a10-3 (SGD3)
SB - W
Rear occupant classification sensor LH signal line
Ignition switch ON, load applied to rear occupant classification sensor LH
0 to 5.1 V
a10-10 (SIG4) - a10-4 (SGD4)
B - BR
Rear occupant classification sensor RH signal line
Ignition switch ON, load applied to rear occupant classification sensor RH
0 to 5.1 V