Home › Drivetrain ยท AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > DISASSEMBLY

for Preparation Click here



1. INSPECT DIFFERENTIAL RING GEAR BACKLASH


R012683E01
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-32011  

    Standard backlash:
    0.11 to 0.21 mm (0.00433 to 0.00827 in.)

    If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

    HINT:
    Perform the measurement at 3 or more positions around the circumference of the ring gear.



2. INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F001237E16
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Distance from center to runout measurement point:
    30 mm (1.18 in.)

    Maximum Runout:
    Item
    Specified Condition
    Vertical runout
    0.15 mm (0.00591 in.)
    Lateral runout
    0.15 mm (0.00591 in.)

    Text in Illustration 
    *a
    Vertical Runout
    *b
    Lateral Runout
    If the runout is more than the maximum, replace the companion flange.



3. REMOVE DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY (w/ A.D.D.)


    G023135
  1. Remove the 4 bolts.

  1. Using a hammer handle, pry out the actuator from the differential tube.



4. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY


    C097021
  1. Using an E14 "TORX" socket wrench, remove the 4 bolts.

  1. Using a plastic-faced hammer, tap out the differential tube.



5. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    R013209E01
  1. Using SST, remove the 2 oil seals.

    SST
    09308-00010  



6. REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY (w/ A.D.D.)


    G023136E02
  1. Using SST, remove the side gear inter shaft.

    SST
    09350-20015   (09369-20040)
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)

  1. Remove the snap ring from the side gear inter shaft.



7. REMOVE FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR (w/ A.D.D.)


G023164E02
  1. Using a screwdriver pry out the bearing retainer deflector.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *a
    Protective Tape



8. REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT


F044234E01
  1. Using SST and a hammer, unstake the nut.

    SST
    09930-00010  



    SA02349E05
  1. Using SST to hold the companion flange, remove the nut.

    SST
    09330-00021  



9. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F052175E06
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



10. REMOVE FRONT DIFFERENTIAL DUST DEFLECTOR


F040564E02
  1. Using SST and a press, press out the dust deflector.

    SST
    09950-00020  
    09950-60010   (09951-00510)
    09950-70010   (09951-07150)

    NOTICE:
    Do not drop the companion flange.



11. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL


    SA02348E08
  1. Using SST, remove the oil seal from the differential carrier assembly.

    SST
    09308-10010  
    Text in Illustration 
    *a
    Hold
    *b
    Turn



12. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
  1. Remove the oil slinger from the drive pinion.



13. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)


    F044343E03
  1. Using SST, remove the front tapered roller bearing (inner) from the drive pinion.

    SST
    09556-22010  



14. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)


    W001770E06
  1. Using SST, remove the front tapered roller bearing (outer).

    SST
    09308-00010  



15. REMOVE FRONT DIFFERENTIAL OIL STORAGE RING
  1. Using a screwdriver and hammer, tap out the oil storage ring.



16. REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER


C093595
  1. Remove the bearing spacer.



17. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
  1. Using a screwdriver, remove the union.

  1. Remove the 10 bolts and tap out the side bearing retainer with a plastic-faced hammer.



18. REMOVE DIFFERENTIAL CASE ASSEMBLY


19. REMOVE DIFFERENTIAL DRIVE PINION


20. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (INNER)


    R002482E02
  1. Using SST and a press, remove the rear tapered roller bearing (inner) and washer from the drive pinion.

    SST
    09950-00020  

    NOTICE:
    Do not drop the drive pinion.

    HINT:
    If the drive gear or ring gear is damaged, replace them as a set.



21. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (OUTER)


    R013226
  1. Using a brass bar and hammer, remove the rear tapered roller bearing (outer).



22. REMOVE FRONT DIFFERENTIAL CASE BEARING


R013211E01

HINT:
  1. Measure the thickness of the case washer.
  2. Tag the bearing outer races so that they can be reinstalled in the correct locations.

  1. Using SST and a press, press out the case bearing (outer race) and case washer from the bearing retainer.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)
    If the bearing is damaged during removal, replace it.



    R013213E01
  1. Using SST and a press, press out the case bearing (outer race) and plate washer from the differential carrier.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)
    If the bearing is damaged during removal, replace it.



23. REMOVE DIFFERENTIAL RING GEAR


C113176E02
  1. Place matchmarks on the ring gear and differential case.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 10 ring gear set bolts.



    C014054E01
  1. Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.



24. REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:
The differential case and case bearings should only be removed when replacement is necessary.



    R011392E03
  1. Using SST, remove the 2 differential case bearings (inner) from the differential case.

    SST
    09950-60010   (09951-00390)
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Notch

    HINT:
    Set the claws of SST into the notches in the differential case.



25. REMOVE DIFFERENTIAL CASE ASSEMBLY


    C080046E01
  1. Using a chisel and hammer, unstake the differential case.



    G020264E01
  1. Using a 5 mm pin punch and hammer, tap out the straight pin.



    C216791E01
  1. Remove the parts shown in the illustration from the differential case.
    Text in Illustration 
    *1
    Differential Pinion Gear
    *2
    Differential Pinion Gear Thrust Washer
    *3
    Differential Pinion Shaft
    *4
    Differential Side Gear
    *5
    Differential Side Gear Thrust Washer



26. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that the differential pinion and differential side gear are not damaged.
    If the differential pinion or differential side gear is damaged, replace the differential gear kit.



27. INSPECT FRONT DIFFERENTIAL CASE
  1. Check that the differential case is not damaged.
    If the differential case is damaged, replace it.



28. REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING (w/ A.D.D.)


    SA00353
  1. Using a brass bar and hammer, tap out the 2 bearings.



29. REMOVE DIFFERENTIAL CLUTCH HUB (w/ A.D.D.)


    G023137
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the differential clutch hub.



30. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    R013199E01
  1. Using SST, tap out the oil seal from the differential tube.

    SST
    09308-00010  



31. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH


    C097022
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the side gear shaft from the differential tube.



32. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH


    R013420E02
  1. Using a snap ring expander, remove the snap ring.

  1. Using SST, a brass bar and press, press out the bearing.

    SST
    09950-00020  

    NOTICE:
    1. Do not damage the bearing.
    2. Do not drop the shaft.



33. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB (w/ A.D.D.)


G023141
  1. Check that there is no wear or damage to the clutch hub and clutch sleeve.
    Replace parts as necessary.

  1. Check that the clutch sleeve slides smoothly on the clutch hub.
    Replace parts as necessary.



34. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL SIDE GEAR INTER SHAFT (w/ A.D.D.)


    G023144
  1. Check for wear and damage to the clutch hub and side gear inter shaft.
    Replace parts as necessary.

  1. Check that the clutch sleeve slides smoothly on the side gear inter shaft.
    Replace parts as necessary.



35. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE (w/ A.D.D.)


    G023142
  1. Using a feeler gauge, measure the clearance between the sleeve fork and clutch sleeve.

    Maximum clearance:
    0.15 to 0.35 mm (0.00591 to 0.0138 in.)

    If the clearance is more than the maximum, replace the fork or clutch sleeve.