Home › Drivetrain ยท VF2BM TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSFER CASE COVER SUB-ASSEMBLY


F043428E01
  1. Remove the 4 bolts and the transfer case cover sub-assembly.



2. REMOVE BREATHER OIL DEFLECTOR SUB-ASSEMBLY
  1. Remove the breather oil deflector sub-assembly.



3. REMOVE FRONT TRANSFER BEARING RETAINER SUB-ASSEMBLY


D029928E01
  1. Remove the 5 bolts and the front transfer bearing retainer sub-assembly.

    HINT:
    If necessary, tap the front transfer bearing retainer sub-assembly with a plastic-faced hammer to remove it.



4. REMOVE FRONT TRANSFER BEARING RETAINER OIL SEAL
  1. Using a screwdriver and hammer, remove the front transfer bearing retainer oil seal.



5. REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


D029929E01
  1. Using a chisel and hammer, loosen the staked part of the lock nut.

  1. Using SST to hold the front output shaft companion flange sub-assembly, remove the lock nut.

    SST
    09330-00021  



    D029930E01
  1. Using SST, remove the front output shaft companion flange sub-assembly.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



6. REMOVE FRONT TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
  1. Using a screwdriver and hammer, remove the front transfer output shaft companion flange oil seal.

    NOTICE:
    Be careful not to damage the oil seal and companion flange contact surfaces.



7. REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Remove the rear output shaft companion flange sub-assembly using the same procedure as for the front output shaft companion flange sub-assembly.

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



8. REMOVE REAR TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
  1. Using a screwdriver and hammer, remove the rear transfer output shaft companion flange oil seal.



9. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Remove the bolt and speedometer driven hole cover sub-assembly.

  1. Remove the O-ring from speedometer driven hole cover sub-assembly.



10. REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY


D029931E01
  1. Remove the 5 bolts and transfer extension housing sub-assembly.

    HINT:
    If necessary, tap the transfer extension housing sub-assembly with a plastic-faced hammer to remove it.



11. REMOVE TRANSFER CASE REAR OIL SEAL
  1. Using a screwdriver and hammer, remove the transfer case rear oil seal.



12. REMOVE TRANSFER OUTPUT SHAFT WASHER


    F043432E03
  1. Remove the 2 transfer output shaft washers.
    Text in Illustration 
    *1
    Collar
    *2
    Transfer Output Shaft Washer



13. REMOVE COLLAR
  1. Remove the collar.



14. REMOVE REAR TRANSFER CASE


C274518
  1. Remove the 12 bolts and clamp.

  1. Remove the rear transfer case.

    HINT:
    If necessary, tap the rear transfer case with a plastic-faced hammer to remove it.



15. REMOVE TRANSFER FRONT DRIVE SHIFT FORK SHAFT


D029933E01
  1. Using a hexagon wrench (6 mm), remove the 2 shift detent ball spring plugs, 2 shift fork compression springs and 2 shift detent balls.
    Text in Illustration 
    *1
    Shift Detent Ball
    *2
    Shift Fork Compression Spring
    *3
    Shift Detent Ball Spring Plug



    D029934
  1. Using 2 screwdrivers and a hammer, tap out the 2 transfer gear shift fork shaft snap rings.



    D029935
  1. Remove the bolt and transfer shift shaft stopper.



    D029936E02
  1. To pull out the transfer front drive shift fork shaft, shift the No. 1 and No. 2 transfer gear shift forks to the positions shown in the illustration.
    Text in Illustration 
    *1
    No. 2 Transfer Gear Shift Fork
    *2
    No. 1 Transfer Gear Shift Fork
    *3
    Transfer Front Drive Shift Fork Shaft
    *4
    Shift Fork Shaft Snap Ring

  1. Pull out the transfer front drive shift fork shaft.



    D029937
  1. Using a magnetic finger, remove the 2 shift inter lock pins.



16. REMOVE REAR OUTPUT SHAFT ASSEMBLY, FRONT DRIVE CHAIN, DRIVEN SPROCKET ASSEMBLY, NO. 1 AND NO. 2 TRANSFER GEAR SHIFT FORKS


D029938
  1. Using 2 screwdrivers and a hammer, tap out the transfer gear shift fork shaft snap ring.

    HINT:
    Remove only the transfer gear shift fork shaft snap ring on the front side of the transfer front drive shift fork shaft.



    D029939
  1. Using a snap ring expander, remove the transfer output shaft snap ring.



    D029940
  1. Mount the rear transfer case in a vise.

  1. Using a plastic-faced hammer, carefully tap the rear transfer case and remove the rear output shaft assembly, driven sprocket assembly, front drive chain, No. 1 and No. 2 transfer gear shift forks.

  1. Remove the driven sprocket assembly, front drive chain, No. 1 and No. 2 transfer gear shift forks from the rear output shaft assembly.



17. REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY


D029941
  1. Using 2 screwdrivers and a hammer, remove the transfer gear shift fork shaft snap ring.

  1. Remove the 3 bolts and transfer shift actuator assembly.



18. REMOVE NO. 1 TRANSFER INDICATOR SWITCH


D029942E01
  1. Remove the O-ring, the 2 No. 1 transfer indicator switches and 2 gaskets.
    Text in Illustration 
    *1
    No. 1 transfer indicator switch (L4 Position)
    *2
    No. 1 transfer indicator switch (4WD Position)



19. REMOVE TRANSFER DRIVEN SPROCKET BEARING


C216518E01
  1. Using SST and a press, remove the transfer driven sprocket bearing.

    SST
    09555-55010  



20. REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING


C216519E02
  1. Using SST, a press and steel bar, remove the transfer input gear radial ball bearing.

    SST
    09555-55010  
    Text in Illustration 
    *1
    Steel Bar



21. REMOVE FILLER PLUG
  1. Remove the filler plug and gasket.



22. REMOVE DRAIN PLUG
  1. Remove the drain plug and gasket.



23. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY


D029943
  1. Remove the 3 bolts and transfer oil separator sub-assembly.



24. REMOVE TRANSFER CASE MAGNET
  1. Remove the transfer case magnet.



25. REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY


D029944E01
  1. Remove the 3 bolts and transfer oil pump body sub-assembly.



26. REMOVE TRANSFER OIL PUMP GEAR
  1. Remove the transfer oil pump gear.



27. REMOVE TRANSFER OIL PUMP BODY O-RING


F043462
  1. Using a screwdriver, remove the transfer oil pump body O-ring.



28. REMOVE LOW PLANETARY GEAR ASSEMBLY WITH INPUT SHAFT SUB-ASSEMBLY


D029945
  1. Using a snap ring expander, remove the transfer low planetary gear bearing shaft snap ring.



    Q007221
  1. Remove the low planetary gear assembly w/ input shaft assembly.



29. REMOVE TRANSFER CASE PLUG


D029954E01
  1. Remove the transfer case plug.

  1. Using a magnetic finger, remove the transfer case compression spring and pin.
    Text in Illustration 
    *1
    Transfer Case Plug
    *2
    Transfer Case Compression Spring
    *3
    Pin



30. REMOVE TRANSFER LOW PLANETARY RING GEAR


D029953
  1. Using a screwdriver, remove the transfer low planetary ring gear hole snap ring.

  1. Remove the transfer low planetary ring gear from the front case.



31. REMOVE TRANSFER CASE FRONT OIL SEAL
  1. Using a screwdriver and hammer, remove the transfer case front oil seal.



32. REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE


TF00472
  1. Using a screwdriver, remove the transfer low planetary gear shaft snap ring.



    TF00473
  1. Remove the transfer low planetary gear spline piece.



33. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


TF00474
  1. Remove the 2 transfer output shaft front needle roller bearings.



34. REMOVE TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING


Q007289
  1. Using a snap ring expander, remove the transfer input gear stopper shaft snap ring.



35. REMOVE TRANSFER INPUT GEAR STOPPER


C216824E02
  1. Remove the transfer input gear stopper.
    Text in Illustration 
    *1
    Manual Transfer Planetary Carrier Washer
    *2
    Transfer Input Gear Stopper Ball
    *3
    Transfer Input Gear Stopper



36. REMOVE TRANSFER INPUT GEAR STOPPER BALL
  1. Remove the transfer input gear stopper ball.



37. REMOVE MANUAL TRANSFER PLANETARY CARRIER WASHER
  1. Remove the manual transfer planetary carrier washer.



38. REMOVE TRANSFER INPUT SHAFT


Q007437E01
  1. Remove the transfer input shaft.
    Text in Illustration 
    *1
    Transfer Low Planetary Gear Bearing
    *2
    No. 1 Transfer Thrust Bearing Race
    *3
    Transfer Input Shaft



39. REMOVE NO. 1 TRANSFER THRUST BEARING RACE
  1. Remove the No. 1 transfer thrust bearing race.



40. REMOVE TRANSFER LOW PLANETARY GEAR BEARING
  1. Remove the transfer low planetary gear bearing.



41. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING


C270034E01
  1. Remove the 2 No. 1 transfer input shaft seal rings.
    Text in Illustration 
    *1
    No. 1 Transfer Input Shaft Seal Ring



42. REMOVE TRANSFER INPUT SHAFT BEARING


F043467E02
  1. Using a snap ring expander, remove the transfer input bearing shaft snap ring.

  1. Using SST and a press, remove the transfer input shaft bearing.

    SST
    09554-30011  
    09555-55010  



43. REMOVE TRANSFER LOW PLANETARY GEAR BEARING


F043526E02
  1. Using SST, remove the transfer low planetary gear bearing.

    SST
    09612-65014   (09612-01030, 09612-01050)

    NOTICE:
    Hang SST securely to the clearance between the bearing and the low planetary gear.



44. INSPECT DRIVE SPROCKET THRUST CLEARANCE


TF00516
  1. Using a feeler gauge, measure the transfer drive sprocket sub-assembly thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.00394 to 0.00984 in.)

    Maximum clearance:
    0.25 mm (0.00984 in.)

    If the clearance exceeds the maximum, replace the transfer drive sprocket sub-assembly.



45. REMOVE TRANSFER CLUTCH HUB


D030001
  1. Using a snap ring expander, remove the transfer clutch hub shaft snap ring.

  1. Remove the transfer high and low clutch sleeve.



    TF00549
  1. Using a press, remove the transfer clutch hub.



46. REMOVE REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING


TF00518E01
  1. Using SST and a press, remove the rear transfer output shaft radial ball bearing.

    SST
    09555-55010  



47. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY


D030004E01
  1. Remove the transfer output shaft spacer and transfer output shaft spacer ball.

  1. Remove the transfer drive sprocket sub-assembly, transfer synchronizer inner ring, center ring, outer ring and front drive clutch sleeve together.

  1. Remove the transfer drive sprocket bearing.

  1. Remove the synchronizer inner ring, center ring, outer ring and front drive clutch sleeve.

  1. Remove the 3 No. 1 transfer synchromesh shifting keys and the 2 No. 1 transfer synchromesh shifting key springs.
    Text in Illustration 
    *1
    Transfer Output Shaft Spacer
    *2
    Transfer Output Shaft Spacer Ball
    *3
    Transfer Drive Sprocket Sub-assembly
    *4
    Transfer Synchronizer Inner Ring
    *5
    Transfer Synchronizer Center Ring
    *6
    Transfer Synchronizer Outer Ring
    *7
    Front Drive Clutch Sleeve
    *8
    Transfer Drive Sprocket Bearing