Home › Drivetrain ยท DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY

FRONT DRIVE SHAFT ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DRIVE SHAFT DUST COVER


F041033E01
  1. Using SST and a press, install a new dust cover.

    SST
    09527-10011  



2. INSTALL SHAFT SNAP RING


C174231
  1. Install a new snap ring.



3. INSTALL OUTBOARD JOINT BOOT


C177228E02

HINT:
Before installing the boot, wrap vinyl tape around the spline of the shaft to prevent damage to the boot.

Text in Illustration 
*1
Vinyl Tape
  1. Temporarily install a new outboard joint boot with 2 new clamps to the outboard joint shaft.

  1. Pack the outboard joint and boot with grease from the boot kit.

    Standard grease capacity:
    266 to 276 g (9.4 to 9.7 oz.)



4. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP


F052126E03
  1. Place SST to the front No. 2 axle outboard joint boot clamp.

    SST
    09521-24010  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Tighten SST so that the No. 2 front axle outboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.



    F052127E01
  1. Using SST, measure the clearance of the No. 2 front axle out board joint boot clamp.

    SST
    09240-00020  

    Standard Clearance:
    2.1 mm (0.0827 in.) or less

    CAUTION:
    If the measured value is more than the specified value, retighten the clamp.



5. INSTALL FRONT NO. 1 AXLE OUTBOARD JOINT BOOT CLAMP
  1. Hold the drive shaft lightly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Secure the outboard joint boot clamp onto the boot.



    C081563E02
  1. Place SST onto the outboard joint boot clamp.

    SST
    09521-24010  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Tighten SST so that the front axle outboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.



    C092627E01
  1. Using SST, measure the clearance of the front axle outboard joint boot clamp.

    SST
    09240-00020  

    Clearance:
    1.3 mm (0.0512 in.) or less

    NOTICE:
    If the measured value is more than the specified value, retighten the clamp.



6. INSTALL INBOARD JOINT BOOT
  1. Temporarily install a new inboard joint boot to the outboard joint shaft.



7. INSTALL FRONT AXLE INBOARD JOINT SHAFT
  1. Install new parts to the outboard joint shaft in the following order.
    1.
    Front axle inboard joint boot clamp
    2.
    Front axle inboard joint boot
    3.
    Front No. 2 axle inboard joint boot clamp

  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C067417E20
  1. Align the matchmarks and install the tripod joint onto the outboard joint shaft.

    NOTICE:
    Place the beveled side of the tripod toward the inboard joint.

    Text in Illustration 
    *a
    Beveled
    *b
    Matchmark

  1. Align the matchmarks and install the tripod to the inboard joint.

  1. Using a brass bar and hammer, tap the tripod onto the drive shaft.

    NOTICE:
    1. Do not hit the roller portion.
    2. Keep the tripod joint free of foreign matter.



    G022501
  1. Using a snap ring expander, install a new snap ring.

  1. Pack the inboard joint assembly and boot with grease from the boot kit.

    Standard Grease capacity:
    239 to 249 g (8.4 to 8.7 oz.)



    C054086E01
  1. Align the matchmarks and install the inboard joint onto the outboard joint shaft.
    Text in Illustration 
    *1
    Matchmark



8. INSTALL FRONT NO. 1 AXLE INBOARD JOINT BOOT CLAMP
  1. Hold the drive shaft lightly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Secure the inboard joint boot clamp onto the boot.



    D026925E17
  1. Place SST onto the inboard joint boot clamp.

    SST
    09521-24010  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Tighten SST so that the front axle inboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.



    D026926E01
  1. Using SST, measure the clearance of the front axle inboard joint boot clamp.

    SST
    09240-00020  

    Clearance:
    1.3 mm (0.0512 in.) or less

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.



9. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP
  1. Hold the inboard joint shaft assembly in a vise between aluminium plates.

    NOTICE:
    Do not overtighten the vise.



    C108292E14
  1. Place SST onto the No. 2 front axle inboard joint boot clamp.

    SST
    09521-24010  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Tighten SST so that the No. 2 front axle inboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.



    C086270E09
  1. Using SST, measure the clearance of the No. 2 front axle inboard joint boot clamp.

    SST
    09240-00020  

    Clearance:
    2.1 mm (0.0827 in.) or less

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.