Home › Brake › BRAKE SYSTEM (OTHER) › HYDRAULIC BRAKE BOOSTER

HYDRAULIC BRAKE BOOSTER > DISASSEMBLY

for Preparation Click here



1. REMOVE NO. 1 BRAKE ACTUATOR BRACKET


    F051421
  1. Using a 5 mm hexagon wrench, remove the bolt and No. 1 brake actuator bracket.



    F051180
  1. Using a screwdriver, remove the brake fluid level warning switch connector from the No. 1 brake actuator bracket.



2. REMOVE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY


    C172197E02
  1. Using a pin punch and hammer, remove the pin from the brake master cylinder reservoir.
    Text in Illustration 
    *1
    Pin Punch



    C172198
  1. Remove the screw and pull out the brake master cylinder reservoir sub-assembly.

  1. Remove the master cylinder reservoir filler cap.



3. REMOVE MASTER CYLINDER RESERVOIR GROMMET


    F051181E03
  1. Remove the 3 reservoir grommets from the master cylinder reservoir.



4. REMOVE NO. 1 BRAKE ACTUATOR HOSE


    F051182E02
  1. Using needle nose pliers, slide the 2 clips and remove the brake actuator hose and 2 clips.



5. REMOVE NO. 1 BRAKE ACTUATOR TUBE


    C213450
  1. Using a union nut wrench, remove the No. 1 brake actuator tube.



6. REMOVE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY


    F051185E01
  1. Using a screwdriver, remove the 2 plugs.



    F051186E02
  1. Remove the 2 screws and disconnect the wire harnesses from the master cylinder solenoid.



    F051187
  1. Using a screwdriver, remove the clip.



    C217128E01
  1. Remove the brake booster with accumulator pump assembly from the brake master cylinder.

  1. Remove the 2 brake booster pump collars and 2 brake booster pump bushes from the brake booster with accumulator pump assembly.



    F051415E03
  1. Using a 4 mm hexagon wrench, remove the 2 pins.



7. REMOVE NO. 1 BRAKE BOOSTER PUMP BRACKET


    F051189E02
  1. Using a 5 mm hexagon wrench, remove the 2 bolts and No. 1 brake booster pump bracket from the brake master cylinder solenoid.

  1. Remove the brake booster pump bush from the No. 1 brake booster pump bracket.



8. REMOVE NO. 3 BRAKE ACTUATOR BRACKET


    F051423
  1. Remove the bolt and No. 3 brake actuator bracket from the brake master cylinder.



9. REMOVE BRAKE BOOSTER ACCUMULATOR PIPE


    C217129
  1. Secure the brake booster with accumulator pump assembly in a vise.

  1. Remove the brake booster accumulator.

  1. Remove the O-ring from the brake booster accumulator.

    NOTICE:
    Make sure no foreign matter enters the pump.

  1. Remove the brake booster accumulator pipe and compression spring.



10. REMOVE MASTER CYLINDER SOLENOID


    F051195E02
  1. Remove the 6 bolts and master cylinder solenoid.



    F051196
  1. Remove the gasket.



11. REMOVE MASTER CYLINDER PUSH ROD CLEVIS


    C177091
  1. Loosen the lock nut on the rod operating adapter and remove the push rod clevis and lock nut.



    F051192E02
  1. Loosen the lock nut on the brake master cylinder side and remove the rod operating adapter and lock nut.



12. REMOVE MASTER CYLINDER BOOT


13. REMOVE BRAKE BOOSTER PISTON SUB-ASSEMBLY


    F051417E04
  1. Pressing the piston in with a screwdriver, use a pin or equivalent to push the C-ring from the hole in the master cylinder body and then remove it with another screwdriver.
    Text in Illustration 
    *1
    C-Ring
    *2
    Pin

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the plug from the piston.

  1. Remove the piston by pulling it straight out, not at an angle.

    NOTICE:
    If the piston is pulled out at an angle, there is a possibility that the cylinder bore could be damaged.