Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



TERMINALS OF ECU

C215260E03


Text in Illustration  
*a
Component without harness connected
(Skid Control ECU)
-
-

Terminal No. (Symbol)
Terminal Description
A6-1 (GND1)
Skid control ECU ground
A6-2 (+BM1)
Power supply for motor
A6-3 (FR+)
Front speed sensor RH power supply output
A6-4 (FL-)
Front speed sensor LH input
A6-5 (RR+)
Rear speed sensor RH power supply output
A6-6 (RL-)
Rear speed sensor LH input
A6-7 (STP)
Stop light switch assembly
A6-9 (CSW)
VSC OFF switch
A6-11 (CANH)
CAN communication terminal H
A6-12 (SP1)
Speedometer signal
A6-13 (ATRC)*2
A-TRAC switch
A6-16 (STPO)
Stop light switch assembly
A6-17 (FR-)
Front speed sensor RH input
A6-18 (FL+)
Front speed sensor LH power supply output
A6-19 (RR-)
Rear speed sensor RH input
A6-20 (RL+)
Rear speed sensor LH power supply output
A6-24 (TS)
Sensor test terminal (Signal check switch)
A6-25 (CANL)
CAN communication terminal L
A6-27 (EXI)*2
for Part-time 4WD: A.D.D. detection switch
for Full-time 4WD: Center differential lock detection switch
A6-31 (+BS)
Power supply for solenoid
A6-32 (GND2)
Skid control ECU ground
A6-40 (EXI3)
w/ Rear Differential Lock: Rear differential lock detection switch
w/o Rear Differential Lock*1: IG power supply
w/o Rear Differential Lock*2: Front wheel drive ECU
A6-41 (LBL)
Brake fluid level warning switch
A6-44 (HDCS)*3
Downhill assist control switch
A6-45 (STP2)
Stop light switch assembly
A6-46 (IG1)
IG1 power supply
A7-1 (IG2)
IG2 power supply
A7-2 (+BM2)
Power supply for motor
A7-4 (GND3)
Skid control ECU ground
  1. *1: for 2WD
  2. *2: for 4WD
  3. *3: w/ Downhill Assist Control

TERMINAL INSPECTION


  1. Disconnect the connector and measure the voltage or resistance on the wire harness side.

    HINT:
    The voltage cannot be measured with the connector connected to the skid control ECU as the connector is watertight.


    C173112E03


    Text in Illustration  
    *a
    Front view of wire harness connector
    (to Skid Control ECU)
    -
    -

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A6-1 (GND1) - Body ground
    W-B
    Ground
    Always
    Below 1 Ω
    A6-2 (+BM1) - Body ground
    B
    Power supply for motor
    (from battery)
    Always
    11 to 14 V
    A6-7 (STP) - Body ground
    L
    Stop light switch assembly
    Brake pedal depressed → released
    8 to 14 V → Below 1.5 V
    A6-9 (CSW) - Body ground
    V-W
    VSC OFF switch input
    VSC OFF switch off → on and held
    10 kΩ or higher → Below 1 Ω
    A6-13 (ATRC) - Body ground*1
    LG
    A-TRAC switch input
    A-TRAC switch off → on and held
    10 kΩ or higher → Below 1 Ω
    A6-16 (STPO) - Body ground
    LG-B
    Stop light switch assembly
    Ignition switch off → ON
    Below 1.1 V → 11 to 14 V
    A6-31 (+BS) - Body ground
    L-R
    Power supply for solenoid
    (from battery)
    Always
    11 to 14 V
    A6-32 (GND2) - Body ground
    W-B
    Ground
    Always
    Below 1 Ω
    A6-41 (LBL) - Body ground
    V-G
    Brake fluid level warning switch
    Brake fluid level +/-5 mm (+/-0.197 in.) from minimum level → maximum level
    Below 1 Ω → 1.9 to 2.1 kΩ
    A6-44 (HDCS) - Body ground*2
    P
    Downhill assist control switch input
    Downhill assist control switch off → on
    10 kΩ or higher → Below 1 Ω
    A6-45 (STP2) - Body ground
    V-G
    Stop light switch assembly
    Brake pedal depressed → released
    8 to 14 V → Below 1.5 V
    A6-46 (IG1) - Body ground
    G
    IG1 power supply
    Ignition switch off → ON
    Below 1 V → 11 to 14 V
    A7-1 (IG2) - Body ground
    W
    IG2 power supply
    Ignition switch off → ON
    Below 1 V → 11 to 14 V
    A7-2 (+BM2) - Body ground
    B
    Power supply for motor
    (from battery)
    Always
    11 to 14 V
    A7-4 (GND3) - Body ground
    W-B
    Ground
    Always
    Below 1 Ω
    1. *1: for 4WD
    2. *2: w/ Downhill Assist Control