Home › Vehicle Interior › SEAT BELT › REAR NO. 1 SEAT OUTER BELT ASSEMBLY

REAR NO. 1 SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


B241718E01
  1. Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the bolt as shown in the illustration.

    HINT:
    First install bolt A, and then install bolt B.

    Torque:
    for bolt A:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
    for bolt B:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the rear No. 1 seat outer belt shoulder anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL REAR NO. 2 SEATBACK LOCK STRIKER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat)
  1. Install the seatback lock striker (Click here).



3. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY LH
  1. Pass the rear No. 1 seat outer belt floor anchor through the rear window side garnish assembly LH and attach the 4 claws and 2 guides.

  1. Attach the 7 clips and 4 guides to install the rear window side garnish assembly LH.



4. INSTALL REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH
  1. w/ Rear No. 2 Seat:

    1. Pass the rear No. 2 seat outer belt floor anchor through the rear No. 2 window side garnish assembly LH and attach the 7 claws and guide.

  1. Attach the 6 clips and guide to install the rear No. 2 window side garnish assembly LH.



5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. w/o Rear No. 2 Seat:

    1. Pass the rear seatback lock control lever base through the deck trim side panel.

    2. Attach the 4 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.

    3. Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.

    4. Install the 3 bolts and 2 screws.

    5. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }



  1. w/ Rear No. 2 Seat:

    1. Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.

    2. Install the 3 bolts and 2 screws.

    3. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    4. B242825E01
    5. for LH Side:
      Install the rear No. 2 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the anchor plate sub-assembly to overlap the protruding parts of the vehicle body.

      Text in Illustration 
      *a
      Protruding Part



    6. B242824E01
    7. for RH Side:
      Install the rear No. 2 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the anchor plate sub-assembly to overlap the protruding parts of the vehicle body.

      Text in Illustration 
      *a
      Protruding Part



6. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER
  1. Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.

  1. Attach the 2 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



7. INSTALL FRONT DECK SIDE TRIM COVER LH
  1. Attach the 2 claws to install the front deck side trim cover LH.



8. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
  1. Push in the No. 1 luggage compartment trim hook to install it.

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim hook.



9. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
  1. Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.

    HINT:
    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.



10. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)
  1. Attach the 4 claws to install the rear floor carpet assembly.



11. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
  1. Attach the 5 clips to install the rear floor mat rear support plate.



12. INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)
  1. Install the inner floor side rail sub-assembly with the 4 bolts.



13. INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)
  1. Attach the 2 guides to install the deck board assembly.

  1. Install the 6 bolts.



14. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)
  1. Attach the 4 clips and 2 guides to install the luggage compartment side cover sub-assembly LH.



15. INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

HINT:
Use the same procedure as for the LH side.



16. INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)
  1. Attach the 3 clips to install the rear No. 2 floor board assembly.



17. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)
  1. Attach the 2 clips and 2 guides to install the No. 2 deck board sub-assembly.



18. INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board, w/o Rear No. 2 Seat)
  1. Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.

  1. Attach the 2 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 2 luggage compartment trim cover.



19. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)
  1. Attach the clip to install the No. 1 deck board sub-assembly.



20. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)
  1. Install the luggage hold belt striker and No. 1 luggage compartment trim cover with the bolt.

  1. Attach the 4 claws to close the cover.

    HINT:
    Use the same procedure for the other No. 1 luggage compartment trim cover.



21. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B240010E01
  1. Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle to install the rear door opening trim weatherstrip LH as shown in the illustration.
    Text in Illustration 
    *1
    Paint Mark
    *2
    Mark Position



22. INSTALL REAR DOOR SCUFF PLATE LH
  1. Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate LH.



23. INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)