REAR NO. 1 SEAT OUTER BELT ASSEMBLY > REMOVAL |
| 1. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat) |
![]() |
Using a screwdriver, detach the 2 claws to remove the rear No. 1 floor step cover.
| *1 | Protective Tape |
| 2. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat) |
![]() |
Remove the 2 bolts and quarter scuff plate LH.
| 3. REMOVE REAR DOOR SCUFF PLATE LH |
Put protective tape around the rear door scuff plate LH.
![]() |
Using a screwdriver, detach the 3 clips, 6 claws and 2 guides to remove the rear door scuff plate LH.
| *1 | Protective Tape |
| 4. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Remove the rear door opening trim weatherstrip LH.
| 5. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board) |
![]() |
Detach the 4 claws to open the cover.
![]() |
Remove the bolt, luggage hold belt striker and No. 1 luggage compartment trim cover.
| *1 | Luggage Hold Belt Striker |
| 6. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board) |
![]() |
Detach the clip to remove the No. 1 deck board sub-assembly.
| 7. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board, w/o Rear No. 2 Seat) |
![]() |
Detach the 2 claws to open the cover.
![]() |
Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.
| *1 | Luggage Hold Belt Striker |
| 8. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
![]() |
Detach the 2 clips and 2 guides to remove the No. 2 deck board sub-assembly.
| 9. REMOVE REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board) |
![]() |
Detach the 3 clips to remove the rear No. 2 floor board assembly.
| 10. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board) |
![]() |
Using a screwdriver, detach the 4 clips and 2 guides to remove the luggage compartment side cover sub-assembly LH.
| *1 | Protective Tape |
| 11. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board) |
| 12. REMOVE DECK BOARD ASSEMBLY (w/ Deck Board) |
![]() |
Remove the 6 bolts.
Detach the 2 guides to remove the deck board assembly.
| 13. REMOVE INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board) |
![]() |
Remove the 4 bolts and inner floor side rail sub-assembly.
| 14. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE |
![]() |
Detach the 5 clips to remove the rear floor mat rear support plate.
| 15. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) |
![]() |
Detach the 5 clips to remove the rear floor mat rear support plate.
| 16. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER |
![]() |
Detach the 3 claws to remove the rear No. 1 seat outer lap belt anchor cover.
| 17. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
![]() |
Remove the No. 1 luggage compartment trim hook by turning it clockwise.
| 18. REMOVE FRONT DECK SIDE TRIM COVER LH |
![]() |
Using a screwdriver, detach the 2 claws to remove the front deck side trim cover LH.
| *1 | Protective Tape |
| 19. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM COVER |
![]() |
Detach the 2 claws to open the cover.
![]() |
Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.
| *1 | Luggage Hold Belt Striker |
| 20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
![]() |
w/o Rear No. 2 Seat:
Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
Remove the 3 bolts and 2 screws.
Detach the 7 clips, 5 claws and 2 guides and remove the deck trim side panel.

![]() |
Detach the 4 claws and 2 guides, pass the rear seatback lock control lever base through the deck trim side panel, and remove the deck trim side panel.
w/ Rear No. 2 Seat:
![]() |
Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
![]() |
Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.
![]() |
for RH Side:
Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.
Remove the 3 bolts and 2 screws.
Detach the 7 clips, 5 claws and 2 guides.

| 21. REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH |
![]() |
w/o Rear No. 2 Seat:
Detach the 6 clips and guide to remove the rear No. 2 window side garnish assembly LH.
![]() |
w/ Rear No. 2 Seat:
Detach the 6 clips and guide.
![]() |
Detach the 7 claws and guide and pass the rear No. 2 seat outer belt floor anchor through the rear No. 2 window side garnish assembly LH to remove the rear No. 2 window side garnish assembly LH.
| 22. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY LH |
![]() |
Detach the 7 clips and 4 guides.
![]() |
Detach the 4 claws and 2 guides and pass the rear No. 1 seat outer belt floor anchor through the rear window side garnish assembly LH to remove the rear window side garnish assembly LH.
| 23. REMOVE REAR NO. 2 SEATBACK LOCK STRIKER SUB-ASSEMBLY LH (w/o Rear No. 2 Seat) |
![]() |
Remove the 2 bolts.
Detach the claw and remove the striker.
| 24. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and rear No. 1 seat outer belt shoulder anchor.
![]() |
Remove the 2 bolts and rear No. 1 seat outer belt assembly.