KINETIC DYNAMIC SUSPENSION SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn ON the Techstream.
Enter the following menus: Chassis / KDSS / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Oil Pressure Sensor | Oil pressure sensor/ Min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi) Max.: 784.76 MPa (8002.35 kgf/cm2, 113790.20 psi) | 2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi): When vehicle stopped and fluid temperature 20°C (68°F) | - |
| Acceleration Sensor | Lateral G/ Min.: -1176.37 m/s2 Max.: -1176.33 m/s2 | - | Changes in proportion with acceleration during turning. |
| Stop Light Switch | Stop light switch/ ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| TC Terminal | TC terminal/ ON or OFF | OFF | - |
| TS Terminal | TS terminal/ ON or OFF | OFF | - |
| FR Wheel Speed | Front wheel RH speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front wheel LH speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| RR Wheel Speed | Rear wheel RH speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear wheel LH speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| IG Power Source Voltage | IG power source voltage/ Min.: 0.0 V Max.: 25.5 V | Ignition switch ON: 11 to 14 V | - |
| Steering Angle | Steering angle/ Min.: -49152.0 deg Max.: 49150.5 deg | - | Changes in proportion with the amount of steering wheel rotation during steering operation. |
| Compatible Constant Information | Compatible constant information/ Min.: 0 Max.: 255 | - | - |
| Design Constant Information | Design constant information/ Min.: 0 Max.: 255 | - | - |
| Accumulator Valve (Downside) | Stabilizer control solenoid valve (for Upper Chamber)/ ON or OFF | ON: Stabilizer control solenoid valve closed OFF: Stabilizer control solenoid valve open | - |
| Accumulator Valve (Upside) | Stabilizer control solenoid valve (for Lower Chamber)/ ON or OFF | ON: Stabilizer control solenoid valve open OFF: Stabilizer control solenoid valve closed | - |
| Number of Trouble Codes | Number of trouble codes/ Min.: 0 Max.: 255 | 0 | - |
| ACTIVE TEST |
Warm up the engine.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn ON the Techstream.
Enter the following menus: Chassis / KDSS / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Accumulator Valve (Upside) | Stabilizer control solenoid valve (for Upper Chamber) | Valve ON / OFF | The operating sound of the solenoid (clicking sound) can be heard. ON: Data List ON OFF: Data List OFF When the Active Test is performed, the solenoid turns on for 3 seconds. |
| Accumulator Valve (Downside) | Stabilizer control solenoid valve (for Lower Chamber) | Valve ON / OFF | The operating sound of the solenoid (clicking sound) can be heard. ON: Data List ON OFF: Data List OFF When the Active Test is performed, the solenoid turns on for 3 seconds. |