Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL

BRAKE PEDAL > ADJUSTMENT

for Preparation Click here



1. CHECK BRAKE PEDAL HEIGHT


    C253410E01
  1. Check the brake pedal height.

    Pedal height from Floor panel:
    158.8 to 168.8 mm (6.25 to 6.46 in.)

    Text in Illustration 
    *1
    Rod Operating Adapter
    *2
    Stop Light Switch Assembly
    *3
    Floor Panel
    *a
    Pedal Height

    NOTICE:
    Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.

    If the pedal height is incorrect, adjust the rod operating adapter length.



    C253411E01
  1. Adjust the rod operating adapter length.

    1. Remove the clip and clevis pin.

    2. Loosen the clevis lock nut.
      Text in Illustration 
      *1
      Clevis Lock Nut

    3. Adjust the rod operating adapter length by turning the pedal push rod clevis.

      Rod operating adapter length "A":
      236.3 to 237.3 mm (9.30 to 9.34 in.)

    4. Tighten the clevis lock nut.

      Torque:
      26 N*m{ 260 kgf*cm , 19 ft.*lbf }

    5. Install the clip and clevis pin.
      If the pedal height is incorrect even if the rod operating adapter is adjusted, check that there is no damage to the brake pedal, brake pedal lever, brake pedal bracket or floor panel.

      1. Even if there is damage, there is no problem if the reserve distance is within the standard value.
      2. If necessary, replace the clip.



2. CHECK AND ADJUST STOP LIGHT SWITCH ASSEMBLY

HINT:
If the pedal height is incorrect, check and adjust the stop light switch clearance.

  1. Disconnect the stop light switch assembly connector from the stop light switch assembly.

  1. Turn the stop light switch assembly counterclockwise and remove the stop light switch assembly.



    C172890E03
  1. Insert the stop light switch assembly until the body hits the cushion.
    Text in Illustration 
    *1
    Stop Light Switch

    NOTICE:
    When inserting the stop light switch assembly, support the pedal from behind so that the pedal is not pushed in.

  1. Make a quarter turn clockwise to install the stop light switch assembly.

    NOTICE:
    The turning torque for installing the stop light switch should be 1.5 N*m (15 kgf*cm, 13 in.*lbf) or less.

    HINT:
    Due to the inverse screw structure, if the stop light switch assembly is turned clockwise, the stop light switch assembly moves in the direction to be pulled out.

  1. Connect the stop light switch connector to the stop light switch assembly.

  1. Check the protrusion of the rod.

    Protrusion of the rod:
    1.5 to 2.5 mm (0.0591 to 0.0984 in.)

  1. Install the clevis pin and clip.

  1. After adjusting the pedal height, check the pedal free play.



3. CHECK PEDAL FREE PLAY


    C253412E01
  1. Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.
    Text in Illustration 
    *a
    Pedal Free Play

  1. Push in the pedal until the resistance is felt. Measure the distance.

    Pedal free play:
    1 to 6 mm (0.0394 to 0.236 in.)

    HINT:
    Check the brake pedal free play at the same location as that used when checking the brake pedal height.



4. CHECK PEDAL RESERVE DISTANCE


    R000934E27
  1. Release the parking brake pedal.
    With the engine running, depress the pedal and measure the pedal reserve distance.
    Text in Illustration 
    *a
    Pedal Reserve Distance

    Pedal reserve distance from floor panel at 490 N (50 kgf, 110.2 lbf):
    More than 92 mm (3.62 in.)

    If incorrect, troubleshoot the brake system.

    HINT:
    Insert a ruler into the slit to measure the pedal reserve distance.