STEERING LOCK SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Turn the engine switch off.
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / (desired system) / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | Engine switch status/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| #Codes | Number of diagnostic trouble codes/0 to 255 | - | - |
| Steering Lock Sleep Cond | Steering lock ECU sleep mode possible/Yes or No | Yes: Sleep mode possible No: Sleep mode not possible | - |
| Steering Lock Start Cond | Steering lock ECU wake up signal sent/Yes or No | Yes: Wake up signal sent No: Wake up signal not sent | - |
| Engine Start Condition | Engine start status/OK or NG | NG: Engine start not possible OK: Engine start possible | - |
| Sensor Value | Sensor malfunction record/NG (PAST) or OK | NG (PAST): Sensor malfunction OK: No malfunction | - |
| Power Supply Short | Short in ECU record/NG (PAST) or OK | NG (PAST): Short in ECU OK: No malfunction | - |
| Power Supply Open | Open in ECU record/NG (PAST) or OK | NG (PAST): Open in ECU OK: No malfunction | - |
| Motor Driver Short | Short in driver ECU record/NG (PAST) or OK | NG (PAST): Short in driver ECU OK: No malfunction | If NG (PAST) is displayed, proceed to troubleshooting for DTC B2782. |
| Motor Driver Open | Open in driver ECU record/NG (PAST) or OK | NG (PAST): Open in driver ECU OK: No malfunction | If NG (PAST) is displayed, proceed to troubleshooting for DTC B2782. |
| Lock/Unlock Receive | Steering lock command reception record/YES or NO | YES: Steering lock/unlock signal received NO: Steering lock/unlock signal not received | - |
| Lock Bar Stuck Error | Lock bar stuck malfunction record/NG (PAST) or OK | NG (PAST): Lock bar stuck malfunction OK: No malfunction | - |
| Push Start Error | Push button start function malfunction/NG (PAST) or OK | NG (PAST): Malfunction in push button start OK: No malfunction | - |
| IG2 Status | IG2 voltage status/ON or OFF | ON: 11 to 14 V OFF: Below 1 V | - |
| IG(Lin) | IG signal via LIN communication/ON or OFF | ON: IG signal sent via LIN communication OFF: IG signal not sent via LIN communication | - |
| S Code Check | S code certification result/NG or OK | NG: S code certification result abnormal OK: S code certification result normal | - |
| L Code Check | L code certification result/NG or OK | NG: L code certification result abnormal OK: L code certification result normal | - |
| Unlock Request Receive | Steering lock unlock command reception status/NG or OK | NG: Unlock request not received OK: Unlock request received | - |
| Lock Request Receive | Steering lock lock command reception status/NG or OK | NG: Lock request not received OK: Lock request received | - |
| S Code Check(Past) | S code certification result/NG (PAST) or OK | NG (PAST): S code certification result abnormal OK: S code certification result normal | - |
| L Code Check(Past) | L code certification result/NG (PAST) or OK | NG (PAST): L code certification result abnormal OK: L code certification result normal | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FL Door Courtesy | Front door courtesy switch LH/ON or OFF | ON: Front door courtesy switch LH on OFF: Front door courtesy switch LH off | - |
| PERFORM ACTIVE TEST |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Power Source Control / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| P Supply for Steering Lock | Power management control ECU | Supply or Stop | This test supplies or stops power to the steering lock motor. |