ENGINE IMMOBILISER SYSTEM (w/o Smart Key System) > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Immobiliser / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door Courtesy SW | Driver side door courtesy light switch / ON or OFF | ON: Driver side door open OFF: Driver side door closed | - |
| Key SW | Unlock warning switch signal / ON or OFF | ON: Key inserted in ignition key cylinder OFF: No key in ignition key cylinder | - |
| IG SW | Ignition switch signal / ON or OFF | ON: Ignition switch ON OFF: Ignition switch ACC or off | - |
| Immobiliser | Immobiliser system status / Set or Unset | Set: No key in ignition key cylinder Unset: Key inserted in ignition key cylinder | - |
| Response | Transponder chip data / OK or NG | OK: Data OK NG: Data error | - |
| Frame Error | Transponder chip data / OK or NG | OK: Data OK NG: Data error | - |
| Different Serial Number | Transponder chip data / OK or NG | OK: Data OK NG: Data error | - |
| Different Encrypt Code | Transponder chip data / OK or NG | OK: Data OK NG: Data error | - |
| Abnormal Status | Transponder chip data / OK or NG | OK: Data OK NG: Data error | - |
| BCC Malfunction | Transponder chip signal / OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Sub Key | Sub-key code signal / Reg or Unreg | Reg: Registered sub-key code sent Unreg: Unmatching sub-key code sent | - |
| Master Key | Master key code signal / Reg or Unreg | Reg: Registered master key code sent Unreg: Unmatching master key code sent | - |
| Transponder S-code | Number of registered sub-keys / min.: 0, max.: 3 | Number of registered sub-keys | - |
| Transponder M-code | Number of registered master keys / min.: 0, max.: 5 | Number of registered master keys | - |
| Reg Code Space Full | Key registration code memory space full / Yes or No | No: Possible to register more key codes Yes: Cannot register any more key codes | - |
| +B | +B judgment / Normal or Break | Normal: Battery power supply normal Break: Battery power supply malfunctioning | - |
| Antenna Coil Status | Antenna coil condition / Normal or Fail | Normal: Antenna coil normal Fail: Antenna coil malfunctioning | - |
| EEPROM Status | EEPROM status / OK or NG | OK: Data OK NG: Data error | - |
| E/G Start Permission | Engine start permission / OK or NG | OK: Engine start permitted NG: Engine start not permitted | - |
| Immobi ECU Comm Spd | Immobiliser ECU communication speed / Unknown, 50bps, 200bps or No Res | Unknown: ECU communication speed unknown 50bps: ECU communication speed 50 bps 200bps: ECU communication speed 200 bps No Res: ECU communication speed no response | - |
| The Number of DTCs | Number of DTCs / Min.: 0, Max.: 255 | Number of stored DTCs | - |
| PERFORM ACTIVE TEST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Immobiliser / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Security Indicator | Security indicator light | ON/OFF | The test is possible when the following conditions are met:
|