Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type)

REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type) > Display Signal Circuit between Navigation Receiver Assembly and Television Camera Assembly

for Preparation Click here


DESCRIPTION

This is the display signal circuit between the navigation receiver assembly and the television camera assembly.

WIRING DIAGRAM


E282894E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the G38 navigation receiver assembly connector.

  1. Disconnect the Y2 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G38-11 (CA+) - Y2-6 (CB+)
    Always
    Below 1 Ω
    G38-12 (V+) - Y2-3 (CV+)
    Always
    Below 1 Ω
    G38-23 (CGND) - Y2-5 (CGND)
    Always
    Below 1 Ω
    G38-24 (V-) - Y2-2 (CV-)
    Always
    Below 1 Ω
    G38-11 (CA+) - Body ground
    Always
    10 kΩ or higher
    G38-12 (V+) - Body ground
    Always
    10 kΩ or higher
    G38-23 (CGND) - Body ground
    Always
    10 kΩ or higher
    G38-24 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK NAVIGATION RECEIVER ASSEMBLY
E225824E47
  1. Reconnect the G38 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G38-23 (CGND) - Body ground
    Always
    Below 1 Ω
    G38-24 (V-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G38-11 (CA+) - G38-23 (CGND)
    Ignition switch ON
    Shift lever in R
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


3.CHECK REAR TELEVISION CAMERA ASSEMBLY
  1. Reconnect the Y2 rear television camera assembly connector.



  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


    E282882E01


    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)
    *b
    Waveform 1 (under normal conditions)
    *c
    Waveform 2 (camera lens is covered, blacking out the screen)
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    G38-12 (V+) - G38-24 (V-)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)