ENGINE UNIT > INSPECTION |
| 1. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.
| *a | Measurement Length |
![]() |
Using a vernier caliper, measure the diameter of the elongated thread at the narrowest visible area.
| 2. INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
Turn the roller by hand to check that it turns smoothly.
If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.
| 3. INSPECT VALVE LASH ADJUSTER ASSEMBLY |
Place the valve lash adjuster assembly into a container filled with engine oil.
![]() |
Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.
| *1 | Tapered Path |
| *2 | Plunger |
| *3 | Low Pressure Chamber |
| *4 | Check Ball |
| *5 | High Pressure Chamber |
| *a | CORRECT |
| *b | INCORRECT |
Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed the air.
After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.
| 4. INSPECT CAMSHAFT |
Inspect the camshaft runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
Using a micrometer, measure the cam lobe height.
| Item | Specified Condition |
| Intake camshaft | 43.890 to 43.990 mm (1.728 to 1.732 in.) |
| Exhaust camshaft | 44.262 to 44.362 mm (1.743 to 1.747 in.) |
| Item | Specified Condition |
| Intake camshaft | 43.840 mm (1.726 in.) |
| Exhaust camshaft | 44.212 mm (1.741 in.) |
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
| No. 1 journal | 35.946 to 35.960 mm (1.4152 to 1.4157 in.) |
| Other journals | 25.959 to 25.975 mm (1.0221 to 1.0226 in.) |
| 5. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Fix the camshaft in place.
![]() |
Put the camshaft timing gear assembly and camshaft together by aligning the pin hole and straight pin.
| *1 | Pin Hole |
| *2 | Straight Pin |
Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.
Check that there is no clearance between the camshaft timing gear assembly flange and camshaft.
![]() |
Tighten the flange bolt while holding the camshaft.
Check the lock of the camshaft timing gear assembly.
Fix the camshaft in place and confirm that the camshaft timing gear assembly is locked.
![]() |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
| *1 | Advance Side Path |
| *2 | Retard Side Path |
| *3 | Open |
| *4 | Close |
![]() | Rubber |
![]() | Vinyl Tape |
Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path, as shown in the illustration.
![]() |
Apply air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths.
| *1 | Advance Side Path |
| *2 | Retard Side Path |
![]() |
Check that the camshaft timing gear assembly rotates in the advance direction when reducing the air pressure applied to the retard side path.
| *1 | Advance Side Path |
| *2 | Retard Side Path |
| *3 | Hold Pressure |
| *4 | Decompress |
When the camshaft timing gear assembly reaches the most advanced position, release the air pressure first from the retard side path and next from the advance side path.
Check for smooth rotation.
Turn the camshaft timing gear assembly within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.
Check the lock in the most retarded position.
Confirm that the camshaft timing gear assembly locks at the most retarded position.
![]() |
Remove the flange bolt and camshaft timing gear assembly.
| *1 | Do not remove |
| *2 | Straight Pin |
| *3 | Flange Bolt |
| 6. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Fix the camshaft in place.
![]() |
Put the camshaft timing exhaust gear assembly and camshaft together by aligning the pin hole and straight pin.
| *1 | Pin Hole |
| *2 | Straight Pin |
Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.
Check that there is no clearance between the gear flange and camshaft.
![]() |
Tighten the flange bolt while holding the camshaft.
Check the camshaft timing exhaust gear lock.
Make sure that the camshaft timing exhaust gear assembly locks.
![]() |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
| *1 | Advance Side Path |
| *2 | Retard Side Path |
| *3 | Open |
| *4 | Close |
![]() | Rubber |
![]() | Vinyl Tape |
Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path, as shown in the illustration.
![]() |
Apply air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths (the advance side path and retard side path).
| *1 | Advance Side Path |
| *2 | Retard Side Path |
![]() |
Make sure that the camshaft timing exhaust gear assembly rotates in the retard direction when reducing the air pressure applied to the advance side path.
| *1 | Advance Side Path |
| *2 | Retard Side Path |
| *3 | Hold Pressure |
| *4 | Decompress |
When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure first from the advance side path, and then release the air pressure from the retard side path.
Check for smooth rotation.
Turn the camshaft timing exhaust gear assembly within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear assembly turns smoothly.
Check the lock at the most advanced position.
Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.
![]() |
Remove the flange bolt and camshaft timing exhaust gear assembly.
| *1 | Do not remove |
| *2 | Straight Pin |
| *3 | Flange Bolt |
| 7. INSPECT NO. 1 CHAIN SUB-ASSEMBLY |
![]() |
Using a spring scale, pull the No. 1 chain with a force of 147 N (15 kgf, 33 lbf) and measure the length of the No. 1 chain using a vernier caliper.
| *a | Measurement Area |
| 8. INSPECT NO. 2 CHAIN SUB-ASSEMBLY |
Using a spring scale, pull the No. 2 chain with a force of 147 N (15 kgf, 33 lbf) and measure the length of the No. 2 chain using a vernier caliper.
| 9. INSPECT CRANKSHAFT TIMING SPROCKET |
![]() |
Wrap the No. 1 chain around the sprocket.
Using a vernier caliper, measure the crankshaft timing sprocket diameter with the No. 1 chain.
| 10. INSPECT NO. 1 IDLE GEAR |
![]() |
Wrap the No. 1 chain around the gear.
Using a vernier caliper, measure the No. 1 idle gear diameter with the No. 1 chain.
| 11. INSPECT NO. 1 IDLE GEAR SHAFT OIL CLEARANCE |
Using a micrometer, measure the No. 1 idle gear shaft diameter.
Using a caliper gauge, measure the inside diameter of the idle gear.
Subtract the idle gear shaft diameter measurement from the idle gear inside diameter measurement.
| 12. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.
| *1 | Plunger |
| *2 | Stopper Plate |
| *a | Moves Smoothly |
| 13. INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly.
| *a | Depth |
| *b | Moves Smoothly |
Measure the depth of wear of the chain tensioner.
| 14. INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly.
| *a | Depth |
| *b | Moves Smoothly |
Measure the depth of wear of the chain tensioner.
| 15. INSPECT CHAIN TENSIONER SLIPPER |
![]() |
Measure the depth of wear of the chain tensioner slipper.
| *a | Depth |
| 16. INSPECT NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Measure the depth of wear of the No. 1 chain vibration damper.
| *a | Depth |
| 17. INSPECT NO. 2 CHAIN VIBRATION DAMPER |
![]() |
Measure the depth of wear of the No. 2 chain vibration damper.
| *a | Depth |
| 18. INSPECT CAMSHAFT THRUST CLEARANCE |
![]() |
Install the camshafts .
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| 19. INSPECT CAMSHAFT OIL CLEARANCE |
Clean the camshaft bearing caps, camshaft housing and camshaft journals.
Place the camshafts on the camshaft housing.
![]() |
Lay a strip of Plastigage across each camshaft journal.
| *1 | Plastigage |
Install the camshaft bearing caps .
Remove the camshaft bearing caps .
![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| No. 1 journal | 0.032 to 0.063 mm (0.00126 to 0.00248 in.) |
| Other journals | 0.025 to 0.062 mm (0.000984 to 0.00244 in.) |
| Item | Specified Condition |
| No. 1 journal | 0.10 mm (0.00394 in.) |
| Other journals | 0.09 mm (0.00354 in.) |
| *1 | Plastigage |
| *2 | No. 1 Journal |
| *3 | Other Journals |
| 20. INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head.
| 21. INSPECT INTAKE MANIFOLD FOR FLATNESS |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the surfaces which contact the cylinder head and intake air surge tank.
| Item | Specified Condition |
| Intake air surge tank side | 0.80 mm (0.0315 in.) |
| Cylinder head side | 0.20 mm (0.00787 in.) |
| *A | Intake Air Surge Tank Side |
| *B | Cylinder Head Side |