ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY |
![]() |
Using a 24 mm deep socket wrench, remove the oil pressure switch.
| 2. REMOVE ENGINE COOLANT TEMPERATURE SENSOR |
![]() |
Using a 19 mm deep socket wrench, remove the sensor.
Remove the gasket from the sensor.
| 3. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
![]() |
Remove the water drain cock plug from the water drain cock.
| *a | RH side |
Remove the water drain cock from the cylinder block.
| 4. REMOVE VVT SENSOR |
![]() |
LH:
Remove the 2 bolts and 2 VVT sensors.
![]() |
RH:
Remove the 2 bolts and 2 VVT sensors.
| 5. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Remove the bolt and crankshaft position sensor.
| 6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH |
![]() |
LH:
Remove the 2 bolts and 2 oil control valves.
![]() |
RH:
Remove the 2 bolts and 2 oil control valves.
| 7. REMOVE OIL FILLER CAP HOUSING |
![]() |
Remove the oil filler cap.
Remove the 2 nuts, oil filler cap housing and gasket.
| 8. REMOVE NO. 1 OIL PIPE |
![]() |
Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.
| 9. REMOVE NO. 2 OIL PIPE |
![]() |
Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.
| 10. REMOVE OIL FILTER ELEMENT |
![]() |
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
| *1 | Pipe |
| *2 | Hose |
![]() |
Remove the oil filter drain plug.
![]() |
Install the pipe to the oil filter cap.
| *1 | Oil Filter Cap Assembly |
| *2 | Valve |
| *3 | Pipe |
| *4 | O-ring |
| *5 | Hose |
![]() |
Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.
![]() |
Using SST, remove the oil filter cap.
| *1 | Oil Filter Bracket Clip |
![]() |
Remove the oil filter element and O-ring from the oil filter cap.
| *1 | O-ring |
| 11. REMOVE OIL FILTER BRACKET |
![]() |
Remove the 2 nuts, bolt, oil filter bracket and gasket.
| 12. REMOVE WATER INLET HOUSING |
![]() |
Disconnect the 3 water by-pass hoses.
![]() |
Remove the 5 bolts and water inlet housing.
![]() |
Remove the O-ring and gasket from the water outlet pipe and water pump assembly.
![]() |
Remove the 3 water by-pass hoses.
| 13. REMOVE REAR WATER BY-PASS JOINT |
![]() |
Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.
Remove the O-ring from the No. 1 water outlet pipe.
| 14. REMOVE SPARK PLUG |
Remove the 6 spark plugs.
| 15. REMOVE PCV VALVE SUB-ASSEMBLY |
![]() |
Remove the PCV valve hose.
Remove the PCV valve.
| 16. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, hold the crankshaft pulley and loosen the pulley bolt. Continue to loosen the bolt until only 2 or 3 threads are screwed into the crankshaft.
![]() |
Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt.
| 17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH |
![]() |
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
![]() |
Remove the 3 gaskets.
| 18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
![]() |
Remove the 3 gaskets.
| 19. REMOVE SPARK PLUG TUBE GASKET |
![]() |
Bend the ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.
![]() | Pry |
Remove the 6 spark plug tube gaskets.
| 20. REMOVE OIL PAN DRAIN PLUG |
Remove the drain plug and gasket.
| 21. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 10 bolts and 2 nuts.
![]() |
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
| *1 | Oil Pan Seal Cutter |
| 22. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the 2 nuts, oil strainer sub-assembly and gasket.
| 23. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 17 bolts and 2 nuts.
![]() |
Using a screwdriver, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block as shown in the illustration.
| *1 | LH Side |
| *2 | RH Side |
| *a | Pry |
![]() |
Remove the 3 O-rings from the timing chain cover sub-assembly.
| 24. REMOVE NO. 1 OIL PAN BAFFLE PLATE |
![]() |
Remove the 6 bolts and No. 1 oil pan baffle plate.
| 25. REMOVE ENGINE REAR OIL SEAL RETAINER |
![]() |
Remove the 5 bolts and 2 nuts.
Using a screwdriver, remove the engine rear oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.
| *a | Pry |
| 26. REMOVE REAR CRANKSHAFT OIL SEAL |
![]() |
Using a screwdriver and hammer, tap out the rear crankshaft oil seal.
| 27. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 26 bolts and the 2 nuts.
![]() |
Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head or cylinder block with a screwdriver.
![]() |
Remove the oil pump gasket from the cylinder block.
| 28. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 8 bolts, water pump and gasket.
| 29. REMOVE FRONT CRANKSHAFT OIL SEAL |
Using a screwdriver and wooden block, pry out the front crankshaft oil seal.
| 30. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
Temporarily install the pulley set bolt.
![]() |
Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
| *1 | Center Line |
| *2 | Timing Mark |
| *3 | Sensor Plate |
![]() |
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
| *1 | Timing Mark |
| 31. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
| *1 | Plunger |
| *2 | Stopper Plate |
| *3 | Pin |
Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm (0.0500 in.) into the stopper plate hole.
![]() |
Remove the 2 bolts and No. 1 chain tensioner assembly.
| 32. REMOVE CHAIN TENSIONER SLIPPER |
![]() |
Remove the chain tensioner slipper.
| 33. REMOVE NO. 1 CHAIN SUB-ASSEMBLY |
![]() |
Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.
| *1 | Center Line |
| *2 | Timing Mark |
| *3 | Sensor Plate |
Remove the pulley set bolt.
![]() |
Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.
![]() |
Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.
Remove the chain sub-assembly.
| *A | for Bank 1 |
| 34. REMOVE NO. 1 IDLE GEAR SHAFT |
![]() |
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.
| 35. REMOVE NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 bolts and No. 1 chain vibration damper.
| 36. REMOVE NO. 2 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 No. 2 chain vibration dampers.
| 37. REMOVE CRANKSHAFT TIMING SPROCKET |
![]() |
Remove the crankshaft timing sprocket.
| 38. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1) |
![]() |
While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
![]() |
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the 2 bolts and camshaft timing gear assembly together with the No. 2 chain.
| 39. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the bolt and No. 2 chain tensioner assembly.
| 40. REMOVE CAMSHAFT BEARING CAP (for Bank 1) |
![]() |
Check that the camshafts are positioned as shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
![]() |
Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.
Remove the 5 camshaft bearing caps.
Remove the camshaft and No. 2 camshaft.
| 41. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH |
![]() |
Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
| *1 | Protective Tape |
| 42. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2) |
![]() |
While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
![]() |
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the 2 bolts and camshaft timing gear together with the No. 2 chain.
| 43. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the bolt and No. 3 chain tensioner assembly.
| 44. REMOVE CAMSHAFT BEARING CAP (for Bank 2) |
![]() |
Check that the camshafts are positioned as shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
![]() |
Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 13 bearing cap bolts in several steps in the sequence shown in the illustration.
Remove the 5 camshaft bearing caps.
Remove the No. 3 camshaft and No. 4 camshaft.
| 45. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH |
![]() |
Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
| *1 | Protective Tape |
| 46. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
Remove the 24 No. 1 valve rocker arm sub-assemblies from the cylinder head.
| 47. REMOVE VALVE LASH ADJUSTER ASSEMBLY |
Remove the 24 valve lash adjuster assemblies from the cylinder head.
| 48. REMOVE VALVE STEM CAP |
Remove the 24 valve stem caps from the cylinder head.
| 49. REMOVE CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
Remove the cylinder head sub-assembly.
| 50. REMOVE CYLINDER HEAD LH |
![]() |
Uniformly loosen and remove the 2 cylinder head set bolts in several steps in the sequence shown in the illustration.
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
Remove the cylinder head LH.
| 51. REMOVE CYLINDER HEAD GASKET |
| 52. REMOVE NO. 2 CYLINDER HEAD GASKET |
| 53. REMOVE NO. 1 WATER OUTLET PIPE |
![]() |
Detach the 3 wire harness clamps.
Remove the 2 nuts, bolt and water outlet pipe.
| 54. REMOVE KNOCK SENSOR |
![]() |
Disconnect the 2 sensor connectors.
Remove the 2 bolts and 2 sensors.
| 55. REMOVE CYLINDER BLOCK WATER JACKET SPACER |
![]() |
Remove the 2 cylinder block water jacket spacers from the cylinder block.
| 56. REMOVE NO. 1 TAPER SCREW PLUG |
| 57. REMOVE STRAIGHT PIN |
| 58. REMOVE RING PIN |
| 59. REMOVE STUD BOLT |